NXP Semiconductors

TJA1054AT/M - 125 kBd Single-Wire CAN Transceiver | NXP

MPN: TJA1054AT/M ✓ فعال
5 V Vdss 14-pin SOIC-style gull-wing package Package
حداقل سفارش: 1 |

TJA1054AT/M نمای کلی

NXP Semiconductors TJA1054AT/M is a fault-tolerant, ESD-improved single-wire CAN bus transceiver designed for low-speed automotive communication up to 125 kBd. It operates from a nominal 5 V supply and is packaged in a 14-pin SOIC-style gull-wing package identified by the TJA1054AT/M,518 ordering code. The device interfaces a CAN protocol controller with one physical bus conductor and provides the physical-layer functions required for reliable low-speed CAN communication.

A CAN transceiver is the physical-layer interface between a CAN protocol controller and the bus wiring. The TJA1054AT family belongs to the hierarchy of CAN interface ICs, communication transceivers, interface ICs, and semiconductors. Its single-wire architecture is intended for passenger-car systems operating at or below 125 kBd, where fault-tolerant behavior and ESD protection are important in electrically harsh vehicle environments.

The TJA1054AT is an ESD-improved version of the original TJA1054. According to the NXP TJA1054A data sheet, the principal improvements concern electrostatic-discharge robustness while retaining the operating functions of the earlier device. NXP also identifies the TJA1054AT as pin and downwards compatible with the PCA82C252T and TJA1053T, allowing those components to be replaced while retaining their existing functions.

The TJA1054T is a closely related member of the same device family. NXP states that the TJA1054AT and TJA1054T are interchangeable on the same 14-pin footprint, with the relevant distinction being the AT version's improved ESD characteristics. This relationship makes the TJA1054AT/M particularly useful for maintaining an existing SO14 PCB while improving transient immunity without changing the mechanical land pattern.

Typical uses include single-wire CAN body and comfort networks, vehicle sensor nodes, door modules, lighting controllers, seat controllers, climate-control interfaces, and other low-speed automotive electronics. The transceiver's fault-tolerant design helps maintain communication when the bus has a short to ground or battery, provided the system remains within the device's specified electrical limits and uses the recommended bus protection and termination arrangements.

PCB design should preserve the manufacturer's recommended decoupling and bus-network topology. Place the supply capacitor close to VCC and GND, route CAN wiring as a physically robust network, and apply protection appropriate to the vehicle harness. Because a CAN transceiver communicates through physical-layer signaling rather than a data protocol, the associated controller must support the matching single-wire CAN signaling convention.

This page combines the NXP product description and family data with practical replacement guidance, package compatibility information, and application-oriented design considerations. It helps engineers distinguish a true same-footprint substitute from a merely similar CAN transceiver before committing an existing 14-pin automotive design to a new BOM.

جایگزین‌های drop-in برای TJA1054AT/M — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای TJA1054AT/M (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Product Type, Package, Fault Tolerance, Package Type.

NXP Semiconductors
Product Type: Half CANbus transceiver
Package: 14-SO
NXP Semiconductors
Product Type: Fault-tolerant CAN transceiver
Package: 14-pin SOIC, 3.9 mm body
Fault Tolerance: Fault-tolerant CAN operation
NXP Semiconductors
Product Type: Enhanced fault-tolerant CAN transceiver
Package: 14-pin SO
Package Type: Tape and reel

TJA1054T/N1

✅ جایگزین مستقیم
NXP Semiconductors
📦 14-pin SOIC-style gull-wing package
Fault-tolerant CAN transceiver · 125 kBd · Low-speed passenger-car CAN networks · CANH and CANL differential bus · 14-pin SOIC, 3.9 mm body · Surface mount · Between CAN protocol controller and physical bus wires · Fault-tolerant CAN operation

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

PCA82C252T

✅ جایگزین مستقیم
📦 14-pin SOIC-style gull-wing package
NXP states pin and downwards compatibility with retained functions; TJA1054AT adds improved ESD performance and targets the 125 kBd low-speed use case.

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1053T/N1

✅ جایگزین مستقیم
NXP Semiconductors
📦 14-pin SOIC-style gull-wing package
Half CANbus transceiver · 1 transmit / 1 receive · 4.75 V to 5.25 V · 5 V · Up to 36 V · Controller Area Network (CAN) · 14-SO · 14 pins

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

TLE6254-3G

✅ جایگزین مستقیم
📦 14-pin SOIC-style gull-wing package
Both are fault-tolerant low-speed CAN transceivers supporting operation to 125 kBd; verify pin-level bus and mode behavior against each manufacturer data sheet.

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1055T/3/1J

✅ جایگزین مستقیم
NXP Semiconductors
📦 14-pin SOIC-style gull-wing package
Enhanced fault-tolerant CAN transceiver · 125 kBd · 5 V to 28 V · 5 V, 9 V, 12 V, 15 V, 18 V, 24 V, and 28 V · 3 V · Differential · Differential · Up to 125 kBd in passenger cars

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

TJA1054AT/M مشخصات

Product Type Single-wire CAN bus transceiver
Maximum Data Rate 125 kBd
Nominal Supply Voltage 5 V
Logic Supply Voltage 5 V
Bus Architecture Single-wire CAN
ESD Protection Improved ESD performance
Fault Tolerance Fault-tolerant CAN transceiver
Package Type 14-pin SOIC-style gull-wing package
Number of Terminals 14 terminals
نوع نصب Surface mount
Compatibility Pin and downwards compatible with PCA82C252T and TJA1053T
Target Application Low-speed passenger-car CAN networks
وضعیت RoHS unknown
REACH Status unknown
Lead-Free Status unknown

راهنمای پیکربندی پین TJA1054AT/M 14-pin soic-style gull-wing package

پیکربندی پین برای TJA1054AT/M (پکیج 14-pin soic-style gull-wing package). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 14-pin soic-style gull-wing package برای TJA1054AT/M

داده پین‌آوت تفصیلی موجود نیست برای TJA1054AT/M.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

TJA1054AT/M مناسب است برای 6 کاربردs: Automotive Body Control Networks, Vehicle Door and Seat Modules, Lighting Control Modules, Automotive Sensor Nodes, Climate Control Interfaces, Legacy Automotive PCB Upgrade.

🚗

Automotive Body Control Networks

The TJA1054AT/M fits low-speed single-wire CAN nodes in body-control modules because it operates to 125 kBd from a nominal 5 V supply and provides improved ESD protection. A controller such as a CAN protocol IC communicates through the transceiver, which handles the physical bus interface and fault-tolerant behavior. Its 14-pin SOIC-style package also supports compact automotive electronics designs. The main design consideration is retaining the established single-wire bus topology and validating every connected pin against the NXP data sheet during any replacement.

🚗

Vehicle Door and Seat Modules

Door modules, seat controllers, and related vehicle comfort systems can use the TJA1054AT/M for short-range, low-speed communication over a single-wire CAN network. The 125 kBd maximum rate is appropriate for control and status traffic rather than high-bandwidth vehicle data. Fault-tolerant operation and improved ESD performance add value in a harness environment where connector faults and electrostatic discharge are design concerns. Engineers should verify bus termination, supply decoupling, and every mode-control connection in the manufacturer application information.

💡

Lighting Control Modules

The TJA1054AT/M can connect a lighting controller or distributed lamp module to a low-speed single-wire CAN network. At a maximum rate of 125 kBd, the link is suited to commands, status, and diagnostic signaling rather than streaming data. The transceiver's nominal 5 V operation aligns with conventional automotive logic rails, while improved ESD protection supports robustness in an electronics enclosure connected to vehicle wiring. Validate the selected termination network and inactive-state behavior against the device data sheet.

🧩

Automotive Sensor Nodes

A remote sensor node can use the TJA1054AT/M when its CAN controller communicates over a single-wire bus at rates up to 125 kBd. The device isolates the controller from the physical bus while providing fault-tolerant signal behavior and improved ESD robustness. For nodes connected to long harness wiring, protection, termination, and return-path implementation remain critical system-level considerations. The data sheet's application schematic should be followed closely rather than treating the transceiver as a standalone communications link.

🏭

Climate Control Interfaces

Climate-control gateways and cabin electronics can use the TJA1054AT/M for command exchange over a low-speed single-wire CAN segment. The 125 kBd limit matches supervisory and configuration traffic, and the 14-pin package leaves room for the required logic, wake, and protection circuitry around the transceiver. Improved ESD characteristics are useful near switches, connectors, and external harness wiring. Before layout release, confirm the controller's electrical interface and the transceiver's standby or wake behavior in the official NXP documentation.

🔧

Legacy Automotive PCB Upgrade

The TJA1054AT/M is well suited to an upgrade of an existing 14-pin single-wire CAN design because NXP identifies compatibility with the TJA1054T, PCA82C252T, and TJA1053T. The AT variant adds improved ESD performance while preserving the established physical interface. This enables a focused redesign without moving to a different footprint or changing the bus architecture. A complete engineering review should still compare absolute maximum ratings, mode pins, supply sequencing, and timing because compatibility statements do not waive application-level verification.

خلاصه محصولات پیشنهادی

TJA1054T Same-footprint CAN transceiver family member استفاده‌شده در: Automotive Body Control Networks, Vehicle Door and Seat Modules, Lighting Control Modules, Automotive Sensor Nodes, Climate Control Interfaces, Legacy Automotive PCB Upgrade TJA1053T Pin-compatible predecessor identified by NXP استفاده‌شده در: Automotive Body Control Networks, Lighting Control Modules, Climate Control Interfaces, Legacy Automotive PCB Upgrade PCA82C252T Pin-compatible predecessor identified by NXP استفاده‌شده در: Vehicle Door and Seat Modules, Automotive Sensor Nodes, Legacy Automotive PCB Upgrade
What is the TJA1054AT/M?
The TJA1054AT/M is an NXP Semiconductors fault-tolerant, ESD-improved single-wire CAN transceiver rated for low-speed communication up to 125 kBd. It operates from a nominal 5 V supply and uses a 14-pin SOIC-style gull-wing package. According to the NXP TJA1054A data sheet, the device serves as the physical-layer interface between a CAN protocol controller and the physical bus wiring.
Where can I download the TJA1054AT datasheet PDF?
The official TJA1054A data sheet is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1054A.pdf. It covers the TJA1054AT family, including the TJA1054AT/M ordering information, electrical characteristics, application information, and compatibility with the PCA82C252T and TJA1053T. Use the NXP document as the controlling reference for limits, test conditions, and package drawings.
What is the TJA1054AT/M pinout?
The TJA1054AT/M uses a 14-pin SOIC-style package, but a complete pin-by-pin assignment is not reproduced on this page. Use the pin-description table and package drawing in the official NXP TJA1054A data sheet when assigning PCB tracks. The manufacturer identifies the AT and T versions as interchangeable on the same footprint and states that the AT version is pin and downwards compatible with the PCA82C252T and TJA1053T.
Can the TJA1054AT/M replace the TJA1054T?
Yes, the TJA1054AT/M can serve as a same-footprint replacement for the TJA1054T in an appropriate design. NXP identifies both devices as compatible, and the TJA1054AT adds improved ESD performance relative to the earlier TJA1054. Because the AT version retains the functions of the T version, existing PCB routing can be retained, but the replacement should still be checked against the manufacturer datasheet for operating limits and qualification requirements.
Can the TJA1054AT/M replace the PCA82C252T or TJA1053T?
Yes, NXP states that the TJA1054AT and TJA1054T are pin and downwards compatible with the PCA82C252T and TJA1053T, with retention of all functions. This makes the TJA1054AT/M a candidate for an existing 14-pin design. Before substitution, verify that the circuit does not depend on a feature or electrical limit outside the TJA1054A data sheet, particularly for high-speed operation or nonstandard bus terminations.
What is the difference between TJA1054AT/M and TJA1054T?
The TJA1054AT/M is the ESD-improved AT version of the TJA1054T, while both retain the same 14-pin family footprint and core transceiver functions. The key distinction is improved electrostatic-discharge robustness in the AT version. NXP describes the TJA1054A as the ESD-improved version of the TJA1054, making the AT device preferable when enhanced transient immunity is more important than preserving an older non-AT component.
Where can I buy TJA1054AT/M online?
Use the Request a Quote form on this page to request TJA1054AT/M availability, current lead time, minimum order quantity, and shipping options. The form lets the request be associated with the exact TJA1054AT/M ordering code rather than a broader TJA1054A family designation. Confirm the orderable suffix and delivery packaging when the quotation is returned.
What is the price of TJA1054AT/M?
Current TJA1054AT/M pricing is shown through the Request a Quote form on this page. The quotation should specify the exact MPN, quantity, currency, packaging, and delivery terms. Because automotive inventory can move through multiple order codes, avoid approving a quotation for the generic TJA1054AT or TJA1054T family designation when the released BOM requires TJA1054AT/M,518.
What is the lead time for TJA1054AT/M?
The current lead time for TJA1054AT/M should be requested through the Request a Quote form on this page. Include the required annual usage, forecast horizon, and approved package or reel code in the request. This avoids confusion with TJA1054AT variants that differ only in their ordering suffix and may be stocked or manufactured on separate schedules.
Is TJA1054AT/M in stock?
Current stock status for TJA1054AT/M is available through the Request a Quote form on this page. Submit the required quantity and, when applicable, the date code, packaging, and quality requirements. A confirmation of the exact ordering code is important because TJA1054AT family members are also identified by related suffixes such as ,512 and ,518.
When should I choose the TJA1054AT/M over the TJA1054T?
Choose the TJA1054AT/M over the TJA1054T when improved ESD robustness is important and the circuit can use the TJA1054AT family behavior. Both devices occupy the same 14-pin footprint, so the decision is primarily electrical and qualification-related rather than mechanical. Confirm the replacement against the manufacturer data sheet, especially when a product has a previously validated TJA1054T implementation.
Is the TJA1054AT/M suitable for low-speed automotive CAN?
The TJA1054AT/M is specifically intended for low-speed single-wire CAN applications up to 125 kBd. NXP describes the TJA1054A as an interface between a CAN protocol controller and the physical bus wires, primarily for passenger-car systems. Its suitability therefore depends on using a compatible single-wire CAN network and a controller whose physical signaling matches the TJA1054AT interface.
What is the best drop-in replacement for TJA1054AT/M?
The TJA1054T is the clearest same-footprint replacement because NXP identifies the AT and T versions as interchangeable and both use the 14-pin family package. The TJA1054AT/M adds improved ESD characteristics. For cross-brand options, validate the exact pin mapping, package, single-wire CAN behavior, electrical limits, and bus topology in the candidate manufacturer's data sheet before treating it as a drop-in replacement.
Is the TJA1054AT/M the same as the TLE6254-3G?
The TJA1054AT/M and TLE6254-3G are both described as low-speed, fault-tolerant CAN transceivers, but they are not automatically interchangeable. A valid replacement must also have the same 14-pin footprint, matching pin functions, compatible single-wire bus behavior, and acceptable electrical limits. Review the official data sheets for both devices and compare each connected pin before approving the substitution.
What are the key specifications of TJA1054AT/M that engineers should know?
The key engineering facts are a maximum data rate of 125 kBd, nominal 5 V operation, single-wire CAN bus architecture, fault-tolerant operation, improved ESD protection, and a 14-pin SOIC-style gull-wing package. NXP also states pin and downwards compatibility with the PCA82C252T and TJA1053T. These characteristics place the device in low-speed passenger-car CAN systems rather than high-speed differential CAN networks.

داده‌های مرجع مهندسی برای TJA1054AT/M — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the TJA1054AT/M for a 5 V, low-speed single-wire CAN design that requires fault tolerance, improved ESD performance, and a 14-pin SOIC-style footprint. The TJA1054T is the direct alternative when a design does not need the AT version's improved ESD characteristics; both remain usable in the same 125 kBd class. NXP's documented pin and downwards compatibility makes the TJA1054AT/M attractive for upgrading boards based on the PCA82C252T or TJA1053T. The TLE6254-3G is a cross-brand option for evaluation when its pin functions, mode behavior, protection limits, and bus-network requirements have been checked against the NXP device. The TJA1055T family should be selected only after its bus architecture and connected-pin assignments are confirmed. For every candidate, verify the controller interface, termination network, supply sequencing, automotive temperature requirements, and transient ratings before releasing a production BOM.

مقایسه با جایگزین‌ها

پارامتر این محصول TJA1054T PCA82C252T TJA1053T TLE6254-3G
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors Infineon Technologies
Package 14-pin SOIC-style gull-wing package 14-pin SOIC-style gull-wing package 14-pin SOIC-style gull-wing package 14-pin SOIC-style gull-wing package 14-pin SOIC-style gull-wing package
Product Type Fault-tolerant single-wire CAN transceiver Single-wire CAN transceiver CAN transceiver Single-wire CAN transceiver Fault-tolerant low-speed CAN transceiver
Bus Architecture Single-wire CAN Single-wire CAN Single-wire CAN Single-wire CAN Single-wire CAN
Fault Tolerance Yes Yes Yes Yes Yes
Manufacturer Compatibility Pin and downwards compatible with PCA82C252T and TJA1053T Interchangeable same-family alternative NXP-identified compatible predecessor NXP-identified compatible predecessor Cross-brand pin and behavior verification required
Terminal Count 14 terminals 14 terminals 14 terminals 14 terminals 14 terminals

تفاوت‌های کلیدی

  • Improved ESD robustness within the same transceiver family (در مقابلTJA1054T)
  • Manufacturer-documented retained-function compatibility (در مقابلPCA82C252T)
  • Direct upgrade path for TJA1053T-based designs (در مقابلTJA1053T)
  • Cross-brand low-speed fault-tolerant alternative (در مقابلTLE6254-3G)

یادداشت‌های طراحی

Place the transceiver's supply-decoupling capacitor as close as practical to the VCC and ground pins, and keep the CAN trace short and physically robust. The bus conductor is sensitive to automotive harness transients, so route it away from switching nodes and maintain a continuous ground reference. Use the NXP application schematic as the basis for component placement and bus protection rather than adding arbitrary series components that change termination behavior.

Do not treat a CAN transceiver as interchangeable with a high-speed differential CAN device merely because both use a 14-pin package. The TJA1054AT/M is a single-wire, 125 kBd-class device, while other CAN families may use two differential bus conductors and different mode or standby logic. Verify pin names, bus topology, wake behavior, and supply limits against each candidate's official data sheet before revising an existing PCB.

Design the single-wire CAN network with the termination and protection arrangement specified by NXP. Automotive wiring can experience faults, shorts, and electrostatic discharge, so the transceiver's fault tolerance must be complemented by appropriate harness protection. Keep high-current relays, motor drivers, and inductive switching loops separated from the bus and controller ground paths to reduce conducted and radiated noise.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The available manufacturer descriptions identify the device as intended for passenger-car applications but do not state a specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.

تاریخ تأیید داده‌ها: 2026-11-18 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

tja1054at datasheet tja1054at ic datasheet nxp tja1054at TJA1054AT/M datasheet pdf TJA1054AT/M pinout TJA1054AT/M equivalent TJA1054AT/M replacement TJA1054AT/M cross reference TJA1054AT/M SO14 pinout TJA1054AT/M automotive CAN TJA1054AT/M price TJA1054AT/M stock

قطعات و اصطلاحات مرتبط

NXP Semiconductors TJA1054AT/M TJA1054AT TJA1054T TJA1053T PCA82C252T TLE6254-3G TJA1055T/3/1J CAN transceiver single-wire CAN fault-tolerant CAN CAN protocol controller interface IC communication transceiver semiconductor 125 kBd nominal 5 V supply ESD protection SOIC-14 gull-wing package surface mount SMD automotive electronics passenger-car network
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ