TJA1054AT/M - 125 kBd Single-Wire CAN Transceiver | NXP
Артикул: TJA1054AT/M ✓ АктивенTJA1054AT/M Обзор
A CAN transceiver is the physical-layer interface between a CAN protocol controller and the bus wiring. The TJA1054AT family belongs to the hierarchy of CAN interface ICs, communication transceivers, interface ICs, and semiconductors. Its single-wire architecture is intended for passenger-car systems operating at or below 125 kBd, where fault-tolerant behavior and ESD protection are important in electrically harsh vehicle environments.
The TJA1054AT is an ESD-improved version of the original TJA1054. According to the NXP TJA1054A data sheet, the principal improvements concern electrostatic-discharge robustness while retaining the operating functions of the earlier device. NXP also identifies the TJA1054AT as pin and downwards compatible with the PCA82C252T and TJA1053T, allowing those components to be replaced while retaining their existing functions.
The TJA1054T is a closely related member of the same device family. NXP states that the TJA1054AT and TJA1054T are interchangeable on the same 14-pin footprint, with the relevant distinction being the AT version's improved ESD characteristics. This relationship makes the TJA1054AT/M particularly useful for maintaining an existing SO14 PCB while improving transient immunity without changing the mechanical land pattern.
Typical uses include single-wire CAN body and comfort networks, vehicle sensor nodes, door modules, lighting controllers, seat controllers, climate-control interfaces, and other low-speed automotive electronics. The transceiver's fault-tolerant design helps maintain communication when the bus has a short to ground or battery, provided the system remains within the device's specified electrical limits and uses the recommended bus protection and termination arrangements.
PCB design should preserve the manufacturer's recommended decoupling and bus-network topology. Place the supply capacitor close to VCC and GND, route CAN wiring as a physically robust network, and apply protection appropriate to the vehicle harness. Because a CAN transceiver communicates through physical-layer signaling rather than a data protocol, the associated controller must support the matching single-wire CAN signaling convention.
This page combines the NXP product description and family data with practical replacement guidance, package compatibility information, and application-oriented design considerations. It helps engineers distinguish a true same-footprint substitute from a merely similar CAN transceiver before committing an existing 14-pin automotive design to a new BOM.
Аналоги без доработки для TJA1054AT/M — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с TJA1054AT/M (тот же форм-фактор и посадочное место) — отличается по Product Type, Package, Fault Tolerance, Package Type.
TJA1054T/N1
✅ Прямая заменаУточнить цену
Открыть даташит →PCA82C252T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TJA1053T/N1
✅ Прямая заменаУточнить цену
Открыть даташит →TLE6254-3G
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TJA1055T/3/1J
✅ Прямая заменаУточнить цену
Открыть даташит →TJA1054AT/M Характеристики
| Product Type | Single-wire CAN bus transceiver |
| Maximum Data Rate | 125 kBd |
| Nominal Supply Voltage | 5 V |
| Logic Supply Voltage | 5 V |
| Bus Architecture | Single-wire CAN |
| ESD Protection | Improved ESD performance |
| Fault Tolerance | Fault-tolerant CAN transceiver |
| Package Type | 14-pin SOIC-style gull-wing package |
| Number of Terminals | 14 terminals |
| Тип монтажа | Surface mount |
| Compatibility | Pin and downwards compatible with PCA82C252T and TJA1053T |
| Target Application | Low-speed passenger-car CAN networks |
| Статус RoHS | unknown |
| REACH Status | unknown |
| Lead-Free Status | unknown |
Руководство по цоколевке TJA1054AT/M в корпусе 14-pin soic-style gull-wing package
Цоколевка для TJA1054AT/M (корпус 14-pin soic-style gull-wing package). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для TJA1054AT/M.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
TJA1054AT/M подходит для 6 применениеs: Automotive Body Control Networks, Vehicle Door and Seat Modules, Lighting Control Modules, Automotive Sensor Nodes, Climate Control Interfaces, Legacy Automotive PCB Upgrade.
Automotive Body Control Networks
The TJA1054AT/M fits low-speed single-wire CAN nodes in body-control modules because it operates to 125 kBd from a nominal 5 V supply and provides improved ESD protection. A controller such as a CAN protocol IC communicates through the transceiver, which handles the physical bus interface and fault-tolerant behavior. Its 14-pin SOIC-style package also supports compact automotive electronics designs. The main design consideration is retaining the established single-wire bus topology and validating every connected pin against the NXP data sheet during any replacement.
Рекомендуется
Vehicle Door and Seat Modules
Door modules, seat controllers, and related vehicle comfort systems can use the TJA1054AT/M for short-range, low-speed communication over a single-wire CAN network. The 125 kBd maximum rate is appropriate for control and status traffic rather than high-bandwidth vehicle data. Fault-tolerant operation and improved ESD performance add value in a harness environment where connector faults and electrostatic discharge are design concerns. Engineers should verify bus termination, supply decoupling, and every mode-control connection in the manufacturer application information.
Рекомендуется
Lighting Control Modules
The TJA1054AT/M can connect a lighting controller or distributed lamp module to a low-speed single-wire CAN network. At a maximum rate of 125 kBd, the link is suited to commands, status, and diagnostic signaling rather than streaming data. The transceiver's nominal 5 V operation aligns with conventional automotive logic rails, while improved ESD protection supports robustness in an electronics enclosure connected to vehicle wiring. Validate the selected termination network and inactive-state behavior against the device data sheet.
Рекомендуется
Automotive Sensor Nodes
A remote sensor node can use the TJA1054AT/M when its CAN controller communicates over a single-wire bus at rates up to 125 kBd. The device isolates the controller from the physical bus while providing fault-tolerant signal behavior and improved ESD robustness. For nodes connected to long harness wiring, protection, termination, and return-path implementation remain critical system-level considerations. The data sheet's application schematic should be followed closely rather than treating the transceiver as a standalone communications link.
Рекомендуется
Climate Control Interfaces
Climate-control gateways and cabin electronics can use the TJA1054AT/M for command exchange over a low-speed single-wire CAN segment. The 125 kBd limit matches supervisory and configuration traffic, and the 14-pin package leaves room for the required logic, wake, and protection circuitry around the transceiver. Improved ESD characteristics are useful near switches, connectors, and external harness wiring. Before layout release, confirm the controller's electrical interface and the transceiver's standby or wake behavior in the official NXP documentation.
Рекомендуется
Legacy Automotive PCB Upgrade
The TJA1054AT/M is well suited to an upgrade of an existing 14-pin single-wire CAN design because NXP identifies compatibility with the TJA1054T, PCA82C252T, and TJA1053T. The AT variant adds improved ESD performance while preserving the established physical interface. This enables a focused redesign without moving to a different footprint or changing the bus architecture. A complete engineering review should still compare absolute maximum ratings, mode pins, supply sequencing, and timing because compatibility statements do not waive application-level verification.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TJA1054AT/M — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TJA1054T | PCA82C252T | TJA1053T | TLE6254-3G |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Infineon Technologies |
| Package | 14-pin SOIC-style gull-wing package | 14-pin SOIC-style gull-wing package | 14-pin SOIC-style gull-wing package | 14-pin SOIC-style gull-wing package | 14-pin SOIC-style gull-wing package |
| Product Type | Fault-tolerant single-wire CAN transceiver | Single-wire CAN transceiver | CAN transceiver | Single-wire CAN transceiver | Fault-tolerant low-speed CAN transceiver |
| Bus Architecture | Single-wire CAN | Single-wire CAN | Single-wire CAN | Single-wire CAN | Single-wire CAN |
| Fault Tolerance | Yes | Yes | Yes | Yes | Yes |
| Manufacturer Compatibility | Pin and downwards compatible with PCA82C252T and TJA1053T | Interchangeable same-family alternative | NXP-identified compatible predecessor | NXP-identified compatible predecessor | Cross-brand pin and behavior verification required |
| Terminal Count | 14 terminals | 14 terminals | 14 terminals | 14 terminals | 14 terminals |
Ключевые отличия
- Improved ESD robustness within the same transceiver family (против TJA1054T)
- Manufacturer-documented retained-function compatibility (против PCA82C252T)
- Direct upgrade path for TJA1053T-based designs (против TJA1053T)
- Cross-brand low-speed fault-tolerant alternative (против TLE6254-3G)
Заметки по проектированию
Place the transceiver's supply-decoupling capacitor as close as practical to the VCC and ground pins, and keep the CAN trace short and physically robust. The bus conductor is sensitive to automotive harness transients, so route it away from switching nodes and maintain a continuous ground reference. Use the NXP application schematic as the basis for component placement and bus protection rather than adding arbitrary series components that change termination behavior.
Do not treat a CAN transceiver as interchangeable with a high-speed differential CAN device merely because both use a 14-pin package. The TJA1054AT/M is a single-wire, 125 kBd-class device, while other CAN families may use two differential bus conductors and different mode or standby logic. Verify pin names, bus topology, wake behavior, and supply limits against each candidate's official data sheet before revising an existing PCB.
Design the single-wire CAN network with the termination and protection arrangement specified by NXP. Automotive wiring can experience faults, shorts, and electrostatic discharge, so the transceiver's fault tolerance must be complemented by appropriate harness protection. Keep high-current relays, motor drivers, and inductive switching loops separated from the bus and controller ground paths to reduce conducted and radiated noise.
Информация о соответствии
The available manufacturer descriptions identify the device as intended for passenger-car applications but do not state a specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.