TLV2404ID - 16V Quad MicroPower RRIO Op Amp | Texas Instruments
MPN: TLV2404ID ✓ فعالTLV2404ID جائزہ
An operational amplifier is an analog integrated circuit that uses high-gain feedback to amplify the difference between two input voltages. The TLV2404 belongs to the rail-to-rail-input and rail-to-rail-output amplifier category, allowing its input and output stages to operate close to the supply rails. This rail-to-rail behavior is particularly useful in single-supply systems in which signal headroom is limited and internal supply rails are not available for biasing.
The principal features of the TLV2404 include four amplifiers per package, an operating supply range extending to 16 V, 880 nA supply current per channel, a 5.5 kHz gain-bandwidth product, and rail-to-rail input and output operation. The low channel current reduces the contribution of the amplifier itself to total system power. The 5.5 kHz bandwidth is appropriate for low-frequency sensor signals, filtering, buffering, and gain stages rather than high-speed communications or precision waveform capture.
Reverse-battery protection is included to guard the amplifier against excessive current caused by incorrect battery installation. The family also supports single-supply operation, which simplifies designs powered from one battery cell or a low-voltage rail. These features make the TLV2404 useful in portable and industrial systems where supply current, voltage range, input range, and fault tolerance affect practical reliability.
Typical applications include low-power sensor conditioning, battery-operated monitors, portable measurement equipment, current-loop receivers, and four-channel signal buffering. In each case, the amplifier can operate near the supply rails while consuming very little current per channel. Designs requiring substantially higher signal bandwidth, lower offset voltage, lower output distortion, or faster settling should use an amplifier selected for those specifications instead.
The primary layout consideration is to maintain a clean low-noise supply connection and place input and output components close to their associated pins. Because the amplifier is intended for low-frequency, low-power operation, PCB leakage, contamination, input bias currents, and capacitor leakage can become more important than high-frequency placement alone suggests. Verify operation across the complete supply range and temperature range used by the final product.
This page organizes the TLV2404ID electrical characteristics, package information, application guidance, verified drop-in information, and selection considerations into one engineering reference. It also distinguishes documented operating facts from parameters that must be checked against the manufacturer datasheet before a production design is released.
کے لیے ڈراپ اِن متبادل TLV2404ID — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں TLV2404ID (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Operating Temperature Range, Package, Product Type, Reverse-Battery Protection.
TLV2404IDG4
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TLV2404ID زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Number of Amplifiers | 4 channels |
| Product Type | General-purpose operational amplifier |
| Maximum Supply Voltage | 16 V |
| Supply Current per Channel | 880 nA |
| Gain-Bandwidth Product | 5.5 kHz |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Reverse-Battery Protection | Supported |
| آپریٹنگ درجہ حرارت رینج | -40 °C to +125 °C |
| پیکیج | 14-pin SOIC |
| ماؤنٹنگ ٹائپ | Surface mount |
| Amplifier Type | Single-supply |
| Unity-Gain Bandwidth | 5.5 kHz |
TLV2404ID 14-pin soic پن کنفیگریشن گائیڈ
TLV2404ID (14-pin soic پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں TLV2404ID.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
TLV2404ID کے لیے موزوں ہے 6 ایپلیکیشنs: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Process Monitoring, Low-Power Current Loop Receiver, Portable Data Acquisition, Low-Leakage Voltage Buffer.
Battery-Powered Sensor Conditioning
The TLV2404ID fits low-power sensor-conditioning paths where four channels can share a single package and operate from a compact battery-derived rail. Its 880 nA per-channel supply current minimizes amplifier contribution to standby power, while rail-to-rail input and output behavior improves usable signal range in single-supply systems. The 5.5 kHz gain-bandwidth product is appropriate for slowly varying sensor outputs, filtered pressure or temperature channels, and buffered measurements. Place the active device close to the sensor interface, use high-impedance biasing, and verify input bias current and leakage against the source impedance. The main trade-off is bandwidth: signals with meaningful content above the amplifier’s usable closed-loop range require a higher-speed amplifier.
تجویز کردہ
Portable Medical Monitoring
The TLV2404ID can support low-bandwidth amplification stages in portable medical monitoring equipment when its input offset, bias-current, and noise characteristics meet the required measurement limits. The 880 nA per-channel supply current is useful for extending battery life, and the 14-pin SOIC allows four amplifiers to be consolidated into one package. Rail-to-rail operation helps when the available supply headroom is limited. Typical uses include buffered sensor inputs, threshold amplification, and low-frequency gain stages around an ADC. Compliance with any medical-system requirement remains a system-level determination; check leakage, input protection, electromagnetic immunity, and the complete signal chain before deployment.
تجویز کردہ
Industrial Process Monitoring
The TLV2404ID is applicable to low-speed industrial process monitoring when each channel carries a filtered pressure, level, or temperature signal. Its wide 16 V maximum supply supports higher-voltage industrial rails, and rail-to-rail input and output operation improves headroom around a single low-voltage supply. Four channels in one 14-pin SOIC reduce board-area requirements compared with separate single amplifiers. The amplifier’s 5.5 kHz bandwidth is adequate for slow sensor signals after suitable filtering but not for wideband transients. Validate isolation barriers, input protection, grounding, input bias-current error, and the final control-loop bandwidth rather than assuming the amplifier alone satisfies industrial robustness requirements.
تجویز کردہ
Low-Power Current Loop Receiver
The TLV2404ID can serve as the receiver amplifier in a low-speed current-measurement loop when the loop bandwidth and system capacitance permit operation at 5.5 kHz gain-bandwidth product. Its low 880 nA per-channel supply current reduces the receiver’s contribution to total instrumentation power, while rail-to-rail input and output capability supports single-supply implementation. Four channels can process multiple transducer loops or provide buffering and filtering stages on the same board. The design should account for input common-mode range, offset voltage, bias current, noise, and stability with the transmitter and cable capacitance. For faster loops or higher accuracy, use an amplifier with greater bandwidth and lower offset rather than forcing the TLV2404ID beyond its documented operating region.
تجویز کردہ
Portable Data Acquisition
The TLV2404ID is suited to buffering and conditioning several slowly changing inputs in a portable data-acquisition system. Four amplifiers in one 14-pin SOIC package reduce component count, while 880 nA per channel leaves more of the battery budget for the processor, display, and communications. Rail-to-rail inputs and outputs help preserve dynamic range when the converter or sensor operates close to the supply rails. At 5.5 kHz gain-bandwidth product, the amplifiers suit temperature, pressure, potentiometer, and other low-frequency channels rather than high-rate waveform acquisition. Confirm that source impedance does not create unacceptable bias-current error and that anti-alias filtering is placed ahead of any higher-speed converter.
تجویز کردہ
Low-Leakage Voltage Buffer
The TLV2404ID can buffer slowly varying high-impedance voltage sources when the required input bias current and leakage are compatible with the source. Its rail-to-rail input and output characteristics preserve signal span in a single-supply circuit, and the 880 nA per-channel current is attractive for always-on equipment. Four channels make it practical to buffer multiple sensor lines without using four separate packages. Care is required with contaminated PCBs, long traces, and moisture because those effects can dominate the amplifier’s own input error. Add guarding, keep input traces short, and provide suitable filtering. If the source requires very low input bias current or faster response, choose a specialized low-leakage or higher-bandwidth amplifier instead.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا TLV2404ID — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | TLV2404IDG4 |
|---|---|---|
| Package | 14-SOIC | 14-SOIC |
| Brand | Texas Instruments | Texas Instruments |
| Number of Amplifiers | 4 channels | 4 channels |
| Maximum Supply Voltage | 16 V | 16 V |
| Supply Current per Channel | 880 nA | 880 nA |
| Gain-Bandwidth Product | 5.5 kHz | 5.5 kHz |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Reverse-Battery Protection | Supported | Supported |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C |
اہم امتیازی خصوصیات
- Four amplifiers in one 14-SOIC package (بمقابلہTLV2404IDG4)
- Very low per-channel supply current (بمقابلہTLV2404IDG4)
- Rail-to-rail input and output operation (بمقابلہTLV2404IDG4)
- Reverse-battery protection (بمقابلہTLV2404IDG4)
ڈیزائن نوٹس
Budget the complete circuit rather than the amplifier symbol alone. The four active channels contribute 880 nA each, or 3.52 µA total, under the manufacturer’s stated supply-current conditions. Add sensor bias currents, reference consumption, pull networks, and load current to determine the real battery drain. Because the device supports single-supply operation, also check whether a separate rail or level shift is required for downstream signaling.
Keep the 14-pin SOIC power and ground connections close to the device and provide a low-impedance return path for each amplifier. Route sensitive input traces away from switching nodes and high-current return paths. At the low signal bandwidth supported by the TLV2404, PCB contamination and leakage can dominate the error budget, so use clean boards, guard rings where appropriate, and conformal protection in humid or contaminated environments.
Do not treat the 5.5 kHz gain-bandwidth product as adequate for arbitrary signal waveforms. Closed-loop gain reduces available bandwidth, and large output transitions can be limited by slew rate and output-current capability. Check the required signal amplitude, frequency, settling time, load capacitance, and noise bandwidth against the manufacturer’s electrical characteristics before choosing the amplifier for precision or dynamic measurements.
For high-impedance sources, minimize input-trace area, keep the input path away from contaminated board regions, and avoid long parallel runs above exposed ground planes. Input bias-current error depends on source impedance and device leakage. If the signal source can source or sink very little current, compare the TLV2404ID input-bias specification with the source requirements or use a low-leakage amplifier instead.
تعمیل کی معلومات
The available manufacturer summary confirms the TLV2404 family electrical characteristics and active product listing but does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.