SN75158D - Dual RS-422 Line Driver | Texas Instruments
MPN: SN75158D ✓ فعالSN75158D نمای کلی
A differential line driver is an interface IC that converts two single-ended logic signals into complementary differential outputs. In the broader hierarchy, it belongs to line drivers, interface transceivers, and data-communication semiconductors. Differential signaling transmits the same information on two conductors, allowing receiver circuitry to reject common-mode noise and improve reliability over longer cable runs compared with single-ended links.
Each SN75158D transmitter provides high-current source and sink capability suitable for balanced lines at normal line impedance without excessive power dissipation. The device includes a common enable function, enabling the outputs to enter a high-impedance state when the interface is inactive. Its 8-pin SOIC package supports conventional surface-mount assembly and is a practical choice for legacy industrial, telecommunications, instrumentation, and point-to-point data interfaces.
The SN75158 architecture is centered on two independent differential output channels. TTL-compatible totem-pole output stages actively drive one line high while pulling the other low, allowing the differential receiver to recover the intended signal from the voltage between the pair. This arrangement supports full-duplex designs when the receive function is implemented separately and balanced, multidrop point-to-point arrangements when the cable topology and termination strategy meet the interface specifications.
Typical uses include RS-422-compatible links between controllers and peripheral equipment, industrial control consoles, test equipment, telecom peripherals, and legacy instrumentation systems. Because the SN75158 is a driver rather than a complete transceiver, a separate receiver such as the SN75157 family member is required when the same endpoint must both transmit and receive. The operating temperature and 5 V supply requirements make the part especially suitable for conventional commercial equipment rather than automotive or extended-temperature systems.
PCB design should preserve the balanced geometry of each differential pair and provide a continuous ground reference beneath the cable when practical. Keep the complementary outputs routed with matched impedance and avoid adding excessive stub lengths. Confirm the receiver, cable length, connector pinout, enable polarity, and termination arrangement against the complete system interface before releasing a layout.
This product page combines the manufacturer's interface description with practical guidance on application fit, PCB implementation, qualification questions, and same-package alternatives. It also identifies which functions remain outside the transmitter-only device, helping engineers determine whether SN75158D is appropriate before beginning a board-level design.
جایگزینهای drop-in برای SN75158D — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای SN75158D (همان فرمفاکتور و فوتپرینت) — متفاوت در Package, Product Type.
SN75158DR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
SN75158DG4
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
SN75158D مشخصات
| Product Type | Dual differential line driver |
| Number of Drivers | 2 |
| Nominal Supply Voltage | 5 V |
| Maximum Signaling Rate | 10 Mbit/s |
| Supported Interface | RS-422 / ANSI EIA/TIA-422-B / ITU V.11 |
| نوع خروجی | TTL totem-pole differential output |
| Disabled Output State | High impedance |
| محدوده دمای کاری | 0°C to 70°C |
| Fault Protection Range | -10 V to 15 V |
| بستهبندی | 8-pin SOIC (D) |
| Package Pin Count | 8 pins |
| نوع نصب | Surface mount |
| Signal Type | Balanced differential |
| Typical Load | Twisted-pair balanced line at normal line impedance |
راهنمای پیکربندی پین SN75158D 8 pins
پیکربندی پین برای SN75158D (پکیج 8 pins). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای SN75158D.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
SN75158D مناسب است برای 6 کاربردs: Industrial Control Point-to-Point Links, Telecommunications Peripheral Interfaces, Test and Measurement Equipment, Legacy Instrumentation Data Links, RS-422-Compatible Data Ports, Data Acquisition Terminals.
Industrial Control Point-to-Point Links
SN75158D fits industrial point-to-point links that require two balanced transmit channels from a 5 V controller. Its two TTL totem-pole drivers provide active drive for twisted-pair cabling, while the common enable control can place both outputs in a high-impedance state during reset or bus isolation. The 10 Mbit/s maximum signaling rate supports short, high-speed data paths, and the 0°C to 70°C rating suits ordinary indoor control equipment. Designers should maintain closely matched routing between complementary outputs, provide a suitable ground reference where possible, and verify termination against the receiver and cable length. Because SN75158D contains transmitters only, the receiving endpoint requires a separate differential receiver such as the SN75157 family member.
پیشنهادی
Telecommunications Peripheral Interfaces
SN75158D is appropriate for legacy telecommunications peripheral interfaces built around balanced copper wiring and TTL-compatible logic. Its differential outputs reduce susceptibility to common-mode interference compared with a single-ended driver, while the two-channel arrangement supports simultaneous command paths or paired transmit functions. The device operates from a nominal 5 V supply and can signal at rates up to 10 Mbit/s, making it useful for equipment requiring deterministic, point-to-point connections. The disabled high-impedance state helps isolate the line during reset or controlled shutdown. In a telecom chassis, keep the driver close to the line connector, provide a low-impedance return path, and verify that the connector pin assignment and cable topology comply with ANSI EIA/TIA-422-B or ITU V.11 requirements.
پیشنهادی
Test and Measurement Equipment
SN75158D can drive balanced connections from test and measurement instruments that need reliable data transfer over cables longer or noisier than ordinary logic wiring. The two differential transmitters support common-mode rejection at the receiver, while their high-current totem-pole output stages avoid the power dissipation associated with driving a line inefficiently. A maximum signaling rate of 10 Mbit/s accommodates legacy automated-test and laboratory-control interfaces. Use short, geometry-controlled traces and route the outputs toward the connector without unrelated digital activity nearby. The common enable function can suppress line activity during instrument initialization, but the system designer must still confirm timing, cable length, receiver thresholds, and termination because SN75158D does not include receive, equalization, or isolation circuitry.
پیشنهادی
Legacy Instrumentation Data Links
SN75158D is well suited to legacy instrumentation systems that use balanced differential signalling between a controller and a remote measurement or control module. Its two transmitter channels reduce the number of driver packages needed when multiple independent data paths are required, and its 8-pin SOIC format simplifies conventional surface-mount assembly. The device supports operation from 0°C to 70°C, matching many commercial laboratory and industrial instruments. Place each complementary output pair on tightly matched routing, connect the cable shield or ground according to the system grounding method, and avoid long unprotected stubs. Because this is a transmitter-only device, a separate receiver is needed at the remote endpoint, and engineers should evaluate whether modern isolated or differential interface products better meet newer EMC requirements.
پیشنهادی
RS-422-Compatible Data Ports
SN75158D provides the transmit section for an RS-422-compatible data port with two differential channels. ANSI EIA/TIA-422-B and ITU V.11 compatibility makes the device relevant to established balanced-interface equipment, and the high-impedance disabled state supports controlled connection to the cable. The 10 Mbit/s signaling capability is sufficient for many legacy peripheral buses and control links, although actual line rate depends on cable length, loading, termination, and receiver performance. Use a separate SN75157-family receiver at the opposite end and assign the enable function so no partially initialized transmitter drives the line. Because the SN75158D offers no galvanic isolation or integrated termination, those functions must be handled elsewhere in the interface architecture.
پیشنهادی
Data Acquisition Terminals
SN75158D can serve as the outbound interface of a data-acquisition terminal that transfers commands or results to a remote controller over balanced copper cabling. Differential outputs help preserve data integrity in cabinets or installations where common-mode voltage may vary, and two transmitters support paired command or status paths within one package. The device's nominal 5 V operation integrates readily with TTL-based digital systems, while its 0°C to 70°C range covers standard indoor instrumentation environments. Keep the two conductors of each differential pair geometrically matched, place the receiver termination near the receiving device, and minimize copper exposure to unrelated switching nodes. The SN75158D does not perform isolation, so installations with large ground-potential differences require an external isolation strategy.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای SN75158D — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | SN75158DR | SN75158DG4 |
|---|---|---|---|
| Product Type | Dual differential line driver | Dual differential line driver | Dual differential line driver |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Number of Drivers | 2 | 2 | 2 |
| Number of Receivers | 0 | 0 | 0 |
| Nominal Supply Voltage | 5 V | 5 V | 5 V |
| Maximum Signaling Rate | 10 Mbit/s | 10 Mbit/s | 10 Mbit/s |
| Operating Temperature Range | 0°C to 70°C | 0°C to 70°C | 0°C to 70°C |
| Fault Protection Range | -10 V to 15 V | -10 V to 15 V | -10 V to 15 V |
| Interface Standard | ANSI EIA/TIA-422-B and ITU V.11 | ANSI EIA/TIA-422-B and ITU V.11 | ANSI EIA/TIA-422-B and ITU V.11 |
| Output Stage | TTL totem-pole differential output | TTL totem-pole differential output | TTL totem-pole differential output |
تفاوتهای کلیدی
- Two balanced transmit channels in one package (در مقابلSN75157D)
- High-current balanced-line output capability (در مقابلDS9638CM)
- Compatibility with established balanced-interface specifications (در مقابلSN75150D)
یادداشتهای طراحی
Route each complementary output pair with matched geometry and consistent spacing so the two conductors experience nearly identical propagation delays and losses. Keep the traces short, avoid long stubs, and provide a continuous ground reference beneath the cable where the installation permits it. Place any termination at the receiving endpoint according to the complete interface design. Review the connector assignment against the manufacturer's pin-description table before routing because the SOIC footprint alone does not establish pin compatibility.
Do not treat SN75158D as a complete RS-422 transceiver: it contains two transmitters and no receivers. A receiving endpoint requires a separate differential receiver, such as a member of the SN75157 family, and the two devices must use consistent enable timing and signal polarity. Also verify that the external interface voltage remains within the stated -10 V to 15 V fault-protection range. The DS9638CM may serve certain RS-485 designs, but its differing pinout and enable logic make it unsuitable as an automatic board replacement.
The SN75158D is designed for nominal 5 V operation. Decouple the supply locally with a suitable bypass capacitor and keep the supply-return path short to reduce susceptibility to simultaneous switching noise from the TTL totem-pole outputs. Account for both the host's 5 V supply requirements and the current drawn while the differential outputs are active. If the driver is disabled during system reset, ensure the receiver and system firmware interpret the resulting high-impedance line state correctly.
The maximum 10 Mbit/s signaling rate does not by itself guarantee error-free communication over every cable length or topology. Evaluate cable attenuation, loading, stub length, receiver thresholds, and termination for the intended installation. Balanced routing helps reject common-mode noise, but it does not remove the need for a sound ground reference or protection against large transients. Keep switching nodes and high-current outputs away from the differential pair where practical.
اطلاعات انطباق
The interface standards explicitly identified for this product are ANSI EIA/TIA-422-B and ITU V.11. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses were not identified for the exact SN75158D ordering code.