Produits (39 000+)

M29W128GL70ZA3E - 128Mb NOR Flash 70ns 64-TBGA | Micron
M29W128GL70ZA3E

M29W128GL70ZA3E - 128Mb NOR Flash 70ns 64-TBGA | Micron

The Micron M29W128GL70ZA3E is a 128 Mbit parallel NOR Flash memory organized as 8M x16 or 16M x8, with a 70 ns access time, operating from a 3V/3.3V supply and housed in a 64-ball TBGA (10x13 mm) package. Parallel NOR Flash is a nonvolatile memory technology in which every cell connects to a bit line, enabling true random access with short read latencies. Within the memory hierarchy, NOR Flash sits as code storage between mask ROM and NAND Flash: unlike NAND, it supports execute-in-place (XIP), allowing a processor to boot directly from the array without copying code to RAM first. It remains the standard boot memory for microcontrollers, DSPs, and FPGAs. Key features of the M29W128GL include the dual x8/x16 bus configuration selected by the BYTE pin, a fast 70 ns access time that supports zero-wait-state reads on many embedded processors, and a 3.0V to 3.6V supply range. The device provides block-protected operation, program/erase via standard command sets, and an industrial operating temperature range of -40C to +125C per Micron product data. Architecturally, the M29W128GL family uses a banked array with boot-block segmentation (the GL suffix denotes the bottom-boot variant; GH denotes top boot), enabling firmware storage with parameter blocks at the boot region. Read, program, and erase operations are controlled through standard bus command sequences with status polling. Typical applications include boot firmware storage for industrial PLCs, telecom line cards, set-top boxes, networking equipment, and automotive-adjacent control modules requiring wide temperature operation. Design-wise, verify VCC decoupling at each supply ball and confirm the BYTE pin is strapped correctly for the chosen bus width, since a floating BYTE pin causes bus contention during boot reads. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
M29W128GL70ZS3F - 128Mb Parallel NOR Flash 70ns | Micron
M29W128GL70ZS3F

M29W128GL70ZS3F - 128Mb Parallel NOR Flash 70ns | Micron

The Micron M29W128GL70ZS3F is a 128 Mbit parallel NOR Flash memory with a 70 ns access time, organized as 16M x 8 or 8M x 16, powered from a single 3V/3.3V supply and housed in a 64-ball FBGA (11x13 mm) package. Parallel NOR Flash is a nonvolatile memory technology that allows random byte-level access over a wide parallel address/data bus, making it suitable for code storage where the processor executes directly from flash (XIP, execute-in-place). In the memory hierarchy, NOR Flash sits alongside SPI NOR and NAND Flash as a nonvolatile storage class; parallel NOR offers the fastest random read latency and the simplest CPU interface, at the cost of higher pin count compared to serial NOR. Key features of this device include the 128 Mbit density, a fast 70 ns random access time for zero-wait-state code execution on many embedded processors, dual x8/x16 bus organization for bus-width flexibility, and an extended operating temperature range of -40C to +125C. The part is AEC-Q100 qualified and marketed by Micron as automotive grade, supporting design reuse in vehicular applications. The uniform 64/64 block architecture referenced by distributors indicates two symmetric partitions for flexible code and data placement. Technically, the M29W128GL family operates from a single 3V to 3.6V VCC supply, uses block-erase program/erase operations with internal state machine control, and provides status signaling for software polling. The 64-ball FBGA (11x13) surface-mount package minimizes board area while supporting the wide parallel bus required for fast random access. Typical applications include automotive ECU boot code storage, industrial PLC firmware, networking equipment boot loaders, and set-top-box or telecom designs that execute code directly from NOR Flash. A key design consideration is supply-rail integrity: verify that the 3.3V rail tolerance and program voltage requirements in the official datasheet match your system before finalizing the power tree. This page synthesizes distributor pricing, drop-in alternative analysis, application guidance, and FAQ content not found in the manufacturer datasheet alone, based on data verified as of 2026-09-05.

Devis Contact
M29W160EB70N3E - 16Mbit NOR Flash 70ns 48-TSOP | Micron
M29W160EB70N3E

M29W160EB70N3E - 16Mbit NOR Flash 70ns 48-TSOP | Micron

The Micron Technology M29W160EB70N3E is a 16 Mbit (2M x8 / 1M x16) 3V parallel NOR Flash memory with a 70 ns access time, supplied in a 48-lead TSOP (48-TFSOP, 0.724 in / 18.40 mm width) package. It operates from a single VCC supply of 2.7V to 3.6V for program, erase, and read operations. Parallel NOR Flash is a nonvolatile memory organized so the host processor can execute code directly from it (XIP, execute-in-place) over a parallel address/data bus. In the memory hierarchy it sits as a boot/code storage device between mask ROM and serial NOR Flash, offering random access over a wide parallel bus rather than a serial SPI interface. NOR Flash remains the standard choice for MCU and processor boot firmware because of its fast random-access latency and byte-level readability. Key features of the M29W160EB family include a 70 ns access time suitable for zero-wait-state code execution, a block-organized architecture with boot-block arrangement, and a 10 microsecond typical programming time per byte/word. The device supports both byte (x8) and word (x16) organization, letting the designer trade data-bus width against address range without changing the PCB. Technically, the device uses a floating-gate NOR cell array with an on-chip state machine that handles program and erase algorithms, status reporting, and data protection. Command-set operation follows the industry-standard M29W command interface, allowing software drivers to poll status rather than time program/erase cycles. Supply range of 2.7V-3.6V matches common 3.3V logic rails directly. Typical applications include boot-firmware storage in industrial controllers, set-top boxes, networking equipment, telecom line cards, and automotive/white-goods control boards where a legacy parallel NOR footprint must be maintained. Design consideration: on 70 ns access-time parts, ensure address setup and output-enable timing in the host memory controller match the -70 speed grade, and keep VCC within 2.7V-3.6V during erase operations since erase voltage margin is tighter than read margin. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
M29W160EB70N3F - 16Mbit NOR Flash, 70ns, 48-TSOP | Micron
M29W160EB70N3F

M29W160EB70N3F - 16Mbit NOR Flash, 70ns, 48-TSOP | Micron

The Micron M29W160EB70N3F is a 16 Mbit (2M x8 / 1M x16) 3V parallel NOR Flash memory with a 70 ns access time, bottom boot block architecture, and a 48-pin TSOP (0.724 in / 18.40 mm width) package supplied in tape and reel packing. It operates from a single VCC supply of up to 3.6V for program, erase, and read operations, and carries AEC-Q100 automotive qualification for harsh-environment deployments. Parallel NOR Flash is a non-volatile memory technology in which each cell connects to a bit line, enabling true random-access reads at the byte or word level. In the memory hierarchy, NOR Flash sits as code-storage memory -> non-volatile memory -> solid-state storage; unlike NAND Flash, its execute-in-place (XIP) capability lets microcontrollers boot directly from the array without first copying code to RAM, which is why parallel NOR remains the default boot memory in automotive ECUs, industrial controllers, and telecom line cards. Key features of the M29W160EB70N3F include the 70 ns address-to-output access time (a 90 ns speed grade also exists in the family), a 10 microsecond typical programming time per word or byte, block-erase architecture with bottom boot blocks for reset/interrupt vector storage, and byte-wide (x8) or word-wide (x16) bus configuration selectable via the BYTE# pin. The common flash interface (CFI) lets programmers auto-detect device geometry and timing. The device is part of the Micron M29W160E family, second-generation 3V NOR Flash built on a mature floating-gate CMOS process. Program and erase commands follow a standard command-set interface compatible with common flash programmers, and the RESET# input restores the device to read mode for fast boot recovery. Automotive-grade screening supports extended temperature operation. Typical applications include automotive powertrain and body-control ECU boot code storage, industrial PLC firmware memory, networking equipment configuration storage, and set-top-box software retention. The parallel interface and 70 ns speed make it a direct fit for legacy bus designs tied to classic microcontrollers. Design consideration: at x16 operation all 16 data lines must be routed with matched length where the CPU clock exceeds 50 MHz; decouple VCC with 100 nF ceramic capacitors at each supply pin. This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in alternatives with package-match verification, and practical design notes in one place.

Devis Contact
M29W160EB80ZA3SE - 16Mb NOR Flash 80ns TFBGA-48 | Micron
M29W160EB80ZA3SE

M29W160EB80ZA3SE - 16Mb NOR Flash 80ns TFBGA-48 | Micron

The Micron Technology M29W160EB80ZA3SE is a 16 Mbit (2M x8 / 1M x16) 3V parallel NOR Flash memory with an 80 ns access time, supplied in a 48-ball TFBGA (6x8 mm footprint, 0.8 mm ball pitch) package. It operates from a 2.7V to 3.6V supply for program, erase, and read operations. Parallel NOR Flash is a nonvolatile memory technology in which every byte is directly addressable over a parallel address and data bus, allowing a processor to execute code in place (XIP) without first copying it to RAM. In the memory hierarchy it sits alongside NAND Flash and serial NOR: NAND offers higher density at lower cost per bit, while parallel NOR offers faster random access, simpler interfacing, and superior reliability, making it a staple of the embedded memory and code storage family. Key features of the M29W160EB include its byte-wide (x8) and word-wide (x16) selectable parallel interface, 80 ns random-access time for zero-wait-state code execution from many microcontrollers, and block-protected boot-block architecture that safeguards resident code from accidental erase. Program and erase operations are commanded through standard JEDEC-style command sets, with status polling and suspend/resume capability that lets the CPU service interrupts during slow erase cycles. Technically, the device uses a single 3V supply rail (2.7V to 3.6V) for all operations, eliminating dual-rail programming supplies required by older 12V-programmed Flash generations. Automotive-grade variants of the M29W160EB family carry AEC-Q100 qualification and support operation from -40C up to +125C, addressing under-hood and mission-critical environments. The TFBGA-48 ball-grid package provides low profile, small footprint, and good thermal and mechanical performance for space-constrained boards. Typical applications include automotive ECU boot code storage, industrial PLC firmware, telecom and networking equipment configuration memory, and set-top box or consumer appliance BIOS storage, where in-place code execution and long-term data retention matter more than raw write bandwidth. A key design consideration: layout for the 0.8 mm-pitch TFBGA requires careful escape routing and signal integrity practice on the parallel address bus; also budget erase time (typically hundreds of milliseconds per block) in your firmware scheduler and use suspend/resume to keep the CPU responsive. This page adds value beyond the datasheet by synthesizing distributor pricing (LCSC from $1.3460), drop-in same-package alternatives, comparison tables, and practical design notes in one engineer-ready reference.

Devis Contact
M29W160ET70N3E - 16Mb 3V Parallel NOR Flash 70ns TSOP48 | Micron
M29W160ET70N3E

M29W160ET70N3E - 16Mb 3V Parallel NOR Flash 70ns TSOP48 | Micron

The Micron M29W160ET70N3E is a 16 Mbit (2 Mbit x8 / 1 Mbit x16) 3V parallel NOR flash memory with a 70 ns access time, housed in a 48-pin TSOP package and qualified to AEC-Q100 for automotive applications. Parallel NOR flash is a nonvolatile memory technology in which the memory array is addressed directly over a parallel address and data bus, allowing a processor to execute code in place (XIP) without first copying it to RAM. Within the memory hierarchy, NOR flash sits alongside DRAM and SRAM as a main-memory-class device and serves as the boot and code-storage medium in automotive ECUs, industrial controllers, and set-top boxes. Its byte-granular random access and long data retention distinguish it from NAND flash, which offers higher density but only page-based access. Key features of the M29W160ET70N3E include the 70 ns random-access speed class for zero-wait-state code execution, a dual 8-bit/16-bit bus configuration selected by the BYTE# pin, and a top boot block architecture (the T in the part number) that places the protected boot code at the top of the memory map. The part number suffix E denotes the RoHS-compliant package with standard packing in tray format. Micron's M29W160E family also offers a bottom boot variant (M29W160EB) for designs whose boot code resides at address 0x000000. Architecturally, the device is organized into uniform blocks with boot blocks, and supports block erase and word/byte program operations with hardware sector protection. The supply operates from a nominal 3V/3.3V rail, and the AEC-Q100 qualification targets the extended temperature ranges typical of under-hood and body-electronics environments. Program and erase automation is handled on-chip, offloading the host microcontroller. Typical applications include automotive ECU boot code storage, industrial PLC firmware, telecom line-card configuration memory, and legacy x16 code-storage upgrades where TSOP48 footprints must be maintained. When designing in this device, verify the boot block location (top versus bottom) matches the processor's reset vector, and confirm the 70 ns access time meets the bus timing at the target VCC corner. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
M29W160ET70N3F - 16Mb 70ns AEC-Q100 NOR Flash | Micron
M29W160ET70N3F

M29W160ET70N3F - 16Mb 70ns AEC-Q100 NOR Flash | Micron

The Micron M29W160ET70N3F is a 16 Mbit (2 M x 8 / 1 M x 16) 3V/3.3V parallel NOR Flash memory with 70 ns access time, AEC-Q100 automotive qualification, and a 48-pin TSOP package supplied in tape-and-reel packing. Decoding the Micron part-number scheme, M29 denotes parallel Flash, 16 the 16 Mb array, T the top-boot block architecture, 70 the 70 ns speed grade, N3 the 48-pin TSOP, and F the RoHS-compliant tape-and-reel packing option. Parallel NOR Flash is a non-volatile memory technology in which the memory cells are connected in parallel, allowing random access to any address in a single access cycle. Within the memory hierarchy, NOR Flash sits alongside DRAM and NAND Flash as a semiconductor memory device; unlike NAND, NOR offers byte-level random access and high reliability, which is why it has long been the dominant choice for code storage (XIP, execute-in-place) in embedded systems. Key features of the M29W160ET70N3F include the 70 ns access time for fast code execution, the flexible x8/x16 bus configuration that lets designers choose between an 8-bit or 16-bit data path, and the top-boot block organization that protects boot code in the highest address blocks. Supply voltage is specified in the 3V/3.3V range per the part description. The device is built on CMOS technology and is AEC-Q100 automotive qualified, meaning it has passed the automotive industry stress-test standard for reliability, supporting temperature-grade requirements typical of in-vehicle applications. Block protection and program/erase operations follow the standard M29W160E family command set. Typical applications include automotive ECU boot-code storage, industrial control firmware, telecom and networking line-card code memory, and embedded systems requiring execute-in-place code storage from a parallel bus. Design consideration: verify the top-boot versus bottom-boot variant against your boot-vector address mapping, since selecting the wrong boot orientation inverts the location of the protected boot blocks. This page synthesizes distributor pricing context, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
M29W160FB70N3E - 16Mb 3V Parallel NOR Flash 70ns | Micron
M29W160FB70N3E

M29W160FB70N3E - 16Mb 3V Parallel NOR Flash 70ns | Micron

The Micron Technology M29W160FB70N3E is a 16 Mbit (2M x8 / 1M x16) 3V parallel NOR Flash memory with a 70 ns access time, housed in a 48-pin TSOP (0.724 in / 18.40 mm width) package. Parallel NOR Flash is a nonvolatile memory technology that allows random access to any byte via a parallel address bus, making it suitable for code storage (XIP - execute-in-place) in embedded systems. Within the memory hierarchy, it belongs to the Flash memory family, alongside NAND Flash and serial NOR (SPI) devices, and is commonly used as the boot memory of a microprocessor-based system because of its fast random read capability and high reliability. Key features of the M29W160FB include a single 3.0 V to 3.6 V supply (VCC) for program, erase, and read operations, 70 ns access time, boot block architecture, and dual x8/x16 bus configurations selected by the BYTE# pin. Block-protected operation and command-set-programming via standard commands simplify firmware drivers. The device uses Micron's advanced NOR Flash cell technology with internal program and erase state machines. Program and erase operations are monitored via data polling and toggle-bit status, allowing simple software integration. Typical block program times and erase times are specified in the manufacturer datasheet. Typical applications include set-top boxes, networking and telecom equipment boot code, industrial control firmware storage, automotive infotainment modules (non-safety), and legacy embedded processor systems requiring parallel NOR. Design consideration: because this is a mature parallel NOR product family, verify lifecycle status and secure a last-time-buy strategy or pin-compatible second source early in new designs. This page synthesizes distributor pricing, drop-in alternatives within the M29W160 family, and practical design notes not found in the manufacturer datasheet.

Devis Contact
M29W320DB80ZA3E - 32Mb Parallel NOR Flash 80ns | Micron
M29W320DB80ZA3E

M29W320DB80ZA3E - 32Mb Parallel NOR Flash 80ns | Micron

The Micron Technology M29W320DB80ZA3E is a 32 Mbit parallel NOR Flash memory organized as 4M x 8 or 2M x 16, with an 80 ns access time, housed in a 63-ball TFBGA (7x11 mm) package operating from a 2.7V to 3.6V supply. Parallel NOR Flash is a non-volatile memory technology that allows random access to any address, making it ideal for storing boot code and firmware that a processor executes directly in place (XIP). Unlike NAND Flash, NOR offers fast random read access and byte-level addressing, sitting within the memory hierarchy as a code-storage device alongside SRAM and DRAM in embedded systems. Key features of the M29W320DB include non-uniform block architecture with boot block organization (the DB suffix denotes bottom boot block), 64 KByte main blocks plus parameter blocks, and a VCC supply of 2.7V to 3.6V for program, erase, and read operations. An optional VPP pin supports a 12V supply for fast program operations. The 80 ns access time supports zero-wait-state execution from slower buses. The device uses Micron (formerly STMicroelectronics/Numonyx) NOR Flash core technology with command-set compatibility to the industry-standard M29W family, including single-word/byte programming, block erase, and status polling via data or toggle bits. Erase suspend/resume allows the host to interrupt block erasure to service read requests, keeping real-time code execution alive during maintenance operations. Typical applications include set-top boxes, automotive instrument clusters and body controllers, industrial PLCs, networking equipment boot firmware, and medical devices where code shadowing or execute-in-place from a reliable parallel NOR device is required. When designing, respect the 80 ns access-time derating across the full automotive temperature range and provide proper VCC decoupling during program and erase, which draw higher transient currents. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
M29W320DT70N3E - 32Mbit NOR Flash 70ns 48-TSOP | Micron
M29W320DT70N3E

M29W320DT70N3E - 32Mbit NOR Flash 70ns 48-TSOP | Micron

The Micron M29W320DT70N3E is a 32 Mbit parallel NOR Flash memory organized as 4M x8 or 2M x16 bits, with a 70 ns access time, operating from a single 2.7 V to 3.6 V supply in a 48-pin TSOP I package. A parallel NOR Flash memory is a non-volatile semiconductor memory in which cells are individually addressable over a parallel address/data bus, allowing random access and direct code execution (XIP) by a microprocessor. Within the memory hierarchy, it sits alongside and complements DRAM (volatile working memory) and NAND Flash (bulk storage): NOR provides fast read latency and byte-level random access, which is why boot code, firmware, and parameter storage have historically been placed in NOR devices. Key features of the M29W320DT include its asymmetrically arranged memory blocks, where a boot region of 64 Kbytes is subdivided into a 16 Kbyte boot block, two 8 Kbyte parameter blocks, and one 32 Kbyte small main block, with remaining capacity in large main blocks. The 70 ns access time supports zero-wait-state code execution from many microprocessors. The device supports read, erase, and program operations from the single low-voltage supply, and programming is performed via standard command-set interfaces familiar to legacy M29W-series designers. Technically, the part is a member of the Micron (ex-STMicroelectronics) M29W320D family; the DT suffix denotes top boot-block architecture, versus DB for bottom boot. The N3E ordering code indicates the 70 ns speed grade, 3 V operating range, TSOP I 48-lead package, and lead-free/ECO packaging revision. Peak reflow time is rated at 30 seconds with Moisture Sensitivity Level 3 (168 hours floor life per AIChipLink product data). Typical applications include microprocessor boot firmware storage in industrial controls, set-top boxes, networking equipment line cards, and telecom modules where code shadowing or XIP is required. The parameter blocks suit configuration and calibration data storage alongside the main firmware region. Design consideration: verify supply decoupling and bus turnaround timing, because at 70 ns the read cycle margin is tight with slow external latches; also confirm block orientation (top boot) matches the CPU reset vector mapping. This page synthesizes distributor pricing, drop-in alternatives, cross-reference findings, and practical design notes not found in the manufacturer datasheet.

Devis Contact
M29W640GB70N3F - 64Mb 70ns Parallel NOR Flash | Micron
M29W640GB70N3F

M29W640GB70N3F - 64Mb 70ns Parallel NOR Flash | Micron

The Micron Technology M29W640GB70N3F is a 64Mb (8 MB) 3V parallel NOR flash memory with x8/x16 data-bus width, 70 ns access time, and an operating voltage range of 2.7V to 3.6V, housed in a 48-lead TSOP I package and qualified to AEC-Q100 for automotive environments with a -40C to +125C operating temperature range. Parallel NOR flash is a nonvolatile memory technology in which every address is directly accessible over a parallel address/data bus, giving deterministic read latency. In the memory hierarchy it sits alongside NAND flash and serial (SPI) flash as a code-storage device; NOR's execute-in-place (XIP) capability and superior random-read speed make it the traditional choice for boot code, firmware, and parameter storage in microcontroller-based systems, whereas NAND targets high-density data storage. Key features of the M29W640GB include the 70 ns access time for fast code fetch, a flexible x8/x16 organization that lets one footprint serve 8-bit or 16-bit buses, 2.7V-3.6V single-supply operation for 3V embedded systems, and automotive AEC-Q100 qualification over the full -40C to +125C temperature span. Block-erase and word/byte program operations are managed via standard command-set interfaces with status polling, easing firmware reuse across the M29W family. Technically, the device uses Micron's floating-gate NOR cell array organized into erase blocks, supporting uniform block architecture (GB variant) suited to in-field firmware update schemes. The parallel interface supports asynchronous reads with CE#, OE#, and WE# control, and the 48-TSOP I surface-mount package keeps the footprint compact for embedded boards. Typical applications include automotive ECU boot flash, industrial programmable logic controller (PLC) firmware storage, telecom and networking equipment code banks, and set-top-box or consumer-appliance firmware memory. When designing with this device, note that the part status is listed as obsolete, so new designs should plan lifetime buy or second-source strategies; verify block-protection and command-set compatibility when substituting family members. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with pricing verified as of 2026-09-05.

Devis Contact
M29W800FT70N3F - 8Mb 70ns Parallel NOR Flash | Micron
M29W800FT70N3F

M29W800FT70N3F - 8Mb 70ns Parallel NOR Flash | Micron

The Micron M29W800FT70N3F is an 8 Mbit (1 Mbit x8 / 512 Kbit x16) 3V parallel NOR Flash memory with a 70 ns access time, supplied in a 48-pin TSOP I package with Tape & Reel delivery. It operates from a 2.7 V to 3.6 V supply across an automotive-grade -40C to +125C temperature range, making it one of the last-generation high-reliability code-storage devices still widely designed into legacy platforms. Parallel NOR Flash is a nonvolatile memory category that stores code and data in NOR cells addressable byte-by-byte or word-by-word over a parallel address/data bus. In the memory hierarchy it sits alongside masked ROM and serial Flash as primary boot memory: CPUs and microcontrollers execute-in-place (XIP) directly from its array, which is why NOR remains preferred for firmware storage even as NAND dominates bulk data storage. Key features of the M29W800FT family include the 70 ns random-access time that supports zero-wait-state execution from slow bus clocking, the flexible x8/x16 bus-width organization selected via the BYTE# pin, and block-protected architecture with temporary unprotect for field firmware updates. The asymmetric T (top boot) block map places the boot blocks with CFI (Common Flash Interface) support for software query of erase/program commands and status. Technically, the device uses a 3 V single-supply EEPROM-array NOR core with automatic program and erase algorithms managed on-chip, eliminating external erase-verify loops. Erase suspend/resume allows reading from one block while erasing another, and the reset/power-down pin (RP#) reduces standby current and provides hardware reset during brown-out events. Typical applications include automotive ECU boot code storage, industrial drives and motor-control firmware, networking equipment configuration storage, and set-top-box or telecom line-card firmware where a parallel bus XIP memory is mandated by the legacy design. A key design consideration is lifecycle: this part is marked obsolete, so new designs should plan a drop-in alternative or last-time-buy stock, and legacy designs must qualify substitutes before re-spins. This page synthesizes verified distributor data, cross-reference results, and drop-in alternative analysis not found on any single distributor page, with pricing as of 2026-09-05.

Devis Contact
M29W800FT70ZA3SF - 8Mbit NOR Flash 70ns TFBGA48 | Micron
M29W800FT70ZA3SF

M29W800FT70ZA3SF - 8Mbit NOR Flash 70ns TFBGA48 | Micron

The Micron M29W800FT70ZA3SF is an 8 Mbit (8 megabit) parallel NOR Flash memory IC with a 70 ns access time, operating from a 2.7 V to 3.6 V supply in a 48-ball TFBGA (6 x 8 mm) package. It is the top-boot-block member of the Micron (formerly STMicroelectronics) M29W800FT family of 3 V parallel NOR Flash devices, rated for operation from -40 C to +125 C. Parallel NOR Flash is a non-volatile memory technology that connects directly to a microprocessor's address and data buses, allowing code to be executed in place (XIP, execute-in-place). Within the memory hierarchy, NOR Flash sits alongside SRAM and DRAM as directly addressable memory, distinguished from NAND Flash and serial SPI Flash by its random-access capability and high read reliability. It remains the standard choice for boot code storage in embedded systems. Key features of this device include the 70 ns access time suitable for zero-wait-state execution on many embedded processors, a 2.7 V to 3.6 V single supply compatible with 3.3 V logic, and 8 Mbit of density organized for byte or word access. The uniform block architecture with boot-block arrangement supports flexible code and data partitioning. Architecturally, the M29W800FT family uses floating-gate NOR cell technology with block-based erase and program operations managed through a command interface. Status polling and toggle-bit schemes allow the host processor to monitor program and erase completion without interrupts. The extended -40 C to +125 C temperature rating targets harsh industrial and automotive-adjacent environments. Typical applications include boot-code storage for embedded microcontrollers and microprocessors, industrial automation controllers, networking equipment firmware, set-top boxes, and telecom line cards where in-place code execution is required. Designers should ensure the 3.3 V supply rail is decoupled locally and observe the block-erase and program timing requirements of the command interface when writing drivers. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet, as of 2026-09-02.

Devis Contact
M2GL005-1FG484 - 6K LEs, 209 I/O FPGA | Microchip
M2GL005-1FG484

M2GL005-1FG484 - 6K LEs, 209 I/O FPGA | Microchip

The Microchip Technology M2GL005-1FG484 is an IGLOO2 flash field-programmable gate array with 6,060 logic elements, 209 user I/O, and a 484-ball plastic BGA package. It operates from a 1.2 V core supply and is designed for compact programmable-logic designs requiring substantial I/O density. The M2GL005-1FG484 combines nonvolatile FPGA configuration, reusable logic fabric, and integrated programmable I/O in a surface-mount package suitable for industrial control, communications, bridging, and embedded system-management equipment. An FPGA is a programmable semiconductor in which the logic interconnect and digital functions can be configured after fabrication. The M2GL005 belongs to the IGLOO2 family, which combines low-density flash FPGA resources with general-purpose logic functions. Within the product hierarchy, it is an FPGA, then a programmable-logic IC, then a semiconductor. This positioning makes the device useful when fixed-function logic would require excessive board space or frequent redesign. The IGLOO2 architecture provides 6,060 logic elements and 209 I/O, giving the design substantially more external connectivity than a small programmable logic device. Its flash configuration technology allows the programmed function to be retained without a separate configuration PROM. A 484-BGA package also supports dense routing and fine-pitch PCB layouts, although it requires careful escape-routing and assembly planning. M2GL005 devices are intended for functions such as protocol bridging, I/O expansion, signal conversion, system management, and secure connectivity. The 209-I/O count can consolidate parallel digital interfaces, control interfaces, and communications logic into one device. Because the target package contains 484 balls, its electrical performance depends on correct bank voltage planning, clean power distribution, and controlled rise time across all supply rails. The 1.2 V core requirement makes board-level sequencing important in systems that also operate external interfaces at higher voltages. Designers should use the manufacturer pin-description tables when assigning every ball, especially configuration pins, dedicated pins, banks, and supply pins. The IGLOO 2 packaging and pin-description guide referenced by Microchip is the appropriate document for PCB land patterns and bank assignments. For new layouts, follow the package-specific ball map rather than relying on a generic BGA symbol. Place decoupling capacitors at every supply ball where the recommended layout permits, route high-speed nets with short return paths, and preserve the 1.0 mm terminal pitch shown for this package family. Programming, configuration density, clocking, and I/O standards must be checked against the exact device variant before schematic release. This page combines the manufacturer product information, package and pin documentation, sourced replacement options, and application-specific design guidance. It also distinguishes the IGLOO2 M2GL005 options by package suffix and qualification coding, helping engineers identify a board-compatible replacement without overlooking device-temperature, speed-grade, or qualification requirements.

Devis Contact
M2GL005-1TQ144 - 6060-LE 1.2V IGLOO2 FPGA | Microchip
M2GL005-1TQ144

M2GL005-1TQ144 - 6060-LE 1.2V IGLOO2 FPGA | Microchip

The Microchip Technology M2GL005-1TQ144 is an IGLOO2 low-density field-programmable gate array with 6,060 logic elements, 719,872 bits of RAM, and 84 user I/O pins. The device operates from a 1.2 V core supply and is packaged in a 144-pin TQFP measuring 20 mm by 20 mm, making it suitable for compact programmable-logic designs requiring substantial routing resources and mixed I/O capacity. An FPGA is a reconfigurable digital semiconductor that can be programmed after fabrication to implement logic, state machines, interface controllers, and signal-processing functions. The IGLOO2 family belongs to the broader low-density programmable-logic hierarchy and combines FPGA fabric, programmable I/O, embedded RAM, and configuration resources in one device. This makes the M2GL005-1TQ144 useful where a microcontroller or discrete logic would require extensive firmware and supporting circuitry. Key device attributes include 6,060 logic cells, 719,872 total RAM bits, and 84 I/O pins in a 144-TQFP package. The 1.2 V operating voltage supports modern low-energy digital systems, while the large pin count provides broad connectivity to external memory, sensors, communications devices, and mixed-signal components. Microchip lists the M2GL005 family as in production, supporting its use as the foundation of general-purpose programmable-logic platforms. The IGLOO2 architecture supports parallel programmable logic and reusable on-chip RAM, allowing designers to implement datapath logic, protocol adapters, control logic, and fixed-function subsystems without relying on an external processor. The 84 available I/O pins make the 144-TQFP option particularly useful where multiple buses or mixed signal interfaces must connect directly to the FPGA. Its 20 mm by 20 mm surface-mount package also avoids the mechanical complexity of larger ball-grid-array FPGA packages. Typical uses include industrial control and factory automation, communications infrastructure, embedded system management, I/O expansion, and secure connectivity. The device can bridge dissimilar interfaces, translate protocols, consolidate control functions, or implement parallel data acquisition logic. Its large I/O count is especially useful for systems requiring multiple chip-select, address, control, and serial signals without adding another external bus controller. PCB design should follow Microchip's package and power-supply recommendations, including short, properly decoupled core and I/O supply connections and careful assignment of sensitive pins. Because the complete numbered pin map is not published in the accessible product results, use the manufacturer package drawing and pin-description table before assigning tracks, power rails, or programming signals. This page combines the exact M2GL005-1TQ144 device specifications, lifecycle information, same-package alternatives, comparison criteria, and practical selection guidance to support FPGA sourcing and design decisions.

Devis Contact
M2GL005-1VF256 IGLOO2 FPGA, 6060 LEs, 161 I/O, 256-FBGA | Microchip
M2GL005-1VF256

M2GL005-1VF256 IGLOO2 FPGA, 6060 LEs, 161 I/O, 256-FBGA | Microchip

The Microchip Technology M2GL005-1VF256 is an IGLOO2 low-density FPGA built on a 1.2 V flash-programmable fabric, delivering 6,060 logic cells with 161 user I/O in a 256-ball FBGA (VF256) package. It targets general-purpose logic, bridging, I/O expansion, system management and secure connectivity designs where a low-power, small-footprint programmable logic device is preferred over a microcontroller or discrete glue logic. A field-programmable gate array is a reconfigurable digital integrated circuit whose logic fabric, interconnect and I/O blocks are defined after manufacture by a bitstream downloaded from flash. The IGLOO2 family from Microsemi/Microchip is a low-density, non-volatile flash FPGA line positioned between mask-programmable ASICs and larger, higher-cost FPGAs, giving designers a fast path to volume production without a foundry mask set. Key characteristics of this device include 6,060 logic cells, 161 user I/O, a 1.2 V core operating voltage, and on-chip non-volatile configuration memory so the design is retained without an external configuration PROM. Because the configuration is stored in flash, the part powers up directly into the user's logic with no wait-state configuration sequence from an external master, which simplifies board design and reduces BOM cost. The IGLOO2 architecture provides a mix of programmable logic and dedicated I/O resources, allowing parallel interface bridging, bus conversion, protocol translation and simple control-plane logic to be consolidated into a single device. The 256-ball FBGA package with 0.8 mm ball pitch keeps the footprint small enough for space-constrained industrial, communications and consumer-adjacent equipment, while offering more I/O than a quad flat pack would provide. Typical applications include I/O expansion and level translation between legacy and modern systems, industrial sensor and instrument signal conditioning, secure connectivity and authentication front ends, communications infrastructure bridging, and general system-management supervision logic in industrial and commercial equipment. When designing around this device, keep the 1.2 V core rail well filtered and decoupled, and place the 0.8 mm pitch BGA on a board whose escape-routing rules are checked against the IGLOO 2 packaging and pin description user guide before layout sign-off. This page brings together the manufacturer device page, distributor availability data, package and pin references, drop-in alternatives in the same 256-ball footprint, and practical design notes that are not consolidated in a single manufacturer document.

Devis Contact
M2GL005-1VF400 - 6K LEs, 169 I/O IGLOO2 FPGA | Microchip
M2GL005-1VF400

M2GL005-1VF400 - 6K LEs, 169 I/O IGLOO2 FPGA | Microchip

The Microchip Technology M2GL005-1VF400 is an IGLOO2 low-density field-programmable gate array with 6K logic elements, 169 I/O, and a 400-LFBGA package. It is a programmable semiconductor used to implement bridging, I/O expansion, data conversion, system management, and secure connectivity functions. The -1 suffix identifies the device speed grade, while VF400 denotes its 400-ball package configuration. An FPGA is a reconfigurable digital integrated circuit whose logic, interconnect, and I/O functions can be programmed after manufacture. Within the semiconductor hierarchy, the M2GL005-1VF400 belongs to the FPGA and CPLD class, using configurable logic blocks, programmable routing resources, memory, and I/O blocks. Compared with fixed-function logic ICs, this architecture allows design changes, field updates, and implementation of multiple control functions in one device. The device provides approximately 6K logic elements and 169 I/O, making it suitable for low-density bridging, protocol conversion, peripheral interconnection, and embedded control tasks. Its 400-LFBGA package supports a high connection count for designs requiring substantial external signal access. The manufacturer identifies the M2GL005 family as being in production and recommends it for communications, industrial, and general-purpose programmable-logic applications. The IGLOO2 architecture integrates programmable logic with embedded memory and configurable I/O. Engineers can map counters, state machines, datapaths, communication interfaces, and control functions into a compact device while retaining the flexibility to revise logic through reprogramming. Exact core voltage, memory capacity, supported I/O standards, and operating-temperature limits must be confirmed in the manufacturer datasheet before final schematic and timing closure. Typical applications include industrial protocol bridges, embedded serial-interface adapters, I/O expansion, platform management logic, and secure-connectivity controllers. It is also appropriate for compact control modules that need parallel logic alongside programmable serial communication. Designs requiring higher logic density or numerous high-speed interfaces should be compared with larger IGLOO2 devices before committing the PCB footprint. The principal hardware considerations are BGA escape routing, clean power and ground distribution, decoupling, and signal-integrity validation. Because the package exposes 400 balls, use the manufacturer's pin-information guide and package drawings for power, ground, configuration pins, and I/O placement. Preserve the prescribed configuration interface and program the device through a supported toolchain or embedded programming solution. This page combines package, device-family, application, and replacement context with practical guidance for schematic capture, layout, programming, and migration decisions. It helps engineers distinguish electrically similar M2GL005 variants by package, grade, temperature designation, and qualification rather than treating every similarly named orderable part as a drop-in substitute.

Devis Contact
M2GL005-FG484 - 6K LEs, 209 I/O IGLOO2 FPGA | Microchip
M2GL005-FG484

M2GL005-FG484 - 6K LEs, 209 I/O IGLOO2 FPGA | Microchip

The Microchip Technology M2GL005-FG484 is an IGLOO2 low-density flash FPGA with 6,060 logic elements, 209 user I/O, and a 484-BGA package. The device operates from a 1.2 V core supply and is supplied in a 23 mm × 23 mm, 1.0 mm-pitch surface-mount package according to the verified product listings. It targets general-purpose programmable logic, I/O expansion and conversion, system management, secure connectivity, communications, industrial, medical, defense, and aviation applications. An FPGA is a programmable semiconductor containing configurable logic, memory, and programmable I/O. Within the product hierarchy, the M2GL005-FG484 is a field-programmable gate array, a low-density FPGA, and a member of Microchip's IGLOO2 family. Its flash-based configuration allows the device to retain its programmed logic after power is removed, reducing the need for external configuration memories in standalone control or bridging systems. The verified data identifies 209 user I/O and 6,060 logic elements, providing substantial interface density for conversion, bridging, control, and system-management functions. The FG484 package supports high-pin-count board layouts while keeping the component compact at 23 mm × 23 mm. Compared with a smaller FPGA package, the principal advantage is I/O accessibility; compared with a larger FPGA, the M2GL005 provides a lower logic capacity and a simpler implementation target. Microchip positions IGLOO2 devices for bridging functions, I/O expansion and conversion, system management, secure connectivity, Gigabit Ethernet or dual PCI Express control planes, and video or image processing. These applications benefit from deterministic hardware logic, parallel interface handling, and reconfigurable hardware that can be updated without replacing the assembled board. The 1.2 V core supply makes board-level power design sensitive to ripple, sequencing, and decoupling. A 484-BGA device also demands careful escape routing, multilayer PCB construction, and thermal-aware via distribution. The M2GL005-FG484 is therefore appropriate for engineers who need a large, configurable I/O surface in a low-density, nonvolatile FPGA rather than the larger programmable resources of a high-end FPGA. This page combines verified distributor availability, manufacturer application positioning, same-package alternatives, and practical design considerations for evaluating the Microchip M2GL005-FG484 in communications, industrial, medical, defense, and aviation systems.

Devis Contact
M2GL005-FG484I - 6K LEs, 209 I/O, 1.2V IGLOO2 | Microchip
M2GL005-FG484I

M2GL005-FG484I - 6K LEs, 209 I/O, 1.2V IGLOO2 | Microchip

Microchip Technology M2GL005-FG484I is an IGLOO2 flash field-programmable gate array with 6,060 logic cells, 209 user I/O, and a 1.2 V core in a 484-ball BGA package. It belongs to the low-density IGLOO2 family and combines programmable logic with embedded flash configuration memory for standalone FPGA designs. The device targets general-purpose logic functions including bridging, I/O expansion, protocol conversion, system management, and secure connectivity. An FPGA is a programmable-logic semiconductor whose interconnection and logic resources are configured after manufacture. In the product hierarchy, the M2GL005-FG484I is an FPGA, a programmable-logic device within the broader category of integrated circuits. Compared with a fixed-function application-specific integrated circuit, an FPGA allows design revisions, field updates, and hardware customization without changing the PCB. Its embedded flash supports nonvolatile configuration retention, which is useful where the completed design must operate without an external configuration loader. The M2GL005-FG484I provides 6,060 logic cells and 209 I/O in the industrial-temperature ordering identified by the I suffix. Its 1.2 V core supply is indicated in the component listing, while the 484-BGA package supports dense PCB routing and a large perimeter and ball-field connection arrangement. These characteristics make the device suitable for control-plane logic, interface bridging, signal conversion, embedded system management, and communication equipment requiring programmable logic rather than a fixed microcontroller function. The IGLOO2 family is positioned for low-density designs where logic capacity, I/O availability, nonvolatile configuration, and package density matter more than a very large programmable fabric. Compared with the larger IGLOO2 members appearing in the same family, the M2GL005 option favors compact system integration and lower logic demand. Designers must still partition available logic and I/O according to the complete Microchip pin-description guide before committing a board layout or pin assignment. Typical applications include communications infrastructure, industrial control, medical equipment, defense systems, and aviation electronics. In a bridge or protocol converter, parallel or serial interfaces can be combined in parallel logic blocks and interconnected through the FPGA fabric. In system-management designs, the same nonvolatile platform can implement monitoring, control, alarm handling, and auxiliary I/O expansion while retaining its configuration after power removal. A practical design consideration is the 484-BGA footprint: ball assignment, bank voltage compatibility, configuration pins, power rails, and decoupling must follow the manufacturer packaging guide rather than assumptions based on another IGLOO2 package. The M2GL005 family supports secure-connectivity and general-purpose programmable functions, but design security and programming workflow must be evaluated separately from the core logic capacity and I/O count. This product page consolidates the verified device identity, family positioning, package information, sourcing context, compatible same-brand ordering variants, and engineering-focused selection guidance. It also distinguishes true package-matched options from larger IGLOO2 devices that may require design changes and therefore are not treated as drop-in replacements.

Devis Contact
M2GL005-FGG484 - 6,060-Cell 1.2V FPGA | Microchip Technology
M2GL005-FGG484

M2GL005-FGG484 - 6,060-Cell 1.2V FPGA | Microchip Technology

Microchip Technology M2GL005-FGG484 is an IGLOO 2 flash field-programmable gate array with 6,060 logic cells, a 1.2 V core supply, and a 484-ball FBGA package. The device is intended for general-purpose programmable logic, bridging, I/O expansion, protocol conversion, system management, and secure connectivity functions. Its 23 x 23 mm package uses a 1 mm ball pitch and surface-mount construction. An FPGA is a programmable-logic semiconductor whose lookup tables, registers, memory blocks, and I/O resources can be configured after manufacture. Within the product hierarchy, the M2GL005-FGG484 is an IGLOO 2 flash FPGA, placing it between a general-purpose programmable-logic device and a larger embedded system-on-chip. Flash configuration allows the device to retain its programmed logic without a separate external configuration memory. Key features of this M2GL005 device include 6,060 logic cells, 1.2 V operation, a 484-ball FBGA package, and a square 23 x 23 mm body. The large pin and ball count provides extensive connectivity for high-pin-count designs, while the low-density IGLOO 2 configuration provides a practical option for bridging, conversion, control, and auxiliary processing functions. Microchip positions the IGLOO 2 family for communications, industrial, medical, defense, and aviation applications. The FGG484 package designation identifies the 484-ball package configuration, while the M2GL005 device family provides 6,060 programmable logic cells. The supplied programming files and pin assignments must match the exact device, package, speed grade, and temperature grade selected. Before schematic capture or PCB layout, engineers should consult the IGLOO 2 Packaging and Pin Descriptions User Guide for bank assignments, dedicated pins, power requirements, and package mechanics. Typical uses include protocol bridging, industrial interface conversion, secure connectivity, control-plane logic, data acquisition, and low-power embedded preprocessing. The device can also implement parallel-to-serial conversion, I/O expansion, or system-management functions when a programmable architecture offers more flexibility than fixed-function logic. Its large BGA footprint supports designs requiring many high-speed or differential I/O resources. For a new layout, treat the BGA ball field, power grid, decoupling, configuration interface, clocking, and I/O standards as a complete design task. Follow the manufacturer’s recommended land pattern, ball assignment, and layer-stack guidance. Validate signal integrity and power integrity with the selected Vivado or Libero design flow before releasing the board for fabrication. This product record combines the exact device identity, package characteristics, documented application directions, drop-in replacement candidates, and practical implementation considerations. It is intended to help engineers evaluate mechanical compatibility, programming constraints, application fit, and sourcing requirements before committing the M2GL005-FGG484 to a PCB design.

Devis Contact
M2GL005-TQ144 6K IGLOO2 Flash FPGA | Microchip
M2GL005-TQ144

M2GL005-TQ144 6K IGLOO2 Flash FPGA | Microchip

The Microchip Technology M2GL005-TQ144 is a low-density IGLOO2 flash field-programmable gate array with 6,060 logic elements, 1.2 V operation, and a 144-pin TQFP package. It is designed for general-purpose programmable logic, bridging, I/O expansion, signal conversion, and system-management functions. An FPGA is a programmable semiconductor whose logic fabric can be configured after manufacture. Within the product hierarchy, the M2GL005-TQ144 is an IGLOO2 device, then a low-density flash FPGA, then a programmable-logic IC and semiconductor. Its flash configuration memory allows the device to retain its programmed configuration, while its programmable I/O and logic resources support interfaces that would otherwise require multiple fixed-function components. The verified product data identifies 6,060 FPGA cells, a 1.2 V core voltage, and a 144-pin LQFP/TQFP package. The related M2GL005 comparison data also identifies 703 Kbit of fabric RAM and 128 Kbit of embedded nonvolatile memory for the M2GL005 family. Exact device-specific operating-temperature, I/O-standard, speed-grade, and electrical details should be confirmed in the Microchip IGLOO2 datasheet before release to production. Compared with an equivalent CPLD, the IGLOO2 architecture provides substantially greater logic capacity and flexible routing for multi-block control logic. It is suitable for communications, industrial, and embedded applications where parallel interfaces, protocol bridging, acquisition support, or supervisory logic must be consolidated into one programmable device. Typical implementations include dual PCI Express control-plane functions, Gigabit Ethernet bridging, serial-to-parallel data conversion, I/O expansion, and centralized system management. The 144-pin package provides a practical balance between programmable I/O availability and board-space requirements for compact embedded systems. For layout, follow the Microchip IGLOO2 pin and package documentation for bank assignments, pin constraints, and supported voltage standards. Configuration, programming, JTAG, and power-up behavior must also be checked against the system clocking and reset architecture rather than inferred from the distributor listing.

Devis Contact
M2GL005-TQ144I - 6060-Cell 1.2V FPGA | Microchip Technology
M2GL005-TQ144I

M2GL005-TQ144I - 6060-Cell 1.2V FPGA | Microchip Technology

The Microchip Technology M2GL005-TQ144I is an IGLOO2 flash-based field-programmable gate array with 6060 logic cells, a 1.2 V operating voltage, and a 144-pin TQFP package. It is designed for general-purpose programmable logic, bridging, I/O expansion, data conversion, system management, and secure connectivity implementations. The device combines reconfigurable logic resources with embedded flash configuration memory in a surface-mount package suitable for industrial and commercial PCB assemblies. An FPGA is a programmable-logic semiconductor whose digital circuits are defined by a configuration bitstream rather than fixed mask programming. Within the product hierarchy, the M2GL005 belongs to the IGLOO2 family of low-density FPGAs, which sit below higher-capacity programmable-logic devices and are commonly used as coprocessors, interface conditioners, system-control engines, or I/O concentrators. The M2GL005-TQ144I combines approximately 6000 logic elements with a 144-pin package to provide a practical balance of routing capacity, I/O availability, and board space. The device is identified as a 1.2 V IGLOO2 FPGA with 6060 cells. Its embedded flash configuration technology allows the implemented logic to be retained in the device, which is useful in systems that require reconfigurable peripherals, field updates, or application-specific digital functions without external configuration memory. The TQFP-144 package also provides a familiar leaded footprint for manufacturing processes that do not require an ultra-fine-pitch BGA package. Microchip identifies the IGLOO2 family as suitable for communications, industrial, and embedded applications where bridging, I/O expansion, conversion, system management, and secure connectivity functions are required. A typical design places the FPGA beside one or more interface controllers, connects it to sensors, displays, memory, or communications transceivers, and loads its configuration through a programmer or an in-system programming path. The exact logic-cell organization, supported I/O standards, configuration interface, and performance grades must be checked in the manufacturer datasheet for the selected device variant. One important design consideration is that the TQFP-144 footprint consumes more board area and has finer lead pitch than many modern BGA or QFN options. Designers should preserve access to all 144 pads, maintain suitable copper and solder-mask geometry, and route configuration signals away from sensitive analog or high-speed interfaces. Power, ground, decoupling, and unused-pin treatment should follow the manufacturer’s device-specific recommendations. This product page combines the exact M2GL005 family identifiers, package information, sourcing details, technical alternatives, application guidance, and PCB-focused design notes. It helps engineers identify whether the 144-pin IGLOO2 device provides the required logic density and can be substituted without changing the board footprint.

Devis Contact
M2GL005-TQG144 - 6K LEs, 1.2V IGLOO2 FPGA | Microchip
M2GL005-TQG144

M2GL005-TQG144 - 6K LEs, 1.2V IGLOO2 FPGA | Microchip

The Microchip Technology M2GL005-TQG144 is a low-density IGLOO2 flash field-programmable gate array with 6,060 logic elements, a 1.2 V operating voltage, and a 144-pin TQFP package. It is designed for compact programmable-logic, bridging, I/O expansion, system-management, secure-connectivity, and general-purpose control functions where nonvolatile FPGA configuration and deterministic hardware logic are useful. An FPGA is a user-programmable semiconductor whose logic fabric, I/O, memory blocks, and dedicated resources can be configured after manufacture. The M2GL005 belongs to the IGLOO2 low-density FPGA hierarchy, where flash configuration integrates the control subsystem and programmable logic into one package. Compared with a discrete microcontroller plus supporting logic, it can consolidate parallel interfaces, protocol bridging, data acquisition, and control functions in a single device. The verified device data identifies 6,060 logic elements, a 1.2 V operating voltage, 703 Kbit of fabric RAM, and 64 KB of embedded SRAM. It is supplied in a 144-pin TQFP package measuring 20 x 20 mm with a 0.5 mm lead pitch. The package provides substantially more I/O and board-space flexibility than smaller FPGA packages, making the device appropriate for medium-complexity systems requiring numerous external connections. IGLOO2 devices combine programmable logic with dedicated flash configuration and memory resources. The 6K logic-element fabric is aimed at general-purpose functions rather than processor-heavy workloads. Available architecture details such as exact I/O standards, supported clock frequencies, voltage tolerances, and extended-temperature limits must be confirmed in the applicable Microchip datasheet and package documentation before schematic or timing closure. Typical uses include interface conversion, industrial control, communications support, medical equipment, defense systems, and embedded logic platforms. The large TQFP package can simplify fanout between an FPGA and discrete interface components, while the flash-based architecture eliminates a separate configuration PROM for designs supported by the device configuration flow. Designers should evaluate available I/O standards, core-voltage requirements, configuration pins, clock topology, and exposed power pins against the complete datasheet. A conservative power and pinout review is essential because the target data confirms the 1.2 V operating voltage but does not provide every pin name or bank-level electrical limit. This page combines verified manufacturer and distributor information, same-package replacement analysis, practical engineering guidance, and application-oriented selection criteria to provide engineering context beyond a basic distributor listing.

Devis Contact
M2GL005-VF256 - IGLOO2 5K FPGA, 256-BGA | Microchip
M2GL005-VF256

M2GL005-VF256 - IGLOO2 5K FPGA, 256-BGA | Microchip

The Microchip Technology M2GL005-VF256 is an IGLOO2 flash field-programmable gate array with 5K logic elements, 161 I/O, and a 256-LFBGA package. The verified distributor record identifies the device as an IGLOO2 FPGA and provides the 256-LFBGA package designation. Its programmable logic resources support general-purpose bridging, I/O expansion and conversion, system management, secure connectivity, and embedded control functions. An FPGA is a reconfigurable semiconductor in the programmable-logic and semiconductor hierarchy. Unlike a fixed-function application-specific integrated circuit, an FPGA combines programmable logic, programmable interconnect, and configurable I/O in one device. This makes it useful when interfaces, control sequences, or product requirements evolve faster than fixed hardware can be changed. The M2GL005-VF256 is positioned as a low-density IGLOO2 device. The verified product page identifies IGLOO2 FPGAs for communications, industrial, medical, defense, and aviation markets, including functions such as Gigabit Ethernet or dual PCI Express control planes, bridging, I/O expansion and conversion, video and image processing, system management, and secure connectivity. The exact logic-cell count, voltage, speed grade, memory, package dimensions, and temperature grade for this exact suffix are not provided in the verified excerpts. Because the MPN suffix identifies the device ordering configuration, engineers should confirm the full electrical, pin, package, and temperature details in the manufacturer IGLOO2 datasheet and package documentation before release to production. The verified cross-reference results also identify the IGLOO2 pin-information user guide and the board and layout design guidelines as relevant design references. Typical uses include protocol bridging, industrial control, communications interfaces, image or video processing, and embedded system-management logic. The 256-LFBGA package favors compact designs but requires careful ball assignment, power planning, signal-integrity review, and thermal assessment. A board-level design should follow Microchip application note AN4153, which describes PCB design guidance for SmartFusion 2 and IGLOO2 devices. This page combines the verified Microchip product identity, distributor package information, official datasheet references, and design-document links into an application-oriented record. Exact electrical ratings and commercial pricing remain marked for validation because the supplied data does not provide those values.

Devis Contact