XC4VLX25-12FFG676C - Virtex-4 LX FPGA, 24192 LUTs, 448 I/O | AMD
MPN: XC4VLX25-12FFG676C ✗ پایان تولیدXC4VLX25-12FFG676C نمای کلی
A field programmable gate array is a reconfigurable digital integrated circuit whose logic, interconnect and memory blocks are programmed after manufacture. Within the semiconductor hierarchy an FPGA sits above a fixed-function ASIC as a programmable alternative, and within the FPGA family the Virtex-4 LX device targets general-purpose high-performance logic, DSP and embedded processing rather than extreme density or lowest cost.
Key features of this device include 24,192 logic cells and 2,688 CLBs for wide datapath and control-logic implementation, 1,327,104 bits of block RAM for buffered packet or video line storage, 448 user I/O for high-pin-count external interfaces, and a maximum clock frequency of approximately 1205 MHz in the -12 speed grade. The -12 designation denotes the middle speed grade of the Virtex-4 LX family, balancing performance against static power in industrial and commercial equipment.
Architecturally, the device uses 8-input lookup table logic elements with dedicated carry chains, distributed RAM, and dedicated DSP48 arithmetic slices, all linked by programmable routing over column-based interconnect. Multiple on-chip regulators supply the internal core, block RAM and I/O banks, so a single 1.2 V rail family covers core, auxiliary and I/O supplies. Because a 676-ball FCBGA has thousands of fine-pitch balls, this part is intended for multilayer boards with via-in-pad and careful escape-routing techniques.
Typical applications include telecom line-card and cross-connect equipment, network interface and packet-processing line cards, industrial control and data-acquisition systems, video and image processing pipelines, storage and SAS controllers, and test-and-measurement instrumentation with high-speed serial links.
When laying out a board around this FPGA, follow the Virtex-4 package and pinout specification for ball assignment, keep unused VCCO and VCC balls connected as shown in the guidance, and provide clean decoupling on every supply rail. Because the -12 grade is specified to 85 °C junction temperature, derate output-current and speed budgets in hot enclosures or specify an industrial-grade counterpart instead.
جایگزینهای drop-in برای XC4VLX25-12FFG676C — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای XC4VLX25-12FFG676C (همان فرمفاکتور و فوتپرینت) — متفاوت در Package, Core Supply Voltage, Mounting Type, Device Type, Logic Cells.
XC4VLX25-12FF676C
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
XC4VLX25-12FFG676I
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
XC4VLX25-11FFG676I
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←XC4VLX25-10FFG676C
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←XC4VLX25-11FFG676C
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←XC4VLX25-10FFG676I
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←XC4VLX25-12FFG676C حداکثر مقادیر مجاز و مشخصات الکتریکی
| Device Type | Virtex-4 LX Field Programmable Gate Array (FPGA) |
| Logic Cells | 24,192 |
| Configurable Logic Blocks (CLBs) | 2,688 |
| Total RAM Bits | 1,327,104 bits |
| User I/O Pins | 448 |
| بستهبندی | 676-ball plastic epoxy BGA (FCBGA / FFG) |
| Process Technology | 90 nm CMOS |
| Core Supply Voltage | 1.2 V nominal (1.14 V to 1.26 V) |
| Speed Grade | -12 |
| حداکثر فرکانس کلاک | 1205 MHz |
| Junction Temperature Range | 0 °C to 85 °C |
| Temperature Grade | Commercial (C) |
| نوع نصب | Surface mount, BGA |
| Number of Balls | 676 |
| وضعیت چرخه عمر | End-of-life (Virtex-4 generation) |
راهنمای پیکربندی پین XC4VLX25-12FFG676C 676-ball plastic epoxy bga (fcbga / ffg)
پیکربندی پین برای XC4VLX25-12FFG676C (پکیج 676-ball plastic epoxy bga (fcbga / ffg)). این IC دیجیتال شامل GPIO، رابطهای ارتباطی (UART، SPI، I2C) و پینهای تغذیه است. برای عملکردهای جایگزین پین و گزینههای پیکربندی به دیتاشیت سازنده مراجعه کنید. ضروری برای طراحی سیستمهای نهفته و چیدمان PCB.
داده پینآوت تفصیلی موجود نیست برای XC4VLX25-12FFG676C.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
XC4VLX25-12FFG676C مناسب است برای 6 کاربردs: Telecom Line-Card and Cross-Connect Equipment, Industrial Control and Data-Acquisition, Video and Image Processing Pipelines, Network Interface and Packet-Processing Cards, Storage and SAS Controller Equipment, Test and Measurement Instrumentation.
Telecom Line-Card and Cross-Connect Equipment
The XC4VLX25-12FFG676C fits line-card designs that need wide parallel bus widths alongside high-speed serial links. With 448 user I/O available in the 676-ball FFG package, a card can absorb the parallel sideband and control traffic of a switching fabric while the dedicated high-speed transceivers carry payload data, and the 2,688 CLBs provide the cross-connect switching fabric logic. Its 24,192 logic cells and 1,327,104 bits of block RAM also allow sizeable packet buffers to be built on-chip instead of in external SRAM. The -12 grade and 0 °C to 85 °C junction range suit indoor telecom cabinets, where airflow is often restricted, and the 1.2 V core supply simplifies rail planning on a dense multilayer card.
پیشنهادی
Industrial Control and Data-Acquisition
Machine vision and factory data-acquisition systems benefit from the XC4VLX25-12FFG676C because 448 user I/O allows many sensor, encoder and actuator lines to be served from one device, while the DSP48 multipliers and 1,327,104 bits of block RAM handle real-time filtering and frame buffering. The 0 °C to 85 °C junction range matches typical factory ambient conditions, and the -12 speed grade supports the sample rates common in machine vision pipelines. A practical design point is the 1.2 V core rail: decoupling must be placed close to the supply balls, and each VCCO bank must be tied to a rail that matches the external logic level, since mixed-voltage I/O banks are the main source of field failures in this class of equipment.
پیشنهادی
Video and Image Processing Pipelines
Video infrastructure and image-processing boards use the XC4VLX25-12FFG676C for pixel-rate datapaths that must be reconfigured per product variant. The 24,192 logic cells implement colour-space conversion, de-interlacing and scaler pipelines, the dedicated DSP48 slices multiply filter coefficients, and the 1,327,104 bits of block RAM absorb line buffers so that multi-frame pipelines run without external memory. The 448 user I/O is also enough to bring in parallel sensor or video-capture interfaces alongside a serial link back to a host processor. Because the device is end-of-life, video system builders should confirm residual inventory early, since board respins to newer families are rarely drop-in and the pinout and bitstream both change.
پیشنهادی
Network Interface and Packet-Processing Cards
Network adapters and packet-processing line cards need deterministic throughput, flexible parsing and plenty of buffer memory, which is exactly the profile of the XC4VLX25-12FFG676C. Its 2,688 CLBs can implement header parsing, classification and queueing logic, while the 1,327,104 bits of block RAM host descriptor and payload buffers that keep the design free of external SRAM in moderate-throughput products. The 448 user I/O in the FFG package supports parallel fabric-side interfaces, and the 90 nm Virtex-4 silicon is proven in networking appliances. The engineering trade-off is that the -12 speed grade caps the fabric clock near 1205 MHz, so designs needing multi-gigabit per-lane rates at the edge should place serial transceivers close to the fabric and verify timing closure early in the schedule.
پیشنهادی
Storage and SAS Controller Equipment
RAID and SAS controller designs use the XC4VLX25-12FFG676C because they combine protocol logic, ECC handling and buffering in one programmable device. The 24,192 logic cells are adequate for layered SAS or SATA state machines and XOR/ECC engines, the DSP48 slices assist with run-time metadata arithmetic, and the 1,327,104 bits of block RAM support command queues and DMA staging. A wide I/O count of 448 accommodates multiple connector channels and flash-side interfaces without an external CPLD, simplifying the board. Designers should note that the -12 grade and 85 °C junction limit need thermal headroom in dense server-adjacent enclosures, and end-of-life status means long-term supply planning should start now rather than at the point of shortage.
پیشنهادی
Test and Measurement Instrumentation
Instrumentation platforms such as protocol analysers, logic analysers and ATE controllers value the XC4VLX25-12FFG676C for its combination of pattern-generation logic and instrument-grade timing. The 448 user I/O can drive and sample many parallel channels at once, the block RAM holds long capture windows and reference vectors, and the 24,192 logic cells implement multiple concurrent test channels. The 0 °C to 85 °C junction range suits indoor bench and rack equipment. For lab use, the 1.2 V core rail must be filtered aggressively to keep noise out of the measurement floor, and the 676-ball BGA demands careful via-in-pad and de-coupling layout so that switching activity from the fabric does not perturb analogue reference paths on the same board.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای XC4VLX25-12FFG676C — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | XC4VLX25-12FF676C | XC4VLX25-12FFG676I | XC4VLX25-11FFG676I | XC4VLX25-10FFG676C | XC4VLX25-11FFG676C |
|---|---|---|---|---|---|---|
| Package | 676-ball FCBGA (FFG) | 676-ball FCBGA (FFG) - same | 676-ball FCBGA (FFG) - same | 676-ball FCBGA (FFG) - same | 676-ball FCBGA (FFG) - same | 676-ball FCBGA (FFG) - same |
| Brand | AMD (formerly Xilinx) | AMD (formerly Xilinx) | AMD (formerly Xilinx) | AMD (formerly Xilinx) | AMD (formerly Xilinx) | AMD (formerly Xilinx) |
| Logic Cells | 24,192 | 24,192 | 24,192 | 24,192 | 24,192 | 24,192 |
| Block RAM Bits | 1,327,104 bits | 1,327,104 bits | 1,327,104 bits | 1,327,104 bits | 1,327,104 bits | 1,327,104 bits |
| User I/O | 448 | 448 | 448 | 448 | 448 | 448 |
| Speed Grade | -12 (approx. 1205 MHz max clock) | -12 (approx. 1205 MHz max clock) | -12 (approx. 1205 MHz max clock) | -11 (approx. 8% slower than -12) | -10 (approx. 10% faster than -12) | -11 (approx. 8% slower than -12) |
| Temperature Grade | G marking, 0 °C to 85 °C junction | C marking, commercial temperature | I marking, extended industrial temperature | I marking, extended industrial temperature | G marking, 0 °C to 85 °C junction | G marking, 0 °C to 85 °C junction |
| Core Supply Voltage | 1.2 V nominal (1.14 V to 1.26 V) | 1.2 V nominal (1.14 V to 1.26 V) | 1.2 V nominal (1.14 V to 1.26 V) | 1.2 V nominal (1.14 V to 1.26 V) | 1.2 V nominal (1.14 V to 1.26 V) | 1.2 V nominal (1.14 V to 1.26 V) |
| Lifecycle Status | End-of-life | End-of-life | End-of-life | End-of-life | End-of-life | End-of-life |
| Process Technology | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS |
تفاوتهای کلیدی
- High user I/O count in the same 676-ball package family (در مقابلXC4VLX25-12FF668I)
- Exact die and footprint match within the XC4VLX25 FFG family (در مقابلXC4VLX25-12FF676C)
- Speed grade headroom above the -12 baseline (در مقابلXC4VLX25-11FFG676I)
- Industrial-junction rating matched to the G marking (در مقابلXC4VLX25-12FF676C)
یادداشتهای طراحی
The 676-ball FFG FCBGA demands escape routing on a dense multilayer board. Follow the Virtex-4 package and pinout specification for ball assignment and recommended layout so that power, ground and high-speed differential pairs reach the device through short, matched paths. Use via-in-pad or a dog-bone escape strategy for the balls, keep the ground plane continuous directly under the package, and route each VCCO bank from a dedicated low-impedance layer. Cross-check the ball map against the exact FFG package and speed suffix before fabrication, because the -668 and -363 package options use completely different ball assignments.
Estimated: with a 1.2 V core rail and a 0.15 A total device current at moderate utilization, the core dissipation is roughly 0.18 W, so the dominant thermal issue on this device is total board power, not the FPGA alone. Place bulk and high-frequency decoupling on every supply rail close to the balls, keep the VCC and VCCO planes separate to avoid injecting rail noise into the I/O receivers, and note that internal regulators mean the 1.2 V input rail must still be clean: excess supply ripple appears directly as added jitter and noise on the fabric clocks.
The most common field errors on Virtex-4 LX boards are wrong supply connections and wrong temperature-grade interpretation. Confirm that every VCC ball is tied to the 1.2 V rail, that each VCCO ball matches the logic level of the bank it serves, and that unused I/O is left uncommitted only if the design intends a pull behaviour. On the qualification side, the -12 grade is specified to a 0 °C to 85 °C junction temperature, so the case temperature plus the calculated rise must stay below 85 °C; otherwise specify the -676I industrial variant. Also remember that a faster -10 or -11 grade device is not automatically a valid substitution if the design was closed against -12 timing.
Because the -12 grade supports clock frequencies up to approximately 1205 MHz, treat board-level timing as a real constraint rather than a theoretical one. Keep clock routing on dedicated layers with short stubs, provide matched 50-ohm single-ended or 100-ohm differential environments for the high-speed serial transceiver pins, and avoid routing user I/O signals beneath the package wherever possible. Reserve clean, low-noise planes for analogue reference sections of the same board, since the FPGA fabric switching activity can couple into adjacent planes if the stack-up lacks a solid ground separator.
اطلاعات انطباق
No RoHS, REACH, lead-free or AEC-Q100 statement appears in the manufacturer listings for this part. The device is an industrial/communications-grade FPGA rather than an automotive-qualified product, so AEC-Q100 does not apply. Compliance documentation for the exact XC4VLX25-12FFG676C suffix should be requested from the supplier.