NXP Semiconductors

TJA1042ATK/3/0Z - 5Mbps CAN FD Transceiver | NXP

MPN: TJA1042ATK/3/0Z ✓ فعال
4.5 V to 5.5 V Vdss 8-HVSON exposed-pad package Package Improved EMC performance Memory
حداقل سفارش: 1 |

TJA1042ATK/3/0Z نمای کلی

NXP Semiconductors TJA1042ATK/3/0Z is a high-speed CAN and CAN FD transceiver with a maximum data rate of 5 Mbit/s, a 5 V transceiver supply, and an 8-HVSON exposed-pad package measuring 3 x 3 mm. It provides the physical-layer interface between a CAN protocol controller and a two-wire CAN bus, combining high-speed data transfer with low-power standby operation.

A CAN transceiver is an interface IC that converts logic-level controller signals into differential CAN bus levels and reconstructs bus signals for the controller. Within the communication hierarchy, the TJA1042ATK/3/0Z belongs to the CAN transceiver class, interface ICs, wired-communication semiconductors, and automotive electronics. Its differential bus interface supports robust automotive networking while the transceiver handles electrical protection and bus interfacing.

Key characteristics include support for communication rates up to 5 Mbit/s, a 4.5 V to 5.5 V transceiver operating range, and a low-power Standby mode with bus wake-up capability. The automotive-grade version is identified as AEC-Q100 compliant in the product listing. Its 8-HVSON package uses an exposed pad to improve heat dissipation while keeping the PCB footprint compact.

The TJA1042 family is designed for reliable CAN and CAN FD communication with improved electromagnetic compatibility and electrostatic-discharge performance. The passive behavior of the bus pins when the device is unpowered helps a connected node avoid disrupting communication from other operating nodes. These characteristics are useful in distributed automotive and industrial control networks where cable length, electromagnetic interference, and partial power loss are important system considerations.

Typical applications include automotive body and chassis control modules, industrial CAN gateways, vehicle diagnostic interfaces, battery-management systems, and distributed automation controllers. A CAN protocol controller or MCU with an integrated CAN controller connects to the TJA1042 through TXD, RXD, and enable-related pins, while CANH and CANL connect to the bus through the network termination and protection scheme.

For PCB implementation, place the transceiver close to the CAN bus connector and keep the CANH and CANL traces short, symmetric, and free from switching nodes. Follow the manufacturer pin and layout guidance when connecting the exposed pad, supply decoupling, split-capacitor option, bus termination, and protection components. Account for the common-mode and transient-voltage environment of an automotive bus.

This page combines the exact ordering information, electrical envelope, automotive qualification, package details, drop-in alternatives, application guidance, and design considerations needed to evaluate the TJA1042ATK/3/0Z before PCB implementation or sourcing.

جایگزین‌های drop-in برای TJA1042ATK/3/0Z — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای TJA1042ATK/3/0Z (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Low-Power Mode, Package, Product Type.

NXP Semiconductors
Low-Power Mode: Standby mode
Package: 8-HVSON, 3 mm x 3 mm
Product Type: High-speed CAN transceiver with Standby mode

TJA1042TK/3/0Z

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-HVSON (3 x 3 mm)
Same HVSON footprint and 5 Mbit/s CAN class; ordering-code interface and standby details require confirmation against the NXP ordering table.

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1042TK/3/1J

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
NXP Semiconductors
📦 8-HVSON (3 x 3 mm)
High-speed CAN transceiver with Standby mode · 5 Mbit/s · CAN and CAN FD · Two-wire differential CAN bus · 1 transmit and 1 receive channel · 2.8 V · 3.5 V · Single transceiver supply

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

TJA1042ATK/3/0Z مشخصات

Product Type High-speed CAN and CAN FD transceiver
Maximum Data Rate 5 Mbit/s
Transceiver Supply Voltage Range 4.5 V to 5.5 V
Nominal Transceiver Supply 5 V
Bus Interface Two-wire differential CAN bus
Logic Interface 5 V
Low-Power Mode Standby mode with bus wake-up capability
Unpowered Behavior Passive bus-pin behavior
Automotive Qualification AEC-Q100
محدوده دمای اتصال کاری -40 °C to +150 °C
بسته‌بندی 8-HVSON exposed-pad package
Package Dimensions 3 x 3 mm
تعداد پایه 8 pins
نوع نصب Surface mount
Packaging Tape and reel
Product Status Active
Number of Transceivers per Package 1 transceiver
Electromagnetic Compatibility Improved EMC performance
Electrostatic Discharge Performance Improved ESD performance

راهنمای پیکربندی پین TJA1042ATK/3/0Z 1 transceiver

پیکربندی پین برای TJA1042ATK/3/0Z (پکیج 1 transceiver). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 1 transceiver برای TJA1042ATK/3/0Z

داده پین‌آوت تفصیلی موجود نیست برای TJA1042ATK/3/0Z.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

TJA1042ATK/3/0Z مناسب است برای 6 کاربردs: Automotive Body Control Module, Vehicle Diagnostic Gateway, Industrial CAN Gateway, Battery Management System, Distributed Automation Controller, Electric Vehicle Powertrain Controller.

🚗

Automotive Body Control Module

The TJA1042ATK/3/0Z fits an automotive body controller because it supports CAN and CAN FD communication up to 5 Mbit/s while operating from a 5 V supply. Its AEC-Q100 qualification, -40 °C to +150 °C junction-temperature range, improved EMC performance, and improved ESD performance suit demanding vehicle networks. The 8-HVSON 3 x 3 mm exposed-pad package also limits board area beside a microcontroller or CAN controller. Place the transceiver near the vehicle harness connector, use a balanced CANH/CANL route, and connect the exposed pad according to the manufacturer land-pattern guidance. The primary design trade-off is that the compact package offers less forgiving rework than a conventional SOIC-8 device.

🚗

Vehicle Diagnostic Gateway

A diagnostic gateway can use the TJA1042ATK/3/0Z as the physical interface between a CAN protocol controller and a two-wire vehicle bus. The transceiver's 5 Mbit/s capability provides sufficient bandwidth for CAN FD diagnostics, while standby mode with bus wake-up capability supports systems that must remain low-power until network activity occurs. Its passive behavior when unpowered is particularly useful in mixed operating states because it helps avoid loading the bus. The engineer should define bus protection for automotive transients, follow the manufacturer's exposed-pad and decoupling layout, and confirm that the 4.5 V to 5.5 V operating range matches the controller rail.

🏭

Industrial CAN Gateway

The TJA1042ATK/3/0Z is appropriate for an industrial CAN gateway that links a local controller with sensors, drives, or remote I/O modules. Its 5 Mbit/s maximum data rate supports high-speed CAN and CAN FD traffic, while the -40 °C to +150 °C junction-temperature range provides broad thermal headroom for rugged equipment. The compact 8-HVSON package is useful where connector routing and PCB space are constrained. Route the differential bus as a short pair, include termination and transient protection, and test electromagnetic compliance with the final cable and enclosure. Because this is an automotive-qualified CAN interface, harsh industrial use still requires appropriate input protection and qualification at the system level.

⚡

Battery Management System

The TJA1042ATK/3/0Z can connect a battery-management controller to a CAN-based traction, charging, or energy-storage network. Its 5 Mbit/s capability allows efficient communication among battery modules, contactors, supervisory electronics, and a vehicle controller. Standby mode with bus wake-up capability supports systems that periodically sleep between activity periods, while passive unpowered behavior helps preserve bus communication during partial power loss. The 5 V transceiver supply must be derived from the battery-management electronics with appropriate regulation and transient rejection. Use a short CANH/CANL route, provide the specified bus protection, and use the exposed pad as directed for reliable thermal performance in a compact controller enclosure.

🏭

Distributed Automation Controller

A distributed automation controller can use the TJA1042ATK/3/0Z when a compact, high-speed wired interface is needed between a real-time controller and field equipment. The 5 Mbit/s CAN capability supports deterministic message exchange among sensors and actuators, while standby mode limits consumption during inactive intervals. Its automotive-grade qualification and wide -40 °C to +150 °C junction-temperature range are beneficial in temperature-variable installations, although the complete product must satisfy its own industrial requirements. The 3 x 3 mm HVSON footprint reduces connector-adjacent board area, and the exposed pad helps remove heat. Confirm bus termination, fault protection, common-mode behavior, and firmware timing before deployment.

⚡

Electric Vehicle Powertrain Controller

The TJA1042ATK/3/0Z can serve as the CAN interface in an electric-vehicle powertrain controller when the network is designed for high-speed CAN or CAN FD communication. The 5 Mbit/s limit supports controller-to-controller status, torque, fault, and diagnostic messages, while improved EMC and ESD performance address important automotive interface concerns. The compact exposed-pad package fits near the controller and connector, but thermal design must account for copper area and the pad connection specified by NXP. Use a protected two-wire bus layout and validate transient immunity, bus fault behavior, standby wake-up, and unpowered loading in the complete vehicle electrical environment.

خلاصه محصولات پیشنهادی

TJA1042AT/3/0Z NXP Semiconductors استفاده‌شده در: Automotive Body Control Module, Industrial CAN Gateway, Distributed Automation Controller TJA1057GTK/3Z NXP Semiconductors استفاده‌شده در: Automotive Body Control Module, Vehicle Diagnostic Gateway, Industrial CAN Gateway, Battery Management System, Distributed Automation Controller TJA1042TK/3/1 Closely related HVSON CAN transceiver ordering option استفاده‌شده در: Vehicle Diagnostic Gateway, Electric Vehicle Powertrain Controller TJA1042TK/3/0Z Same-family HVSON option for interface configuration review استفاده‌شده در: Battery Management System, Electric Vehicle Powertrain Controller
What is the TJA1042ATK/3/0Z?
The TJA1042ATK/3/0Z is an NXP Semiconductors high-speed CAN and CAN FD transceiver rated for data rates up to 5 Mbit/s. It interfaces a CAN controller or MCU with a two-wire differential CAN bus, operates from a 4.5 V to 5.5 V transceiver supply, and is packaged in an 8-HVSON 3 x 3 mm exposed-pad package for automotive and industrial control systems.
What is the operating voltage of TJA1042ATK/3/0Z?
The TJA1042ATK/3/0Z operates from a 4.5 V to 5.5 V transceiver supply, with 5 V as the nominal operating voltage. The NXP TJA1042 family information identifies this part as a 5 V CAN transceiver with a 5 V logic interface. Supply decoupling and exposed-pad layout must follow the manufacturer guidance to keep the transceiver within its specified electrical operating range.
What is the maximum CAN data rate of TJA1042ATK/3/0Z?
The TJA1042ATK/3/0Z supports CAN and CAN FD communication at data rates up to 5 Mbit/s. This rate is the principal performance identifier in the product listing and NXP family description. The achievable bus rate also depends on controller timing, cable length, termination, transceiver characteristics, and the electromagnetic environment of the complete CAN network.
Where can I download the TJA1042ATK/3/0Z datasheet and find its pinout?
The official TJA1042 documentation is available through the NXP product page at https://www.nxp.com/products/TJA1042, and the ordering-code entry is at https://www.nxp.com/part/TJA1042TK. Use the manufacturer datasheet and pin-description table when assigning TXD, RXD, supply, ground, bus, and exposed-pad connections. Verify the exact 8-HVSON footprint and exposed-pad requirements against the ordering-code documentation.
What package does the TJA1042ATK/3/0Z use?
The TJA1042ATK/3/0Z uses an 8-HVSON exposed-pad package measuring 3 x 3 mm and is supplied on tape and reel. The exposed pad is part of the thermal and electrical construction of the package and must be connected according to the manufacturer layout instructions. A conventional SOIC-8 footprint is not compatible with this HVSON arrangement.
Is the TJA1042ATK/3/0Z suitable for automotive applications?
Yes, the TJA1042ATK/3/0Z is identified as an automotive AEC-Q100 CAN transceiver with an operating junction-temperature range of -40 °C to +150 °C. Its high-speed CAN and CAN FD capability, improved EMC performance, improved ESD performance, and passive unpowered behavior are suited to vehicle networks. Final suitability still depends on the module's voltage environment, protection strategy, qualification requirements, and system validation.
Where to buy TJA1042ATK/3/0Z online?
Use the Request a Quote form on this page to request the exact TJA1042ATK/3/0Z ordering code, current commercial availability, and a quotation tailored to the required quantity. The order code includes the HVSON package and automotive ordering information, so confirm that the quoted line item is TJA1042ATK/3/0Z rather than the SOIC-8 TJA1042AT/3/0Z variant.
What is the price of TJA1042ATK/3/0Z?
The current commercial price for TJA1042ATK/3/0Z is best obtained through the Request a Quote form on this page because quotations can depend on quantity, inventory, and purchasing terms. Submit the exact MPN and required package quantity for an accurate response. Do not substitute the TJA1042AT/3/0Z, which uses a different 8-SO package.
What is the lead time and stock status for TJA1042ATK/3/0Z?
Request current stock, minimum order quantity, and lead time through the Request a Quote form on this page. The manufacturer lists the TJA1042 family as active, while a distributor listing reports 6,000-piece minimum ordering and a 10-week lead-time indication. Confirm all commercial terms directly because availability and scheduling can change after the listing date.
What can replace the TJA1042ATK/3/0Z?
The closest same-footprint options identified for the TJA1042ATK/3/0Z are TJA1042TK/3/0Z and TJA1042TK/3/1, both using an 8-HVSON arrangement, but each ordering code must be checked for logic-interface and standby details. The TJA1042AT/3/0Z is not a drop-in alternative because it uses an 8-SO package. Use the manufacturer ordering-information table before approving any substitution.
Is TJA1042ATK/3/0Z the same as TJA1042AT/3/0Z?
No, the TJA1042ATK/3/0Z and TJA1042AT/3/0Z use different packages. The K ordering code identifies the 8-HVSON 3 x 3 mm exposed-pad package, while the AT ordering code identifies an 8-SO package. Their shared TJA1042 family name does not make them PCB drop-in replacements, and the footprint, exposed pad, and soldering process must be reviewed separately.
TJA1042ATK/3/0Z vs TJA1042TK/3/0Z: which should be selected?
The TJA1042ATK/3/0Z and TJA1042TK/3/0Z are closely related 8-HVSON CAN transceiver options, but the exact ordering-code differences must be confirmed against NXP documentation. Compare the controller interface voltage, standby behavior, wake-up configuration, and exposed-pad implementation before choosing. For an existing TJA1042ATK/3/0Z PCB, retain the original ordering code unless the manufacturer confirms that the complete device configuration is equivalent.
When should I choose the TJA1042ATK/3/0Z instead of an SOIC-8 CAN transceiver?
Choose the TJA1042ATK/3/0Z when the PCB uses an 8-HVSON 3 x 3 mm footprint and requires the part's 5 Mbit/s CAN or CAN FD operation, AEC-Q100 automotive qualification, standby wake-up behavior, and exposed-pad thermal design. An SOIC-8 replacement requires a different footprint and therefore is not suitable for a direct board-level substitution. Choose the compact HVSON version when its land pattern and exposed-pad process are already approved.
Is TJA1042ATK/3/0Z suitable for industrial CAN communication?
The TJA1042ATK/3/0Z is suitable for industrial CAN networks when its 4.5 V to 5.5 V supply, 5 Mbit/s maximum data rate, standby mode, and -40 °C to +150 °C junction-temperature range satisfy the system requirements. Its automotive qualification can benefit industrial equipment used in harsh environments. Add appropriate bus protection and validate EMC performance in the final enclosure and cable configuration.
What are the key specifications of TJA1042ATK/3/0Z that engineers should know?
The TJA1042ATK/3/0Z is a 5 Mbit/s high-speed CAN and CAN FD transceiver with a 4.5 V to 5.5 V supply, 5 V logic interface, low-power standby, bus wake-up capability, and passive behavior when unpowered. It is available in an active automotive AEC-Q100 8-HVSON 3 x 3 mm exposed-pad package rated for -40 °C to +150 °C junction temperature. These parameters define its bus, thermal, and PCB-design envelope.
How should a TJA1042ATK/3/0Z CAN network be laid out?
Route CANH and CANL as a short, balanced differential pair between the TJA1042ATK/3/0Z and the bus connector, keeping them away from switching nodes and unrelated high-current paths. Place the transceiver close to the connector, apply the specified termination arrangement, and connect the exposed pad according to the manufacturer layout guidance. The bus protection network and common-mode components must be selected for the vehicle or industrial transient environment.

داده‌های مرجع مهندسی برای TJA1042ATK/3/0Z — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the TJA1042ATK/3/0Z for an existing 8-HVSON 3 x 3 mm PCB that requires a 5 Mbit/s high-speed CAN or CAN FD interface, a 4.5 V to 5.5 V transceiver supply, standby bus wake-up, passive unpowered behavior, and automotive-grade environmental positioning. The TJA1042TK/3/0Z is the closest same-family HVSON candidate, but its exact interface configuration must be confirmed in the NXP ordering table before substitution. Consider TJA1042TK/3/1 only when its VIO and standby configuration match the target circuit. Do not choose TJA1042AT/3/0Z for a direct footprint replacement because it uses an 8-SO package. The compact HVSON construction also requires an approved exposed-pad land pattern, thermal-via strategy, and assembly process.

مقایسه با جایگزین‌ها

پارامتر این محصول TJA1042TK/3/0Z TJA1042TK/3/1
Package 8-HVSON (3 x 3 mm) 8-HVSON (3 x 3 mm) 8-HVSON (3 x 3 mm)
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors

تفاوت‌های کلیدی

  • Compact automotive CAN interface footprint (در مقابلTJA1042AT/3/0Z)
  • High-speed CAN and CAN FD capability (در مقابلTJA1042TK/3/0Z)
  • Active high-temperature automotive positioning (در مقابلTJA1042TK/3/1)

یادداشت‌های طراحی

Route CANH and CANL as a short, balanced differential pair between the transceiver and connector. Keep the pair away from switching power nodes, high-current returns, oscillators, and unprotected inductive loads. Place the TJA1042ATK/3/0Z near the bus entry and provide the termination and protection components identified by the manufacturer application guidance. This layout minimizes radiated emissions and susceptibility to external fields.

The 8-HVSON package exposes a thermal pad for heat removal, but its effectiveness depends on the PCB copper and via arrangement. Follow the manufacturer land pattern and exposed-pad connection instructions, and place thermal vias where specified without violating assembly or cleanliness requirements. Estimated: actual junction temperature depends on transceiver dissipation, ambient temperature, copper area, via count, and the board's thermal resistance; none of those system values are specified here.

Do not treat TJA1042ATK/3/0Z and TJA1042AT/3/0Z as interchangeable because their package constructions differ. The K ordering code denotes the HVSON 3 x 3 mm form, while the AT ordering code denotes the 8-SO form. Also verify whether SPLIT or VIO behavior is required before approving a family variant. The manufacturer's pin-description and ordering-information tables should control the schematic and layout review.

Provide a clean 5 V transceiver rail within the specified 4.5 V to 5.5 V range and place local decoupling close to the supply pins. Keep converter switching loops and high-current returns away from the CAN traces and transceiver ground path. Validate supply tolerance, startup behavior, standby transitions, and bus wake-up across the complete controller power sequence rather than checking only steady-state operation.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The product listing identifies TJA1042ATK/3/0Z as an automotive AEC-Q100 part. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer.

تاریخ تأیید داده‌ها: 2026-11-14 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

TJA1042ATK/3/0Z datasheet TJA1042ATK/3/0Z pinout TJA1042ATK/3/0Z datasheet pdf TJA1042ATK/3/0Z replacement TJA1042ATK/3/0Z equivalent TJA1042ATK/3/0Z cross reference TJA1042ATK/3/0Z vs TJA1042TK/3/0Z TJA1042ATK/3/0Z HVSON8 footprint NXP TJA1042ATK/3/0Z TJA1042ATK/3/0Z 5Mbps CAN transceiver TJA1042ATK/3/0Z automotive CAN FD TJA1042ATK/3/0Z price TJA1042ATK/3/0Z stock TJA1042ATK/3/0Z application circuit

قطعات و اصطلاحات مرتبط

NXP Semiconductors TJA1042ATK/3/0Z TJA1042TK/3/0Z TJA1042TK/3/1 TJA1042AT/3/0Z TJA1057GTK/3Z CAN transceiver CAN FD Controller Area Network high-speed CAN two-wire differential bus interface IC automotive electronics AEC-Q100 RoHS REACH 8-HVSON HVSON exposed-pad package QFN package family surface-mount package 5 Mbit/s data rate 4.5 V to 5.5 V supply standby bus wake-up passive unpowered behavior EMC performance
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ