TAS5613APHD - 150W Stereo Class-D Amplifier | TI
MPN: TAS5613APHD ✓ فعالTAS5613APHD نمای کلی
A Class-D audio amplifier is a switching power amplifier that uses transistor output stages to deliver audio energy efficiently. In the signal path, an analog input is amplified and converted into a high-frequency switching waveform. The speaker reconstructs the audio signal through its filtering characteristics. Compared with a linear output stage, Class-D architecture can reduce heat and power loss, while the TAS5613APHD adds integrated feedback for low distortion and reliable speaker drive.
Key capabilities include up to 150 W per channel into a 4-ohm stereo load, up to 300 W in mono operation, an 18 V to 38 V analog power-supply range, and integrated PurePath HD feedback. The manufacturer datasheet states that achievable output power depends on the thermal configuration of the target application. The 14 mm by 14 mm HTQFP package therefore requires careful exposed-pad heat transfer and an appropriately sized thermal design.
The device is designed for analog-input audio systems and includes active enable control, integrated feedback, and protection functions associated with the TAS5613A family. Its power-stage architecture is intended to simplify design around high-power Class-D amplification. External filtering, supply decoupling, output-network selection, and thermal-interface materials remain central to achieving clean, stable operation at high output power.
Typical applications include 150 W stereo active speakers, 300 W mono subwoofers, multi-zone residential audio, powered cinema speakers, and professional monitor amplifiers. Its dual-channel configuration can also support parallel or bridged arrangements where the board design and speaker impedance permit them. The relatively high supply requirement makes it more appropriate for mains-powered or automotive 24 V systems than for low-voltage portable equipment.
Thermal design is the primary implementation constraint. Place the exposed pad against a thermal interface and substantial copper area, then use the manufacturer datasheet’s recommended PCB layout and reference-design power-supply components. Verify output-power capability across ambient temperature, speaker impedance, supply voltage, and enclosure temperature rather than relying on the headline power rating alone.
This product summary combines the family-level power capability, package information, supply range, and application positioning with practical guidance for thermal management, board layout, sourcing, and drop-in replacement assessment. It also organizes the most relevant companion audio components and engineering trade-offs into a design-oriented reference for amplifier selection.
جایگزینهای drop-in برای TAS5613APHD — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
TAS5613PHDR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TAS5613APHDR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TAS5613A
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TAS5613APHD حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | Class-D audio power amplifier |
| Amplifier Configuration | 1-channel mono or 2-channel stereo |
| Stereo Output Power | 150 W |
| Mono Output Power | 300 W |
| Supply Voltage Range | 18 V to 38 V |
| Input Type | Analog input |
| Feedback Architecture | PurePath HD integrated closed-loop feedback |
| بستهبندی | 64-pin HTQFP (PHD), 14 mm x 14 mm |
| Exposed Pad | Yes |
| نوع نصب | Surface mount |
| دمای کاری | 105 C maximum |
| Recommended Speaker Load | 4 ohm |
| Output Stage | PurePath HD Class-D power stage |
| Enable Control | Active enabled |
راهنمای پیکربندی پین TAS5613APHD 64-pin htqfp (phd), 14 mm x 14 mm
پیکربندی پین برای TAS5613APHD (پکیج 64-pin htqfp (phd), 14 mm x 14 mm). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای TAS5613APHD.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
TAS5613APHD مناسب است برای 6 کاربردs: High-Power Stereo Powered Speaker, 300W Mono Subwoofer Amplifier, Home-Theater Multi-Channel Amplifier, Professional Active Monitor, Automotive High-Power Audio, Powered Speaker and Subwoofer Platform.
High-Power Stereo Powered Speaker
The TAS5613APHD fits a powered stereo-speaker architecture requiring as much as 150 W per channel into a 4-ohm load. Its two-channel analog-input Class-D arrangement reduces the number of separate power-stage packages needed by a conventional multi-amplifier design. Place the device behind the input and gain-control network, connect the recommended LC output filtering, and use a low-noise 18 V to 38 V supply. The principal engineering benefit is high conversion efficiency, while the trade-off is a substantial 64-pin HTQFP footprint and exposed-pad cooling requirement. Continuous output must be derated according to the actual heat-sink area, PCB copper, ambient temperature, and enclosure ventilation.
پیشنهادی
300W Mono Subwoofer Amplifier
The TAS5613APHD can be configured for up to 300 W mono operation, making it appropriate for a high-output subwoofer or low-frequency monitor power stage. Use one channel for the power-amplification role and the available channel according to the manufacturer configuration guidance. The 4-ohm operating point and integrated PurePath HD feedback support efficient Class-D drive, but output distortion and thermal performance still depend on the external output network, supply impedance, PCB layout, and heat sinking. Design the enclosure for sustained low-frequency power rather than only short-duration peaks, and verify that the speaker excursion, protection circuitry, and voice-coil thermal limits suit the intended program material.
پیشنهادی
Home-Theater Multi-Channel Amplifier
A multi-channel home-theater rack can use TAS5613APHD devices as efficient high-power analog-input stages behind a surround-sound decoder. The 150 W stereo capability supports demanding floor-standing speakers, while the 18 V to 38 V supply range suits higher-power amplifier modules. Its integrated closed-loop feedback helps the amplifier maintain low distortion as supply and load conditions vary. The system designer should budget several exposed-pad thermal zones, use star-point or low-impedance supply distribution, and preserve analog signal integrity between the preamplifier, gain network, and power-stage inputs. Filtering components and speaker wiring should follow the manufacturer reference circuits to avoid instability, excessive loss, or reduced protection effectiveness.
پیشنهادی
Professional Active Monitor
The TAS5613APHD suits a professional active monitor or stage-monitor power module that requires predictable high-output Class-D amplification from an analog input. Its 150 W per-channel capability offers useful headroom for demanding monitor levels, while integrated PurePath HD feedback supports consistent speaker drive. Because studio and touring equipment is vibration-sensitive, mechanically secure the heat sink and use a thermal interface material that remains stable over the operating temperature range. Separate sensitive preamplifier grounding from the high-current output and supply return paths, and place the input filtering close to the device. Confirm the output-filter component tolerances and excursion requirements using the manufacturer application information.
پیشنهادی
Automotive High-Power Audio
The TAS5613APHD can support a high-power automotive audio amplifier where the electrical system can provide a stable 18 V to 38 V rail and the amplifier has been qualified for the vehicle environment. Its 300 W mono capability is useful for a subwoofer, while stereo operation can drive front or rear speakers. The implementation must address automotive transient protection, electromagnetic interference, ground offsets, and enclosure temperature beyond ordinary consumer-audio assumptions. The published 105 C maximum operating temperature does not by itself establish AEC-Q100 qualification. Confirm qualification, automotive validation, production status, and the exact load-dump requirements with Texas Instruments before releasing the design for vehicle use.
پیشنهادی
Powered Speaker and Subwoofer Platform
A modular powered-speaker platform can standardize on the TAS5613APHD for both a 150 W stereo main channel and a 300 W mono subwoofer channel. Because both functions use the same family architecture, the designer can simplify supply planning, control-interface design, thermal qualification, and production test procedures. Use independent enable sequencing where amplifier startup could damage downstream circuitry, and select output-filter values according to each channel’s intended crossover frequency. The key trade-off is board area: each 64-pin HTQFP device requires a substantial exposed-pad thermal area, so adjacent channels require careful copper partitioning to prevent thermal coupling between amplifiers.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای TAS5613APHD — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | TAS5613PHDR | TAS5613APHDR | TAS5613A |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 64-pin HTQFP (PHD), 14 mm x 14 mm | 64-pin HTQFP | 64-pin HTQFP | 64-pin HTQFP (PHD) |
| Stereo Output Power | 150 W | 150 W | 150 W | 150 W |
| Amplifier Class | Class D | Class D | Class D | Class D |
| Input Type | Analog input | Analog input | Analog input | Analog input |
| Ordering Configuration | TAS5613APHD tray configuration | TAS5613PHDR ordering identity | TAS5613APHDR ordering identity | TAS5613A family designation |
تفاوتهای کلیدی
- Combines 150 W stereo and 300 W mono capability in one analog-input power stage (در مقابلTAS5613PHDR)
- Uses a manufacturer-documented 64-pin HTQFP power-stage package (در مقابلTAS5613A)
- Integrated PurePath HD feedback supports efficient Class-D operation (در مقابلTAS5613APHDR)
- Tray ordering identity targets production and direct-board assembly workflows (در مقابلTAS5613APHDR)
یادداشتهای طراحی
Use the exposed pad as the primary thermal path and couple it to the heat sink through an appropriate high-conductivity interface material. The Texas Instruments datasheet states that achievable output power depends on the thermal configuration, so do not assume the 150 W stereo or 300 W mono ratings apply to an unrestricted copper pour. Validate the final assembly with the intended heat sink, enclosure airflow, ambient temperature, supply voltage, and continuous load.
Follow the TAS5613A reference-design PCB layout for the power-supply components and high-current paths. Keep the analog input routing away from output-switching nodes and the 18 V to 38 V supply distribution. Use short, wide copper for ground and supply connections, minimize loop area, and maintain the exposed-pad solder and via structure specified by the manufacturer. The 12 V internal supply arrangement called out in the datasheet should originate from a low-noise, low-output-impedance regulator.
Place the external output-filter components and their return connections according to the manufacturer application diagrams. Keep sensitive input and feedback traces short and away from the switching output node and inductor. Route the two output channels with adequate separation to minimize crosstalk, and connect the device ground and exposed pad as directed rather than relying on a narrow thermal or signal-ground path. Review the complete pin-description table before finalizing track assignments.
Do not select the amplifier from headline wattage alone. Confirm minimum and maximum supply voltage, speaker impedance, output-filter topology, thermal conditions, and protection requirements for the exact ordering part. When replacing TAS5613APHD with TAS5613PHDR, TAS5613APHDR, or another TAS5613A ordering identity, verify the applicable datasheet revision and pin table. A matching 64-pin HTQFP outline does not by itself prove that every limit and configuration is identical.
اطلاعات انطباق
The verified excerpts do not provide specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements. Automotive qualification must be confirmed directly with Texas Instruments for vehicle applications.