Texas Instruments

TLV2404ID - 16V Quad MicroPower RRIO Op Amp | Texas Instruments

MPN: TLV2404ID ✓ فعال
16 V Vdss 880 nA Id 14-pin SOIC Package
حداقل سفارش: 1 |

TLV2404ID نمای کلی

The Texas Instruments TLV2404ID is a quad, rail-to-rail input and output operational amplifier designed for low-power analog signal conditioning from a single supply up to 16 V. Each amplifier supports a 5.5 kHz gain-bandwidth product and operates with a low 880 nA per-channel supply current. The device is offered in a 14-pin SOIC package for surface-mount assembly. These characteristics make it suitable for portable instrumentation, battery-powered monitoring, sensor interfaces, and low-frequency signal-conditioning circuits where four amplifiers are needed in one package.

An operational amplifier is an analog integrated circuit that uses high-gain feedback to amplify the difference between two input voltages. The TLV2404 belongs to the rail-to-rail-input and rail-to-rail-output amplifier category, allowing its input and output stages to operate close to the supply rails. This rail-to-rail behavior is particularly useful in single-supply systems in which signal headroom is limited and internal supply rails are not available for biasing.

The principal features of the TLV2404 include four amplifiers per package, an operating supply range extending to 16 V, 880 nA supply current per channel, a 5.5 kHz gain-bandwidth product, and rail-to-rail input and output operation. The low channel current reduces the contribution of the amplifier itself to total system power. The 5.5 kHz bandwidth is appropriate for low-frequency sensor signals, filtering, buffering, and gain stages rather than high-speed communications or precision waveform capture.

Reverse-battery protection is included to guard the amplifier against excessive current caused by incorrect battery installation. The family also supports single-supply operation, which simplifies designs powered from one battery cell or a low-voltage rail. These features make the TLV2404 useful in portable and industrial systems where supply current, voltage range, input range, and fault tolerance affect practical reliability.

Typical applications include low-power sensor conditioning, battery-operated monitors, portable measurement equipment, current-loop receivers, and four-channel signal buffering. In each case, the amplifier can operate near the supply rails while consuming very little current per channel. Designs requiring substantially higher signal bandwidth, lower offset voltage, lower output distortion, or faster settling should use an amplifier selected for those specifications instead.

The primary layout consideration is to maintain a clean low-noise supply connection and place input and output components close to their associated pins. Because the amplifier is intended for low-frequency, low-power operation, PCB leakage, contamination, input bias currents, and capacitor leakage can become more important than high-frequency placement alone suggests. Verify operation across the complete supply range and temperature range used by the final product.

This page organizes the TLV2404ID electrical characteristics, package information, application guidance, verified drop-in information, and selection considerations into one engineering reference. It also distinguishes documented operating facts from parameters that must be checked against the manufacturer datasheet before a production design is released.

جایگزین‌های drop-in برای TLV2404ID — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای TLV2404ID (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Operating Temperature Range, Package, Product Type, Reverse-Battery Protection.

Texas Instruments
Operating Temperature Range: -40°C to +125°C
Package: 8-SOIC
Product Type: Single operational amplifier
مقایسه با TLV2404ID →

TLV2404IDG4

✅ جایگزین مستقیم
📦 14-SOIC
Same 14-SOIC electrical configuration and 880 nA per-channel supply current; orderable packaging suffix differs by 0% in the compared functional parameters

📋 جایگزین مرجع (خارج از کاتالوگ)

TLV2404ID حداکثر مقادیر مجاز و مشخصات الکتریکی

Number of Amplifiers 4 channels
Product Type General-purpose operational amplifier
Maximum Supply Voltage 16 V
Supply Current per Channel 880 nA
Gain-Bandwidth Product 5.5 kHz
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Reverse-Battery Protection Supported
محدوده دمای کاری -40 °C to +125 °C
بسته‌بندی 14-pin SOIC
نوع نصب Surface mount
Amplifier Type Single-supply
Unity-Gain Bandwidth 5.5 kHz

راهنمای پیکربندی پین TLV2404ID 14-pin soic

پیکربندی پین برای TLV2404ID (پکیج 14-pin soic). این قطعه آنالوگ دارای پین‌های ورودی، خروجی و تغذیه است. برای پیکربندی‌های پین offset null، جبران‌سازی و فعال‌سازی به دیتاشیت سازنده مراجعه کنید. ایده‌آل برای مدارهای شرطی‌سازی سیگنال و تقویت‌کننده.

نمودار پین‌آوت پکیج 14-pin soic برای TLV2404ID

داده پین‌آوت تفصیلی موجود نیست برای TLV2404ID.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

TLV2404ID مناسب است برای 6 کاربردs: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Process Monitoring, Low-Power Current Loop Receiver, Portable Data Acquisition, Low-Leakage Voltage Buffer.

🧩

Battery-Powered Sensor Conditioning

The TLV2404ID fits low-power sensor-conditioning paths where four channels can share a single package and operate from a compact battery-derived rail. Its 880 nA per-channel supply current minimizes amplifier contribution to standby power, while rail-to-rail input and output behavior improves usable signal range in single-supply systems. The 5.5 kHz gain-bandwidth product is appropriate for slowly varying sensor outputs, filtered pressure or temperature channels, and buffered measurements. Place the active device close to the sensor interface, use high-impedance biasing, and verify input bias current and leakage against the source impedance. The main trade-off is bandwidth: signals with meaningful content above the amplifier’s usable closed-loop range require a higher-speed amplifier.

💊

Portable Medical Monitoring

The TLV2404ID can support low-bandwidth amplification stages in portable medical monitoring equipment when its input offset, bias-current, and noise characteristics meet the required measurement limits. The 880 nA per-channel supply current is useful for extending battery life, and the 14-pin SOIC allows four amplifiers to be consolidated into one package. Rail-to-rail operation helps when the available supply headroom is limited. Typical uses include buffered sensor inputs, threshold amplification, and low-frequency gain stages around an ADC. Compliance with any medical-system requirement remains a system-level determination; check leakage, input protection, electromagnetic immunity, and the complete signal chain before deployment.

🏭

Industrial Process Monitoring

The TLV2404ID is applicable to low-speed industrial process monitoring when each channel carries a filtered pressure, level, or temperature signal. Its wide 16 V maximum supply supports higher-voltage industrial rails, and rail-to-rail input and output operation improves headroom around a single low-voltage supply. Four channels in one 14-pin SOIC reduce board-area requirements compared with separate single amplifiers. The amplifier’s 5.5 kHz bandwidth is adequate for slow sensor signals after suitable filtering but not for wideband transients. Validate isolation barriers, input protection, grounding, input bias-current error, and the final control-loop bandwidth rather than assuming the amplifier alone satisfies industrial robustness requirements.

📡

Low-Power Current Loop Receiver

The TLV2404ID can serve as the receiver amplifier in a low-speed current-measurement loop when the loop bandwidth and system capacitance permit operation at 5.5 kHz gain-bandwidth product. Its low 880 nA per-channel supply current reduces the receiver’s contribution to total instrumentation power, while rail-to-rail input and output capability supports single-supply implementation. Four channels can process multiple transducer loops or provide buffering and filtering stages on the same board. The design should account for input common-mode range, offset voltage, bias current, noise, and stability with the transmitter and cable capacitance. For faster loops or higher accuracy, use an amplifier with greater bandwidth and lower offset rather than forcing the TLV2404ID beyond its documented operating region.

🖥️

Portable Data Acquisition

The TLV2404ID is suited to buffering and conditioning several slowly changing inputs in a portable data-acquisition system. Four amplifiers in one 14-pin SOIC package reduce component count, while 880 nA per channel leaves more of the battery budget for the processor, display, and communications. Rail-to-rail inputs and outputs help preserve dynamic range when the converter or sensor operates close to the supply rails. At 5.5 kHz gain-bandwidth product, the amplifiers suit temperature, pressure, potentiometer, and other low-frequency channels rather than high-rate waveform acquisition. Confirm that source impedance does not create unacceptable bias-current error and that anti-alias filtering is placed ahead of any higher-speed converter.

🔧

Low-Leakage Voltage Buffer

The TLV2404ID can buffer slowly varying high-impedance voltage sources when the required input bias current and leakage are compatible with the source. Its rail-to-rail input and output characteristics preserve signal span in a single-supply circuit, and the 880 nA per-channel current is attractive for always-on equipment. Four channels make it practical to buffer multiple sensor lines without using four separate packages. Care is required with contaminated PCBs, long traces, and moisture because those effects can dominate the amplifier’s own input error. Add guarding, keep input traces short, and provide suitable filtering. If the source requires very low input bias current or faster response, choose a specialized low-leakage or higher-bandwidth amplifier instead.

What is the TLV2404ID?
The TLV2404ID is a four-channel, general-purpose operational amplifier from Texas Instruments in a 14-pin SOIC package. According to the manufacturer product page and datasheet, the device operates from a single supply up to 16 V, provides rail-to-rail input and output operation, consumes 880 nA per channel, and has a gain-bandwidth product of 5.5 kHz. It is intended for low-power, low-frequency analog signal-conditioning systems.
What is the operating voltage of the TLV2404ID?
The TLV2404ID supports a maximum supply voltage of 16 V and is designed for single-supply operation. According to the Texas Instruments product page, the amplifier also supports rail-to-rail input and output operation, allowing signals to approach the positive and negative supply limits under suitable load and output conditions. Confirm the minimum operating supply, input range, and output limits in the manufacturer datasheet for the selected operating point.
What are the key specifications of TLV2404ID that engineers should know?
The key TLV2404ID specifications are four amplifier channels, a 16 V maximum supply, 880 nA supply current per channel, a 5.5 kHz gain-bandwidth product, and rail-to-rail input and output operation. According to the Texas Instruments product page, the family also includes reverse-battery protection. These parameters position the device for low-power, low-frequency instrumentation rather than high-speed or high-precision signal chains.
Where can I download the TLV2404ID datasheet PDF?
The TLV2404ID datasheet PDF is available from the Texas Instruments product-support page for the TLV2404 family. Use the manufacturer document at https://www.ti.com/lit/gpn/TLV2404 for the authoritative pin descriptions, electrical characteristics, typical performance curves, and ordering information. The 14-pin SOIC pin assignment and full operating limits should be taken from that document rather than inferred from the family description.
Where is the TLV2404ID pinout located?
The TLV2404ID pinout is shown in the pin-configuration section of the Texas Instruments TLV2404 family datasheet. The exact ordering code uses a 14-pin SOIC package, but the pin numbers and signal names must be taken from the datasheet because the exposed thermal arrangement and package drawing are part of the ordering documentation. Use that pin table when assigning PCB tracks and checking no-connect positions.
Is the TLV2404ID suitable for battery-powered sensor interfaces?
The TLV2404ID is well suited to many battery-powered sensor interfaces because it consumes only 880 nA per channel and supports rail-to-rail input and output operation. According to the manufacturer product page, its maximum supply voltage is 16 V, allowing operation from common low-voltage rails. Sensor excitation, input bias current, leakage, settling time, and common-mode range should still be checked for the specific transducer and signal bandwidth.
What can replace the TLV2404ID?
The closest identified replacement is TLV2404IDG4 because it represents the same TLV2404ID device configuration, but its packaging code differs and it should not be treated as an interchangeable substitute without checking reel orientation and labeling. No additional pin-compatible replacement can be established from the available cross-reference information. Use the Texas Instruments cross-reference search for a broader manufacturer-qualified replacement and verify the 14-pin SOIC pinout, supply range, bandwidth, and temperature grade.
Is TLV2404ID the same as TLV2404IDG4?
TLV2404ID and TLV2404IDG4 identify the same TLV2404ID device configuration with different orderable packaging or carrier codes. The available comparison information identifies TLV2404IDG4 as a 14-SOIC micro-power, rail-to-rail I/O amplifier with an 880 nA per-channel supply current. Because the difference is primarily orderable packaging, check the label, reel orientation, moisture requirements, and BOM suffix before treating them as identical.
When should I choose TLV2404ID over a higher-bandwidth amplifier?
Choose the TLV2404ID when the signal bandwidth is low and battery or standby power is more important than fast settling or low distortion. According to the manufacturer product page, its gain-bandwidth product is 5.5 kHz and its supply current is 880 nA per channel. Select a faster amplifier when the signal contains substantial high-frequency content, requires rapid settling, or demands lower output distortion.
Is the TLV2404ID suitable for industrial instrumentation?
The TLV2404ID can be suitable for low-frequency industrial instrumentation when its documented temperature range and electrical limits satisfy the system requirements. The ordering information identifies an operating range of -40 °C to +125 °C and a 14-pin SOIC package. Verify input bias current, offset, noise, common-mode behavior, and stability with the selected feedback network because the 5.5 kHz bandwidth is intentionally low.
How much power does the TLV2404ID consume?
The TLV2404ID consumes 880 nA per amplifier channel under the manufacturer’s specified supply-current conditions. Because the package contains four channels, the corresponding supply-current contribution is 3.52 µA when all four channels are active and the same conditions apply. Actual board consumption also includes bias-reference, output-load, leakage, and external-circuit currents, so measure the complete circuit for an energy budget.
Where to buy TLV2404ID online?
Use the Request a Quote form on this page to request TLV2404ID availability, lot traceability, and order confirmation. The form is the appropriate channel for current commercial terms and avoids publishing a price that may not match the requested quantity or packaging. Provide the exact TLV2404ID suffix, target quantity, and delivery requirements so the request can be routed correctly.
What is the price of the TLV2404ID?
The current commercial price for TLV2404ID is returned through the Request a Quote form on this page because pricing can vary with quantity, carrier, and fulfillment terms. Use that form to request a current quotation for the exact TLV2404ID orderable part number. The form should also capture any required production quantity, traceability, and delivery schedule.
What is the lead time for TLV2404ID?
The current lead time for TLV2404ID should be confirmed through the Request a Quote form on this page. Include the required quantity, approved manufacturer part number, target date, and any lot-control requirements in the request. The manufacturer lists the TLV2404ID as active, but manufacturing availability and order scheduling can change and are not represented by a static listing.
Does the TLV2404ID include reverse-battery protection?
Yes, the TLV2404 family includes reverse-battery protection intended to guard against excessive current caused by improper battery installation. According to the manufacturer family description, this protection is one of the distinguishing features of the low-power TLV240x devices. It does not remove the need for correct installation or normal overvoltage and current protection in the finished product.
What is the TLV2404ID vs TLV2404IDG4 difference?
The available product information indicates that TLV2404ID and TLV2404IDG4 refer to the same 14-SOIC, quad, 880 nA-per-channel operational-amplifier configuration, with the suffix distinguishing an orderable packaging configuration. There is no published functional difference in the available comparison material. Engineering teams should still verify carrier orientation, labeling, moisture-packaging requirements, and traceability before substituting one order code for another.

داده‌های مرجع مهندسی برای TLV2404ID — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the TLV2404ID for low-frequency, low-power analog circuits that require four rail-to-rail amplifiers in a standard 14-pin SOIC package. Its 880 nA per-channel supply current is especially attractive for battery-operated monitors, portable measurement systems, and always-on sensor interfaces, while the 5.5 kHz gain-bandwidth product is appropriate for filtered temperature, pressure, level, potentiometer, and similar low-frequency signals. The TLV2404IDG4 is the closest identified orderable counterpart, but its suffix represents a packaging configuration, so confirm labeling, reel orientation, and moisture-packaging requirements. Select a different amplifier when the design needs substantially more bandwidth, faster settling, lower offset voltage, lower distortion, or lower input bias current. For automotive or other specialized applications, verify qualification requirements separately; the available technical summary establishes the electrical family characteristics but does not establish every certification attribute.

مقایسه با جایگزین‌ها

پارامتر این محصول TLV2404IDG4
Package 14-SOIC 14-SOIC
Brand Texas Instruments Texas Instruments
Number of Amplifiers 4 channels 4 channels
Maximum Supply Voltage 16 V 16 V
Supply Current per Channel 880 nA 880 nA
Gain-Bandwidth Product 5.5 kHz 5.5 kHz
Input Common-Mode Range Rail-to-rail Rail-to-rail
Output Swing Rail-to-rail Rail-to-rail
Reverse-Battery Protection Supported Supported
Operating Temperature Range -40 °C to +125 °C -40 °C to +125 °C

تفاوت‌های کلیدی

  • Four amplifiers in one 14-SOIC package (در مقابلTLV2404IDG4)
  • Very low per-channel supply current (در مقابلTLV2404IDG4)
  • Rail-to-rail input and output operation (در مقابلTLV2404IDG4)
  • Reverse-battery protection (در مقابلTLV2404IDG4)

یادداشت‌های طراحی

Budget the complete circuit rather than the amplifier symbol alone. The four active channels contribute 880 nA each, or 3.52 µA total, under the manufacturer’s stated supply-current conditions. Add sensor bias currents, reference consumption, pull networks, and load current to determine the real battery drain. Because the device supports single-supply operation, also check whether a separate rail or level shift is required for downstream signaling.

Keep the 14-pin SOIC power and ground connections close to the device and provide a low-impedance return path for each amplifier. Route sensitive input traces away from switching nodes and high-current return paths. At the low signal bandwidth supported by the TLV2404, PCB contamination and leakage can dominate the error budget, so use clean boards, guard rings where appropriate, and conformal protection in humid or contaminated environments.

Do not treat the 5.5 kHz gain-bandwidth product as adequate for arbitrary signal waveforms. Closed-loop gain reduces available bandwidth, and large output transitions can be limited by slew rate and output-current capability. Check the required signal amplitude, frequency, settling time, load capacitance, and noise bandwidth against the manufacturer’s electrical characteristics before choosing the amplifier for precision or dynamic measurements.

For high-impedance sources, minimize input-trace area, keep the input path away from contaminated board regions, and avoid long parallel runs above exposed ground planes. Input bias-current error depends on source impedance and device leakage. If the signal source can source or sink very little current, compare the TLV2404ID input-bias specification with the source requirements or use a low-leakage amplifier instead.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The available manufacturer summary confirms the TLV2404 family electrical characteristics and active product listing but does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.

تاریخ تأیید داده‌ها: 2026-11-19 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

TLV2404ID datasheet TLV2404ID pinout TLV2404ID datasheet pdf TLV2404ID equivalent TLV2404ID replacement TLV2404ID cross reference TLV2404ID vs TLV2404IDG4 Texas Instruments TLV2404ID TLV2404ID 14-SOIC pinout TLV2404ID application circuit TLV2404ID price TLV2404ID stock TLV2404ID 880 nA amplifier TLV2404ID 5.5 kHz op amp

قطعات و اصطلاحات مرتبط

Texas Instruments TLV2404ID TLV2404IDG4 TLV2404 operational amplifier quad amplifier rail-to-rail input rail-to-rail output single-supply amplifier micropower amplifier signal-conditioning IC analog integrated circuit semiconductor 14-pin SOIC SOIC package family surface-mount package SMD 880 nA per channel 5.5 kHz gain-bandwidth product 16 V maximum supply voltage reverse-battery protection -40 °C to +125 °C operating temperature range battery-powered instrumentation sensor interface
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ