TJA1040T/N1 - 1 Mbit/s CAN Transceiver | NXP Semiconductors
MPN: TJA1040T/N1 ✗ پایان تولیدTJA1040T/N1 نمای کلی
A CAN transceiver is a semiconductor interface device that converts logic-level transmit and receive signals into the differential signaling used on a Controller Area Network. In the hierarchy of electronic components, the TJA1040T/N1 is an interface IC, specifically a CAN physical-layer transceiver. A host microcontroller or dedicated CAN controller handles message framing, arbitration, filtering, and protocol timing, while the transceiver translates those controller signals into robust bus-level voltages and converts received bus states into logic-compatible data.
The key operating headline is a maximum data rate of 1 Mbit/s, with differential transmit and receive capability. The 8-SO package keeps the physical interface compact for automotive electronic control units and other embedded CAN systems. The NXP product page specifically identifies passenger cars as the principal application environment. These characteristics make the TJA1040T/N1 relevant to designs that need a conventional high-speed CAN physical layer rather than a low-speed fault-tolerant body-network interface.
The TJA1040T/N1 belongs to an older generation of CAN transceivers whose successor products can add functions such as standby control, split-buffer operation, or expanded I/O voltage support. Its core role remains straightforward: TXD accepts a controller-side transmit signal, RXD presents the received bus state to the controller, and the differential CANH and CANL pins connect to the bus. Exact electrical limits, loopback behavior, and pin functions should be checked against the manufacturer data sheet before final circuit release.
Typical applications include passenger-car body-control modules, powertrain controllers, automotive comfort systems, CAN-based sensors, and industrial or embedded equipment using a standard 1 Mbit/s CAN network. In an automotive control unit, the transceiver provides the physical link between a CAN controller and the two-wire bus while leaving protocol functions to the controller. Its differential interface also suits systems where minimizing susceptibility to common-mode noise is important.
PCB design should preserve the short, symmetric CANH and CANL connection between the transceiver and the bus connector, keep the connector and bus stubs short, and provide the required decoupling directly at the device supply pins. The 8-SO footprint simplifies assembly but requires careful escape routing around the two bus pins. Review the recommended application circuit, termination requirements, supply voltage, and loopback configuration in the NXP data sheet when laying out the module.
This product record combines the manufacturer interface description, ordering information, package details, lifecycle information, and replacement guidance with practical PCB considerations. It also distinguishes strict same-footprint substitutes from newer CAN transceivers that offer additional functions but may require different pin interpretation or board-level qualification.
جایگزینهای drop-in برای TJA1040T/N1 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
TJA1042T/3,1J
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
SN65HVD1040
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TJA1040T/N1 مشخصات
| Product Type | 1 high-speed CAN transceiver per package |
| Maximum CAN Data Rate | 1 Mbit/s |
| Protocol | Controller Area Network (CAN) |
| Transmit Interface | 1 differential CAN output channel |
| Receive Interface | 1 differential CAN input channel |
| Bus Pins | 2 differential pins (CANH and CANL) |
| بستهبندی | 8-SO, 8 pins |
| نوع نصب | Surface mount |
| Manufacturer | NXP Semiconductors |
| Primary Application | Passenger-car high-speed CAN networks |
راهنمای پیکربندی پین TJA1040T/N1 8-so, 8 pins
پیکربندی پین برای TJA1040T/N1 (پکیج 8-so, 8 pins). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای TJA1040T/N1.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
TJA1040T/N1 مناسب است برای 6 کاربردs: Passenger-Car Body Control Module, Powertrain CAN Interface, Automotive Comfort and Convenience System, CAN-Based Sensor Node, Industrial CAN Controller Module, Existing Automotive ECU Retrofit.
Passenger-Car Body Control Module
The TJA1040T/N1 fits a body control module that connects a CAN controller to passenger-car body networks operating up to 1 Mbit/s. Its differential transmitter drives the CANH and CANL bus conductors, while its differential receiver returns the bus state to the controller for decoding. This arrangement separates physical-layer signaling from protocol processing and allows the controller to handle arbitration, filtering, and diagnostics. The 8-SO package also supports compact control-unit layouts, although CANH and CANL routing must remain short and reasonably symmetric. Designers should verify supply limits, TXD and RXD thresholds, bus fault behavior, and the exact temperature-grade ordering code against the NXP data sheet.
پیشنهادی
Powertrain CAN Interface
The TJA1040T/N1 provides a high-speed physical interface for an engine, transmission, or powertrain controller that exchanges data over a standard 1 Mbit/s CAN bus. Because the controller performs message scheduling and protocol checking, the transceiver can concentrate on robust differential bus communication. Its 1 Mbit/s capability matches the high-speed passenger-car network class identified by NXP. Layout remains the decisive integration concern: place the device and its decoupling close to the controller, keep the two bus traces away from fast digital edges, and route them toward the connector without long unprotected stubs. The selected package and vehicle qualification requirements should also be confirmed during component validation.
پیشنهادی
Automotive Comfort and Convenience System
TJA1040T/N1 can form the bus-facing section of a door, lighting, climate, or seat-control module that communicates with other passenger-car electronic units at up to 1 Mbit/s. The transceiver converts the controller's TXD signal into differential CANH and CANL activity and presents the received bus condition on RXD. This allows compact modules to participate in a shared vehicle network without implementing the physical layer in discrete components. Because switching relays, motors, and LED drivers can introduce electrical noise, engineers should follow the manufacturer's application circuit, preserve short bus connections, and use appropriate protection and filtering at the connector. Confirm the operating temperature and qualification requirements for the target vehicle program.
پیشنهادی
CAN-Based Sensor Node
The TJA1040T/N1 is suitable for a compact sensor or actuator node that reports measurements to a CAN controller at a standard high-speed CAN rate. Differential signaling helps the node communicate over a shared two-wire bus while rejecting common-mode disturbance encountered in industrial or vehicle environments. The controller determines message content and timing, while the transceiver supplies the physical-layer drive and receive paths. For a sensor placed away from the main controller, the designer should minimize the unprotected bus stub, maintain a controlled termination strategy, and validate operation across voltage and temperature extremes. Because the target MPN is obsolete, a new design should also compare the SN65HVD1040 or a current NXP transceiver before committing the layout.
پیشنهادی
Industrial CAN Controller Module
The TJA1040T/N1 can serve as the physical-layer element in an embedded industrial module using a conventional 1 Mbit/s CAN network. It allows a microcontroller with a CAN controller, or a dedicated protocol controller, to exchange messages over a differential bus without implementing transmitter and receiver circuits on the controller board. The 8-SO footprint supports compact modules, while its automotive origins make it relevant to equipment requiring robust differential communication. The integration should include local supply decoupling, short CANH and CANL exits, appropriate connector protection, and a termination arrangement compatible with the bus topology. Review the NXP absolute maximum ratings and timing limits for industrial temperature, ground-offset, and fault-recovery conditions.
پیشنهادی
Existing Automotive ECU Retrofit
TJA1040T/N1 is most relevant when maintaining or repairing an existing automotive electronic control unit that uses the established TJA1040 8-SO physical interface. Retaining the familiar footprint can reduce the scope of a board-level redesign, provided the replacement part is checked for matching supply voltage, logic levels, mode configuration, timing, and temperature grade. The TJA1040T/N1 is listed as obsolete, so procurement planning should focus on confirmed stock and traceable sourcing rather than expecting a standard active-production cycle. For functional safety or long-term production programs, engineers should compare the candidate with a current qualified transceiver and complete its own qualification review before releasing a new vehicle build.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای TJA1040T/N1 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | TJA1042T/3,1J | SN65HVD1040 |
|---|---|---|---|
| Package | 8-SO | SO-8 | SO-8 |
| Brand | NXP Semiconductors | NXP Semiconductors | Texas Instruments |
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver |
| Maximum Data Rate | 1 Mbit/s | 1 Mbit/s class | 1 Mbit/s class |
| Differential Transmit | Supported | Supported | Supported |
| Differential Receive | Supported | Supported | Supported |
| Primary Application | Passenger-car high-speed CAN networks | High-speed CAN networks | High-speed CAN networks |
| Mode and Control Features | Conventional TJA1040 mode behavior | Newer mode behavior; SPLIT position repurposed | Conventional TJA1040-style mode behavior |
تفاوتهای کلیدی
- Established 1 Mbit/s high-speed CAN physical interface (در مقابلSN65HVD1040)
- Direct compatibility pathway for existing passenger-car CAN layouts (در مقابلTJA1042T/3,1J)
- Known lifecycle position for legacy maintenance decisions (در مقابلTJA1042T/3,1J)
یادداشتهای طراحی
Route CANH and CANL as a close, balanced pair from the TJA1040T/N1 to the connector or bus interface. Avoid long stubs, abrupt impedance discontinuities, and routing either conductor beside high-current switching nodes. Place the transceiver near the protected connector-side entry point where practical, while keeping its supply decoupling close to the device. Confirm the final pad assignments and exposed package geometry from the NXP data-sheet drawing before releasing artwork.
Do not assume that every 8-pin CAN transceiver is electrically interchangeable. The TJA1042 changes the role associated with the earlier SPLIT position, and newer parts may add VIO, standby, or diagnostic functions. For a proposed replacement, compare TXD and RXD thresholds, propagation delay, supply range, bus fault behavior, mode states, and temperature grade. A matching SO-8 outline alone does not prove drop-in compatibility.
Implement the manufacturer-recommended application circuit and place all required local capacitors adjacent to the appropriate supply pins. Keep the CAN bus interface away from switching regulators, inductors, high-current relays, and crystal-clock routing. Use a termination strategy appropriate for the complete bus topology, and evaluate connector-level ESD protection without adding excessive capacitance to CANH or CANL. Validate the assembled board for dominant and recessive bus states and controller recovery after faults.
اطلاعات انطباق
The manufacturer product page and data sheet links are identified, but definitive compliance and qualification statements for the exact TJA1040T/N1 ordering code were not present in the cited excerpts.