NXP Semiconductors

TJA1055T/3/CM - 125 kBd Fault-Tolerant CAN | NXP

MPN: TJA1055T/3/CM ✓ فعال
5 V to 28 V Vdss 14-pin SOIC Package
حداقل سفارش: 1 |

TJA1055T/3/CM نمای کلی

The NXP TJA1055T/3/CM is an enhanced fault-tolerant CAN transceiver supporting data rates up to 125 kBd in a 14-pin SOIC package. It operates from a 5 V to 28 V supply range, supports 9 V, 12 V, 15 V, 18 V, and 24 V battery configurations, and provides sleep and standby operating modes for reduced system power. The device is supplied in tape-and-reel packaging and is identified as an automotive AEC-Q100 transceiver.

A CAN transceiver is the physical-layer interface between a CAN protocol controller and the differential CAN bus. The TJA1055T/3 family combines transmit and receive functions, bus-fault detection, and fault-tolerant behavior in one interface IC. This hierarchy connects the device to CAN controllers, vehicle networking systems, industrial communication equipment, and embedded electronic control units.

Key features include differential receive and transmit capability, fault-tolerant operation, a maximum bus speed of 125 kBd, and low-power sleep and standby modes. The 5 V to 28 V supply range accommodates conventional automotive battery systems, while the AEC-Q100 designation identifies suitability for automotive qualification requirements. Its 14-pin SOIC format supports conventional surface-mount assembly and compact controller-area-network routing.

The transceiver is intended for low-speed CAN communication and provides the electrical interface between digital controller logic and the physical bus. Differential signaling improves signal integrity and common-mode rejection on the CANH and CANL conductors. Fault-tolerant circuitry is intended to maintain communication when bus faults occur, although system behavior still depends on termination, wiring, grounding, and the selected network topology.

Typical applications include passenger-car body and comfort electronics, automotive control modules, low-speed diagnostic equipment, industrial CAN controllers, and embedded systems that connect a CAN controller to a two-wire bus. The sleep and standby functions are particularly useful where modules must reduce current consumption while retaining controlled bus connectivity.

Place the transceiver close to the bus connector and CAN controller, route CANH and CANL as a tightly coupled differential pair, and provide the termination required by the network. Keep the ground reference and power-return routing consistent with the bus structure to minimize common-mode effects. Confirm device pin assignments in the NXP datasheet before assigning connector, controller, and supply connections.

This product page combines the TJA1055T/3/CM technical identity with verified package, speed, supply, mode, and automotive information. It also provides application guidance, drop-in comparison candidates, and practical PCB considerations to support faster component selection and implementation.

جایگزین‌های drop-in برای TJA1055T/3/CM — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای TJA1055T/3/CM (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Product Type, Primary Application, Fault Tolerance, Receive Capability.

NXP Semiconductors
Package: SO14, 14 pins
Product Type: Fault-tolerant single-wire CAN transceiver
Primary Application: Low-speed passenger-car CAN networks
NXP Semiconductors
Package: Plastic small outline package
Primary Application: Low-speed passenger-car CAN networks
NXP Semiconductors
Package: 14-pin SO
Receive Capability: Differential

TJA1054AT

✅ جایگزین مستقیم
NXP Semiconductors
📦 14-pin SOIC
Fault-tolerant single-wire CAN transceiver · NXP Semiconductors · 125 kBd · Single-wire CAN · Protocol controller to physical bus-wire interface · ElectroStatic Discharge improved version of TJA1054 · Fault-tolerant CAN operation · SO14, 14 pins

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

TJA1054AT

✅ جایگزین مستقیم
NXP Semiconductors
📦 14-pin SOIC
Fault-tolerant single-wire CAN transceiver · NXP Semiconductors · 125 kBd · Single-wire CAN · Protocol controller to physical bus-wire interface · ElectroStatic Discharge improved version of TJA1054 · Fault-tolerant CAN operation · SO14, 14 pins

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

TJA1055T/3/1

✅ جایگزین مستقیم
NXP Semiconductors
📦 14-pin SOIC
Enhanced fault-tolerant CAN transceiver · 125 kBd · Supported · 3 V · SSMC wafer fab or ICN8 wafer fab · Plastic small outline package · 14 leads · 3.9 mm

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

TJA1055T/3/1J

✅ جایگزین مستقیم
NXP Semiconductors
📦 14-pin SOIC
Enhanced fault-tolerant CAN transceiver · 125 kBd · 5 V to 28 V · 5 V, 9 V, 12 V, 15 V, 18 V, 24 V, and 28 V · 3 V · Differential · Differential · Up to 125 kBd in passenger cars

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

TJA1055T/3/C-T

✅ جایگزین مستقیم
📦 14-pin SOIC
Same fault-tolerant CAN function and 125 kBd class; ordering code denotes the surface-mount shipping form

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1055T/3/CM مشخصات

Product Type Enhanced fault-tolerant CAN transceiver
Maximum Data Rate 125 kBd
Supply Voltage Range 5 V to 28 V
Supported Vehicle Supply Levels 9 V, 12 V, 15 V, 18 V, and 24 V
Power Modes Sleep and standby
Bus Interface Differential CANH and CANL
Transmit Capability Differential CAN transmit
Receive Capability Differential CAN receive
Fault Tolerance Enhanced fault-tolerant operation
Primary Application Low-speed passenger-car CAN communication
بسته‌بندی 14-pin SOIC
Shipping Package Tape and reel
Automotive Qualification AEC-Q100
Pin-to-Pin Compatibility Compatible with TJA1054 and TJA1054A

راهنمای پیکربندی پین TJA1055T/3/CM tape and reel

پیکربندی پین برای TJA1055T/3/CM (پکیج tape and reel). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج tape and reel برای TJA1055T/3/CM

داده پین‌آوت تفصیلی موجود نیست برای TJA1055T/3/CM.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

TJA1055T/3/CM مناسب است برای 6 کاربردs: Automotive Body Control Modules, Vehicle Comfort and Convenience Systems, Low-Speed Automotive Diagnostics, Industrial CAN Control Equipment, Embedded CAN Sensor Gateways, Automotive Infotainment Communication.

🚗

Automotive Body Control Modules

The TJA1055T/3/CM suits body and comfort-control modules that communicate over a low-speed CAN bus at up to 125 kBd. Its differential transceiver functions connect a CAN controller to the CANH and CANL conductors, while enhanced fault-tolerant behavior helps maintain bus operation when wiring faults occur. The 5 V to 28 V supply range supports common vehicle battery environments, and the 14-pin SOIC package supports compact surface-mount assemblies. Designers should route CANH and CANL as a coupled pair and follow the network termination requirements defined by the CAN system architecture.

🚗

Vehicle Comfort and Convenience Systems

The TJA1055T/3/CM can connect door, lighting, climate, seat, or convenience controllers to a 125 kBd CAN network. Low-speed CAN is appropriate for distributed body functions where deterministic control messages and diagnostic communication matter more than very high bandwidth. The device combines differential transmit and receive functions with sleep and standby operating modes, allowing modules to reduce consumption when appropriate. Its AEC-Q100 identification supports automotive design qualification workflows, while fault-tolerant operation is valuable in wiring environments where transient or persistent bus faults must be handled.

🚗

Low-Speed Automotive Diagnostics

The TJA1055T/3/CM is suitable for diagnostic interfaces that exchange service information with vehicle modules over a 125 kBd CAN bus. The physical-layer device connects the diagnostic controller to the differential bus while providing fault detection and fault-tolerant communication behavior. A 5 V to 28 V operating range accommodates automotive supply conditions, and the sleep and standby modes help manage inactive diagnostic equipment. PCB implementation should minimize loop area around CANH and CANL and use the termination arrangement required by the diagnostic network configuration.

🏭

Industrial CAN Control Equipment

The TJA1055T/3/CM can provide the physical interface for industrial controllers operating a low-speed CAN network at 125 kBd. Its differential receive and transmit functions are appropriate for connecting a protocol controller to devices distributed over a two-wire bus. Although primarily described for passenger-car communication, the electrical interface can serve compatible industrial control systems. The 5 V to 28 V supply range offers design flexibility, while sleep and standby modes can reduce consumption in intermittently active equipment. Validate EMC, grounding, fault behavior, and termination against the final industrial installation.

🧩

Embedded CAN Sensor Gateways

The TJA1055T/3/CM can serve as the CAN interface within embedded gateways that collect sensor data or distribute commands to remote modules. A 125 kBd CAN bus provides sufficient bandwidth for modest message rates while supporting a simple two-wire physical network. The transceiver’s differential signaling, fault-tolerant operation, and low-power modes are useful in distributed installations where wiring faults or inactive nodes may affect reliability. The controller interface and logic-level supply arrangement must be checked against the selected variant before implementation, and bus termination should follow the network topology.

📱

Automotive Infotainment Communication

The TJA1055T/3/CM can connect an infotainment or cabin controller to a low-speed CAN segment carrying status and control messages up to 125 kBd. Differential transmit and receive functions provide the physical interface between the host controller and CANH/CANL wiring, while sleep and standby modes help manage power in parked or inactive states. The 14-pin SOIC package is compatible with standard automotive PCB assembly methods, and AEC-Q100 identification supports automotive qualification. System engineers must still verify controller timing, supply sequencing, bus loading, and termination for the selected vehicle network.

خلاصه محصولات پیشنهادی

TJA1054 Documented pin-to-pin-compatible CAN transceiver استفاده‌شده در: Automotive Body Control Modules, Low-Speed Automotive Diagnostics, Embedded CAN Sensor Gateways TJA1054A Documented pin-to-pin-compatible CAN transceiver استفاده‌شده در: Automotive Body Control Modules, Vehicle Comfort and Convenience Systems, Industrial CAN Control Equipment, Automotive Infotainment Communication TJA1055T/3/C-T Same-family surface-mount CAN transceiver استفاده‌شده در: Vehicle Comfort and Convenience Systems, Industrial CAN Control Equipment TJA1055T/3/1 NXP Semiconductors استفاده‌شده در: Low-Speed Automotive Diagnostics, Embedded CAN Sensor Gateways TJA1055T/3/1J NXP Semiconductors استفاده‌شده در: Automotive Infotainment Communication
What is the TJA1055T/3/CM?
The TJA1055T/3/CM is a NXP enhanced fault-tolerant CAN transceiver for low-speed communication up to 125 kBd. According to the NXP TJA1055 datasheet, it is the physical-layer interface between a CAN protocol controller and the differential CAN bus wires. The device provides differential transmit and receive functions, fault-tolerant operation, and low-power sleep and standby modes in a 14-pin SOIC package.
What is the maximum CAN data rate of TJA1055T/3/CM?
The TJA1055T/3/CM supports CAN communication rates up to 125 kBd. The NXP TJA1055 datasheet identifies the device as a low-speed CAN transceiver intended primarily for passenger-car networks. Its 125 kBd limit makes it suitable for body, comfort, diagnostic, and other low-bandwidth vehicle systems, but not for high-speed CAN networks operating above that rate.
What is the supply voltage range of TJA1055T/3/CM?
The TJA1055T/3/CM operates from 5 V to 28 V and supports 9 V, 12 V, 15 V, 18 V, and 24 V vehicle supply environments. According to the NXP TJA1055 datasheet, this range accommodates conventional automotive battery systems. Confirm that the selected power mode, external components, and transceiver variant satisfy the voltage requirements of the complete module.
Where can I download the TJA1055T/3/CM datasheet PDF?
The official TJA1055 datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1055.pdf. Use the pin-description table, application schematic, electrical characteristics, and package drawing when assigning pins and calculating the CAN network. The product page for the broader TJA1055T family is also available through NXP's manufacturer site.
Where can I find the TJA1055T/3/CM pinout?
The TJA1055T/3/CM pinout is shown in the NXP TJA1055 datasheet under the package and pin-description information for the 14-pin SOIC. Use the package drawing to confirm pin 1 orientation and each CAN, control, supply, and ground connection before PCB routing. The 14-pin package drawing also provides the land-pattern dimensions required for a compatible footprint.
Is the TJA1055T/3/CM suitable for automotive applications?
The TJA1055T/3/CM is suitable for automotive communication applications because it supports vehicle supply levels from 5 V to 28 V, operates up to 125 kBd, and is identified as an AEC-Q100 transceiver. The NXP TJA1055 datasheet also describes fault-tolerant CAN operation. Final qualification still depends on the module supplier's production, environmental, and end-system requirements.
Can TJA1054 replace TJA1055T/3/CM?
The TJA1054 is a documented pin-to-pin-compatible alternative to the TJA1055 family, according to the NXP TJA1055 datasheet. Its suitability depends on the specific variant, supply arrangement, fault requirements, and low-speed CAN performance needed by the design. Before substitution, compare the complete electrical characteristics and verify the exact 14-pin footprint rather than relying only on physical compatibility.
TJA1055T/3/CM vs TJA1054A: which is better for a low-speed CAN bus?
The TJA1055T/3/CM is preferable when enhanced fault-tolerant behavior and the documented 5 V to 28 V operating range are priorities. The NXP datasheet states that the TJA1055 is pin-to-pin compatible with both TJA1054 and TJA1054A, making them useful upgrade paths. The final choice should also consider the exact transceiver variant, power-mode requirements, and the vehicle voltage environment.
When should I choose TJA1055T/3/CM over TJA1054?
Choose TJA1055T/3/CM when the design benefits from enhanced fault-tolerant CAN operation, low-power sleep or standby operation, and operation across a 5 V to 28 V supply range. Choose the TJA1054 when its electrical characteristics meet the system requirements and a lower-cost implementation is justified. Because the devices are documented as pin-to-pin compatible, PCB changes are not normally required.
What is the best drop-in replacement for TJA1055T/3/CM?
The strongest documented drop-in candidates are the TJA1054 and TJA1054A because the NXP TJA1055 datasheet explicitly states pin-to-pin compatibility. The TJA1055T/3/C-T is another same-family orderable variant with the same SOIC interface. Confirm voltage ratings, data rate, fault behavior, sleep or standby requirements, and package drawing before approving any replacement.
What can replace TJA1055T/3/CM?
The TJA1055T/3/CM can be replaced by the TJA1054 or TJA1054A when their electrical characteristics satisfy the complete design and the 14-pin footprint remains unchanged. NXP documents pin-to-pin compatibility for both devices. A replacement should still be checked for exact supply range, maximum CAN rate, transceiver operating modes, automotive qualification, and component availability.
Is TJA1055T/3/CM the same as TJA1055T/3/C-T?
The TJA1055T/3/CM and TJA1055T/3/C-T are orderable forms of the same TJA1055T/3 family and use the 14-pin SOIC interface. The TJA1055T/3/C-T listing identifies it as a fault-tolerant CAN transceiver. Verify the exact shipping format, temperature or automotive ordering suffix, and ordering code against the NXP product documentation before treating the parts as interchangeable.
Where can I buy TJA1055T/3/CM and request a quote?
Use the Request a Quote form on this page to request TJA1055T/3/CM pricing, stock confirmation, and lead time. Quote requests should include the exact TJA1055T/3/CM orderable designation, required quantity, and whether tape-and-reel packaging is required. Current commercial terms should be confirmed through the form because inventory and lead time can change.
What is the price of TJA1055T/3/CM?
The current commercial price for TJA1055T/3/CM should be requested through the Request a Quote form on this page. Submit the exact part number, order quantity, and required packaging details to obtain current pricing and availability. The structured pricing fields are intended for qualification and purchasing workflows, while the quote form provides the latest commercial response.
What is the lead time and stock status for TJA1055T/3/CM?
Current stock and lead time for TJA1055T/3/CM should be confirmed through the Request a Quote form on this page. Include the requested quantity, annual usage, and whether the order is for evaluation or production. This provides a direct purchasing channel for an exact-match 14-pin SOIC automotive CAN transceiver without relying on potentially stale inventory information.
What are the key specifications of TJA1055T/3/CM that engineers should know?
The TJA1055T/3/CM is a 14-pin SOIC CAN transceiver rated for 125 kBd operation with a 5 V to 28 V supply range. Its notable features include differential CAN transmit and receive, enhanced fault tolerance, sleep and standby modes, and AEC-Q100 identification. The NXP datasheet also confirms pin-to-pin compatibility with TJA1054 and TJA1054A families.

داده‌های مرجع مهندسی برای TJA1055T/3/CM — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the TJA1055T/3/CM for a 125 kBd vehicle CAN network that benefits from enhanced fault-tolerant operation, sleep and standby modes, and a 5 V to 28 V supply range. Select TJA1054 or TJA1054A when their electrical characteristics satisfy the design and their documented pin-to-pin compatibility makes a PCB-preserving replacement preferable. Use TJA1055T/3/1 or TJA1055T/3/1J when the required 3 V VIO configuration and sourcing arrangement match the controller interface. TJA1055T/3/C-T is appropriate for the same-family interface when its ordering and shipping attributes meet the assembly plan. In every case, verify the exact orderable code, logic-level supply requirements, bus rate, fault behavior, termination, and 14-pin SOIC footprint before approval.

مقایسه با جایگزین‌ها

پارامتر این محصول TJA1054 TJA1054A TJA1055T/3/1 TJA1055T/3/1J TJA1055T/3/C-T
Package 14-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC 14-pin SOIC
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Product Type Enhanced fault-tolerant CAN transceiver CAN transceiver CAN transceiver Enhanced fault-tolerant CAN transceiver Enhanced fault-tolerant CAN transceiver Fault-tolerant CAN transceiver
Pin-to-Pin Compatibility Reference device Documented as pin-to-pin compatible Documented as pin-to-pin compatible Same TJA1055T/3 family Same TJA1055T/3 family Same TJA1055T/3 family

تفاوت‌های کلیدی

  • Enhanced fault-tolerant CAN interface (در مقابلTJA1054)
  • Documented pin-to-pin replacement path (در مقابلTJA1054A)
  • Same-family interface alternatives (در مقابلTJA1055T/3/C-T)

یادداشت‌های طراحی

Route CANH and CANL as a closely coupled differential pair with continuous reference to the board ground plane. Keep the transceiver close to the bus connector or CAN controller, minimize branch stubs, and avoid routing the pair through switching-power or high-current paths. Verify that the PCB land pattern follows the 14-pin SOIC drawing in the NXP datasheet and that pin 1 orientation matches the assembly package.

Do not treat physical pin compatibility as proof that every ordering variant is interchangeable. The TJA1055T/3 family includes ordering codes that identify interface, sourcing, or packing differences. Confirm the supply arrangement, controller logic levels, operating modes, temperature grade, and shipping format for the exact replacement. The TJA1054 and TJA1054A are specifically documented as pin-to-pin compatible, but their complete electrical characteristics still require review.

Apply the NXP reference circuit around the transceiver, including the specified decoupling and bus-interface components. Keep the supply and ground paths short, connect the device ground reference as directed, and account for voltage drop and transient conditions across the module wiring. The TJA1055T/3/CM supports a 5 V to 28 V range, but that rating does not eliminate the need for correct supply filtering and automotive transient protection.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The product listing identifies the device as automotive AEC-Q100. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the product information and remain unknown.

تاریخ تأیید داده‌ها: 2026-11-18 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

tja1055t c datasheet TJA1055T/3/CM datasheet TJA1055T/3/CM pinout TJA1055T/3/CM datasheet pdf TJA1055T/3/CM equivalent TJA1055T/3/CM replacement TJA1055T/3/CM cross reference TJA1055T/3/CM vs TJA1054A TJA1055T/3/CM application circuit TJA1055T/3/CM price TJA1055T/3/CM stock NXP TJA1055T/3/CM

قطعات و اصطلاحات مرتبط

NXP Semiconductors TJA1055T/3/CM TJA1055T TJA1054 TJA1054A TJA1055T/3/1 TJA1055T/3/1J TJA1055T/3/C-T CAN transceiver Controller Area Network CAN protocol controller differential signaling CANH CANL fault-tolerant transceiver low-speed CAN 125 kBd sleep mode standby mode SOIC-14 surface mount automotive electronics AEC-Q100 NXP TJA1055 datasheet
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ