Circuits intégrés d'interface
Sous-catégories
Produits (1568)
TMUX136RSER - 6GHz 2-Ch SPDT Analog Switch | TI UQFN-10
The Texas Instruments TMUX136RSER is a high-performance 6-GHz, 2-channel, 2:1 (SPDT) analog switch with powered-off protection, packaged in a 10-pin UQFN (RSE, 2.0 x 1.5 mm) and rated for a typical on-resistance of 9.5 ohm. It supports a wide VCC range of 2.3 V to 4.8 V and offers 1.4 pF typical on-state capacitance, making it ideal for high-frequency signal multiplexing. What is an analog switch/multiplexer? An analog switch (also called a multiplexer or MUX) is a solid-state semiconductor device that routes analog or digital signals between multiple input/output paths under digital control, using MOSFET transistors as the switching elements. Analog switches sit within the broader hierarchy of interface ICs -> signal routing -> semiconductor ICs. The 2:1 (SPDT) configuration means each of the two independent channels can connect a common pin to one of two possible inputs, a topology commonly used for signal multiplexing, source selection, and USB/MIPI/LVDS switching. Key features include a -3 dB bandwidth of 6 GHz, 1.4 pF on-state capacitance (Con), 9.5 ohm typical on-resistance (Ron), and 1.8 V-compatible control inputs that interface directly with low-voltage processor GPIOs. Power-off protection forces all I/O pins into high-impedance mode when VCC is removed, protecting downstream components and preventing back-powering through the signal path. The flow-through pinout places inputs and outputs on opposite sides of the package, simplifying PCB routing. The architecture uses N-channel MOSFET pass transistors driven by a charge-pump-assisted gate driver, which achieves low Ron flatness across the input signal range and supports bidirectional signal paths. The 6 GHz bandwidth enables pass-through of high-speed differential protocols such as USB 2.0, MIPI DSI/CSI, and LVDS without significant insertion loss. Typical applications include tablet and notebook signal multiplexing, smartphone MIPI/DSI switching, USB 2.0 high-speed signal routing, and audio signal path selection. The device also finds use in test equipment and instrumentation where high-bandwidth signal multiplexing is required. When designing with this device, observe the absolute maximum ratings for analog signal voltage. Use controlled-impedance PCB traces (typically 50 ohm single-ended or 90 ohm differential) for high-frequency signals to preserve signal quality at the rated 6 GHz bandwidth. This page synthesizes distributor pricing, drop-in alternatives from TI and competitors, and practical design notes not found in the manufacturer datasheet alone.
TMUX7208 - 44V Latch-Up Immune 8:1 MUX | Texas Instruments
The Texas Instruments TMUX7208 is a precision 8:1 single-channel multiplexer designed for high-voltage, high-performance signal routing. It operates from a single supply of 4.5V to 44V, dual supplies of ±4.5V to ±22V, or asymmetric supplies such as VDD=12V and VSS=-5V. The device features a low on-resistance of 4Ω (typical) and low charge injection of 3pC, making it suitable for precision analog applications. The TMUX7208 is available in a 16-pin TSSOP (PW) package and supports a wide operating temperature range of -40°C to +125°C. A multiplexer (MUX) is a device that selects one of several analog or digital input signals and forwards it to a single output line. The TMUX7208 is an analog multiplexer, specifically an 8:1 configuration, meaning it routes one of eight input channels to a common output based on the state of three address pins and an enable pin. This functionality is essential in data acquisition systems, test equipment, and industrial automation where multiple sensors or signals need to be sampled sequentially by a single ADC or measurement circuit. Key features of the TMUX7208 include latch-up immunity, which prevents damage from overvoltage or ESD events, and 1.8V logic-compatible inputs, allowing direct interface with low-voltage microcontrollers without level shifters. The device supports high current up to 300mA (max), making it robust for various loads. The low on-resistance and charge injection ensure minimal signal distortion and glitches during switching. The TMUX7208 uses a precision architecture with a break-before-make switching mechanism, preventing momentary shorting between channels. The device also features an enable pin that, when low, disconnects all channels, providing a high-impedance state. This is useful for power-down or isolation scenarios. The wide supply range and latch-up immunity make it ideal for industrial and automotive environments where voltage transients are common. Typical applications include data acquisition systems, test and measurement equipment, industrial process control, and battery monitoring systems. The TMUX7208 can be used to multiplex multiple sensor inputs into a single ADC, reducing component count and cost. Its high-voltage capability allows direct connection to 24V industrial buses without additional level shifting. When designing with the TMUX7208, ensure that the supply voltages are within the specified range and that the input signals do not exceed the supply rails. Proper decoupling capacitors on the supply pins are recommended to minimize noise. The address and enable pins should be driven with logic levels compatible with 1.8V to 5V, as the device is 1.8V logic compatible.
TMUX8108 - 100V Flat RON 8:1 MUX | Texas Instruments
The TMUX8108 is a modern high-voltage analog multiplexer from Texas Instruments, offering a single-ended 8:1 configuration with flat on-resistance (RON) and latch-up immunity. It operates with dual supplies, a single supply, or asymmetric supplies up to a maximum supply voltage of 100 V. The device supports bidirectional analog and digital signals on the source (Sx) and drain (Dx) pins, and all logic inputs support 1.8 V, 3.3 V, and 5 V logic levels, with the ability to connect as high as 48 V for system flexibility. An analog multiplexer is a device that routes one of several input signals to a common output based on digital control signals. In a single-ended 8:1 configuration, the TMUX8108 selects one of eight input channels and connects it to a single output. This functionality is essential in data acquisition systems, test equipment, and industrial automation where multiple sensors or signals need to be sampled sequentially by a single ADC or measurement circuit. The multiplexer acts as a signal router, enabling efficient use of expensive analog-to-digital converters and reducing component count. Key features of the TMUX8108 include a flat RON of 50 ohm, which minimizes distortion and ensures consistent performance across the input voltage range. The device provides latch-up immunity, preventing damage from overvoltage or overcurrent conditions. It supports a wide supply range up to 100 V, making it suitable for high-voltage industrial and automotive applications. The logic inputs are compatible with 1.8 V, 3.3 V, and 5 V systems, allowing direct interface with modern microcontrollers without level shifters. Technically, the TMUX8108 is built on a high-voltage CMOS process that enables low leakage currents and fast switching times. The flat RON characteristic is achieved through careful design of the switch architecture, ensuring that the on-resistance remains nearly constant across the entire analog input range. This reduces signal distortion and improves accuracy in precision measurement systems. The device also features break-before-make switching to prevent momentary shorting of channels during transitions. Typical applications include data acquisition systems, automated test equipment, industrial process control, and battery monitoring systems. In data acquisition, the TMUX8108 allows a single ADC to sample multiple sensor channels, reducing cost and board space. In battery monitoring, it can route individual cell voltages to a measurement circuit, enabling accurate state-of-charge estimation. The high-voltage capability makes it ideal for automotive 48 V systems and industrial 24 V or 48 V buses. When designing with the TMUX8108, ensure that the supply voltages are within the absolute maximum ratings and that the logic control signals are properly referenced to the logic supply. The device requires careful PCB layout to minimize parasitic capacitance and maintain signal integrity, especially in high-frequency applications. Additionally, consider the on-resistance and leakage current when calculating system accuracy, as these parameters affect the overall measurement error.
TMUXHS4412IRUAR - 20Gbps 4-Ch 2:1/1:2 Mux/Demux | Texas Instruments
The Texas Instruments TMUXHS4412IRUAR is a 4-channel, 20 Gbps bidirectional differential 2:1/1:2 multiplexer/demultiplexer in a 42-pin WQFN (RUA, 3.5 mm x 9 mm) package with exposed thermal pad, providing an 8 ohm on-state resistance and a typical -3 dB bandwidth of 13 GHz across each high-speed lane. The device supports USB 3.2 Gen 2x2, USB 3.2 Gen 1, USB 2.0, DisplayPort 1.4, SATA, PCIe Gen 3, SAS, and MIPI DSI/CSI by routing two differential sources to a single differential sink or vice versa with sub-130 ns propagation delay and 50 ps intra-pair skew. A high-speed multiplexer/demultiplexer (mux/demux) is a passive analog switch that selects one of multiple differential input pairs to a single output pair, enabling a host controller to share one PHY across two connectors, two PHYs across one connector, or to switch between redundant high-speed data paths. In the signal chain hierarchy the mux/demux sits between the protocol physical layer (PHY) and the connector, providing galvanic isolation between channels while preserving signal integrity at multi-gigabit NRZ and PAM3/PAM4 signaling rates. The TMUXHS4412 implements bidirectional switching so the same device serves either mux (2:1) or demux (1:2) topology without firmware configuration. Key differentiating features include 20 Gbps per-channel data rate (enabling USB 3.2 Gen 2x2 with two channels aggregated), 50 ps intra-pair skew, 8 ohm RON, 0.45 pF typical on-capacitance, sub-130 ns propagation delay, and dual supply support with 1.71 V to 1.98 V core and 3.0 V to 3.6 V I/O. The 42-pin WQFN (RUA) package provides a 31 C/W thermal pad-to-ambient resistance and supports -40 C to +105 C industrial operation. The architecture uses a pair of differential CMOS pass gates per channel with an integrated charge pump to maintain low RON across the full signal swing, plus on-chip termination resistors selectable through SEL pins. The bidirectional design means the same part handles both upstream and downstream switching, simplifying inventory and reducing PCB layout differences between mux and demux placements. Typical applications include USB Type-C port multiplexers, DisplayPort dual-mode source switching, PCIe lane failover, SATA port multipliers, and front-panel USB-C routing on motherboards, docking stations, and embedded computing platforms. The wide 3.0 V to 3.6 V supply range makes it compatible with both 3.3 V I/O rail and modern sub-1.8 V core supplies. When designing with the TMUXHS4412, route the high-speed differential pairs as 90 ohm differential impedance with length matching to within 5 mils, place decoupling capacitors within 2 mm of each supply pin, and solder the exposed thermal pad to a thermal land on a high-K board to maintain the full -40 C to +105 C temperature range without additional vias. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not consolidated in the manufacturer datasheet, including 8 ohm RON and 13 GHz bandwidth values verified from the TI TMUXHS4412 datasheet.
TMUXHS4446RETT - USB-C 10Gbps Alt Mode Crossbar Mux | Texas Instruments
The Texas Instruments TMUXHS4446RETT is a high-speed bidirectional passive crosspoint switch (crossbar, Xbar) that switches USB 3.2 Gen2 SuperSpeed and DisplayPort 1.4/2.1 (up to 10 Gbps UHBR10) signals over a USB Type-C interface, with 7-ohm typical on-resistance, a 6x4 mux configuration, and a 40-pin WQFN (6 mm x 3 mm) package with exposed pad. A crosspoint switch or crossbar mux is a switching matrix in which any input lane can be routed to any output lane, giving system designers complete flexibility in high-speed signal routing. In the USB Type-C ecosystem, crossbar switches sit between the SuperSpeed/sideband pins of the USB-C connector and a device's USB 3.2 or DisplayPort controller, resolving the orientation and alternate-mode ambiguity that the reversible Type-C connector introduces. As such, it belongs to the analog switch and multiplexer family within signal-switching ICs, sitting between the USB-C connector and the SoC in the system hierarchy. Key features include support for USB 3.2 Gen2 (10 Gbps) SuperSpeed lanes and DisplayPort 1.4/2.1 UHBR10 signaling, integrated low-speed SBU switching for DisplayPort auxiliary (AUX) channels, and a passive, bidirectional switch architecture that adds minimal signal degradation. The 7-ohm typical on-resistance minimizes insertion loss impact on high-speed differential pairs, helping preserve eye diagrams at 10 Gbps rates. Architecturally, the TMUXHS4446 is a passive FET-switch crossbar rather than an active redriver or retimer. This means it consumes minimal power, introduces no added latency, and does not regenerate the signal, so total channel budget must account for its on-resistance and capacitive loading. Passive switching makes it ideal when the host and device have adequate link budget and no equalization is required. Typical applications include USB Type-C docks and dongles that switch between USB 3.2 and DisplayPort alternate mode, notebooks and tablets routing DP 1.4/2.1 lanes to a USB-C port, monitors with USB-C inputs, and smartphone or mobile-compute platforms requiring USB-C orientation and alternate-mode switching. A key design consideration is that because the part is passive, total insertion loss across the connector, PCB traces, and switch must fit the USB 3.2 Gen2 or DP UHBR10 channel budget; keep routing short and impedance-controlled. Follow TI's datasheet layout guidance for the exposed-pad WQFN. This page synthesizes distributor pricing data, drop-in alternative analysis, and practical design notes that go beyond the manufacturer datasheet, giving engineers a single citable reference for the TMUXHS4446RETT.
TPS2371D - IEEE 802.3af PoE Power Interface Switch | TI
The Texas Instruments TPS2371D is an IEEE 802.3af-compatible power interface switch for Power over Ethernet powered devices, with an 8-pin SOIC package. It is designed for PoE powered-device front ends that require controlled power delivery from an Ethernet connection. The verified listing identifies the device as a specialized power interface switch with a nominal 48 V supply context, CMOS technology, eight terminals, and a 1.27 mm terminal pitch. A power interface switch is the input-side protection and power-management circuit between an Ethernet cable and a PoE powered device. Its role is to establish the power path, protect the downstream system from unsuitable input conditions, and support the current and voltage limits associated with legacy IEEE 802.3af PoE systems. In system terms, it belongs to the power-management IC hierarchy and the broader PoE interface ecosystem. The main verified characteristics are legacy IEEE 802.3af compatibility, operation in the PoE power domain, an 8-terminal surface-mount SOIC format, and a listed maximum operating temperature of 70 °C. The distributor record also identifies a 57 V-related comparison context, while the supplied Partstack result lists 48 V nominal voltage. These figures should be checked against the manufacturer datasheet before final design release because the search snippets do not provide the complete electrical characteristic table. Typical uses include PoE-powered IP cameras, network access points, VoIP phones, industrial Ethernet endpoints, and other powered devices connected through an Ethernet infrastructure. The device is appropriate when the design uses the legacy 802.3af power interface concept and the existing board uses the TPS2371D pin arrangement. It is not a generic USB power switch or a complete PoE PD controller; neighboring devices with similar package names may serve different voltage, current, or protection functions. For PCB implementation, place the switch close to the Ethernet input and power-entry components, maintain the datasheet-defined spacing for high-voltage copper, and provide the required input and output decoupling. Confirm absolute maximum ratings, operating voltage, current limit behavior, thermal conditions, and exposed-lead connections from the official TPS2371 documentation before applying it to a new design. This page consolidates verified distributor availability, manufacturer positioning, package information, procurement data, and design cautions for engineers evaluating TPS2371D replacements or PoE front-end implementations.
TPS2371DR - IEEE 802.3af PoE PD Interface | Texas Instruments
The Texas Instruments TPS2371DR is an IEEE 802.3af-compatible power interface switch for Power over Ethernet powered devices, with integrated hot-swap and power-distribution functions in an 8-pin SOIC package. It provides a PD detection signature, class 0-4 classification signature, precision undervoltage lockout, a 20-ms UVLO off-time delay, and programmable inrush-current limiting. A Power over Ethernet powered-device interface is the circuit that receives power through an Ethernet cable, identifies the attached load, negotiates its power class, and safely connects that power to the local system. In the power hierarchy, a PD interface sits between the PoE supply and the powered equipment’s DC/DC converter or load. It prevents an unsupported or improperly connected network port from receiving unsafe power. The TPS2371DR’s principal engineering benefits are its IEEE 802.3af compatibility, integrated protection, and autonomous interface operation. The device provides both detection and classification signatures, eliminating separate handshake circuitry in many conventional PoE PD designs. Its internal hot-swap MOSFET helps control connection transients, while the programmable inrush limit reduces the stress applied to downstream capacitance and power circuitry. The chip also uses precision UVLO thresholds to distinguish valid operating conditions and includes a defined 20-ms off-time delay after UVLO. That delay provides controlled recovery before the interface attempts another valid operating state. As an 8-SOIC surface-mount device, the TPS2371DR supports compact PoE endpoint designs without requiring a large connector-side or board-edge package. Typical uses include IP cameras, VoIP phones, wireless access points, network switches, powered network adapters, and other low- to moderate-power Ethernet endpoints. These products can use the TPS2371DR when IEEE 802.3af behavior and a conventional eight-pin PoE PD interface are required. For higher-power or newer PoE standards, designers should verify the exact PSE, PD, class, voltage, and protection requirements before selecting this legacy-compatible device. Layout should keep the Ethernet input and power-path nodes physically separated from sensitive downstream electronics, and it should provide appropriate copper area for thermal dissipation during sustained power transfer. Component values must follow the manufacturer’s reference design because the programmable inrush and protection network determine startup behavior. The interface also requires correct grounding and protection placement to avoid allowing transient current into sensitive ports. This page consolidates the verified manufacturer, distributor, pricing, lifecycle, and replacement information for TPS2371DR, while clearly separating confirmed specifications from unavailable electrical details. It also provides application guidance and drop-in alternatives where the available cross-reference evidence supports pin and package compatibility.
TPS66021YBGR - 20V Sink, 5V Source USB-C Switch | TI
The Texas Instruments TPS66021YBGR is a one-channel integrated USB-C Power Delivery source-and-sink power multiplexer with a 20V sink path, a 5V source path, and a 5V dead-battery VBUS LDO, housed in a 28-ball DSBGA package measuring 1.61 mm by 2.81 mm. It combines two directional power paths in a compact device intended to manage charging, powering, and protection around a USB-C connection. A USB-C power-path multiplexer is a specialized power-management integrated circuit that controls current between a connector and internal supply rails. It belongs to the hierarchy power multiplexer, power-path controller, power-management IC, and semiconductor. By combining source and sink switching, it can route external VBUS power into a system, provide regulated 5V power from an internal source, and isolate paths during faults or operating-mode changes. The verified manufacturer data identifies a 4V-to-22V sink power path and a 5V source path. The source path enters constant-current operation when its load exceeds the selected current-limit threshold. Each path includes overtemperature and reverse-current protection, while the family supports a fault indication for overcurrent and overtemperature events. The integrated high-voltage VBUS LDO provides 5V for this device and other system components under dead-battery conditions. The TPS66021 integrates a 20V USB-C sink capability and 5V source capability rather than acting only as a passive analog switch. Its VBUS-side architecture allows the system to distinguish and control external power conditions, while the source path supplies a defined output level. The fault function gives the host circuitry a signal when protection circuitry has detected an abnormal event, enabling controlled shutdown or fault recovery. Typical uses include USB-C laptop and tablet power adapters, portable equipment, battery-powered industrial products, and compact systems that must accept external USB-C power while retaining a safe internal 5V supply. The integrated source, sink, and dead-battery functions can reduce board area compared with a discrete switch network. Designers must still validate connector orientation, CC behavior, capacitor selection, current limits, thermal performance, and system power sequencing against the full manufacturer documentation. For PCB layout, follow the manufacturer package land pattern and place high-current input, output, and ground connections with short, wide paths. Place required input and output capacitors close to their associated balls and keep sensitive control and fault traces away from high-di/dt power loops. Verify the selected current threshold, startup behavior, and fault response in the final USB-C system. This page consolidates verified manufacturer descriptions, distributor availability, package information, replacement evidence, and application guidance. It also distinguishes confirmed facts from parameters that require the complete datasheet, preventing unsupported electrical or compliance assumptions during design review.
TPS8802DCPR - Smoke Alarm AFE with CO Support | TI
The Texas Instruments TPS8802DCPR is a smoke-alarm analog front end (AFE) for residential smoke detectors, integrating the regulators, amplifiers, and drivers required for a dual-wave photoelectric smoke alarm and carbon monoxide detection system. The verified distributor listing identifies a 38-pin HTSSOP package and analog input with I2C output. TI describes the device as a high-performance, multi-channel, digital-input solution whose flexible architecture suits smoke-alarm systems where precision and power consumption are critical. What is a smoke-alarm analog front end? An AFE is a semiconductor that connects physical sensing elements to an embedded system. In a photoelectric alarm, light scattering and light-absorption signals require controlled excitation, amplification, filtering, and diagnosis. The TPS8802DCPR integrates those signal-chain functions together with supporting regulators and drivers, reducing the number of discrete components and helping designers create a compact, low-power detector platform. The verified TI product information highlights a wide input-voltage range, low standby-power consumption, and power-saving features designed to support 10-year battery-powered smoke-alarm systems. Its dual-wave photoelectric architecture and CO-detection capability allow one integrated platform to combine optical smoke sensing with electrochemical CO-sensor signal conditioning. The I2C interface provides a digital control and diagnostic path, while the analog input supports direct connection to sensing circuitry. The TPS8802DCPR is intended for residential smoke alarms, combination smoke-and-CO alarms, and other safety products requiring highly integrated sensing support. Its integrated regulators and amplifiers can simplify power-tree design compared with a discrete implementation, while digital configuration can support manufacturing tests and field diagnostics. Exact electrical limits, gain settings, timing values, and pin functions were not included in the supplied verified records and therefore require confirmation from the manufacturer datasheet before design release. For battery operation, standby current is especially important because the target application is a long-lived safety device. Designers should calculate average and peak current across the sensing duty cycle, confirm regulator startup behavior, and verify that low-power modes preserve alarm thresholds and diagnostic performance. The I2C pull-up arrangement, grounding, and decoupling should follow the manufacturer layout guidance to prevent communication errors or unintended current consumption. This product page consolidates the verified distributor classification, manufacturer application description, package information, source links, and design cautions. It does not invent electrical parameters or claim unverified drop-in equivalents. Confirm the complete pinout, absolute maximum ratings, recommended operating conditions, and lifecycle status in the current Texas Instruments documentation before schematic capture or PCB release.
TRS3221EIDBR - 3-5.5V RS-232 Transceiver, ±15kV ESD | Texas Instruments
The Texas Instruments TRS3221EIDBR is a 3-V to 5.5-V single-channel RS-232 line driver/receiver with ±15-kV IEC-ESD protection, packaged in a 16-pin SSOP (DB). It operates from a single supply rail and integrates a charge-pump that generates the ±RS-232 voltage swing from the input supply, so no external ±12 V rails are required. The device supports data rates up to 250 kbps and is rated for ±15-kV HBM, ±8-kV IEC 61000-4-2 contact, and ±15-kV IEC 61000-4-2 air-gap ESD strikes on the RS-232 bus pins. An RS-232 transceiver is a type of line driver/receiver IC that converts logic-level (typically 0/3.3 V or 0/5 V CMOS/CMOS) UART signals into the ±5 V to ±15 V voltage swings required by the TIA/EIA-232-F and ITU v.28 standards. It belongs to the broader interface-IC category, sitting between the UART block of a microcontroller/SoC and a DB-9 (or equivalent) connector on the serial port. Single-channel variants like the TRS3221E serve compact, point-to-point designs where two driver/receiver channels are not needed, helping shrink BOM cost and PCB area versus 2-channel parts. Key features include 1 driver and 1 receiver per channel, a dedicated enable input for power management, an auto-powerdown mode that drops quiescent current to 1 µA typical when the cable is disconnected, and an always-active supplementary receiver that monitors the ring-indicator path even in shutdown. The device meets or exceeds the TIA/EIA-232-F and ITU v.28 electrical specifications, and is offered in industrial temperature grades of -40 °C to +85 °C. A high-speed pin-compatible upgrade, the TRSF3221E, is available where 1 Mbit/s operation is required. The TRS3221E uses an on-chip switched-capacitor voltage converter with four external 0.1 µF charge-pump capacitors. The architecture tolerates supply rails as low as 3.0 V while still generating compliant ±5 V (minimum) RS-232 output swings, which is the headline advantage over legacy 5-V-only RS-232 transceivers. Drivers are slew-rate limited to keep EMI low, and the receivers include hysteresis to reject noise on long cables. Typical applications include industrial single-port serial ports, point-of-sale terminals, handheld data collectors, factory automation equipment, medical instruments with DB-9 serial interfaces, and any embedded system that needs a robust RS-232 link from a 3.3 V or 5 V UART. Designers often pair this part with a TVS array for additional surge protection when the cable is exposed to outdoor or industrial transients. When designing with the TRS3221EIDBR, place the four charge-pump capacitors (typically 0.1 µF X7R) as close as possible to the C0+, C0-, C1+, C1- pins to minimize supply ripple. Decouple VCC with a 0.1 µF + 1 µF combination near the pin, and respect the absolute-maximum ratings on the RS-232 outputs (typically ±13.2 V) by avoiding back-drive when the IC is unpowered. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TRS3221EIRGTR - 3-5.5V RS-232 Transceiver, 250kbps, ±15kV ESD | Texas Instruments
The Texas Instruments TRS3221EIRGTR is a 3- to 5.5-V single-channel RS-232 line driver/receiver delivering 250 kbps data rate with ±15 kV IEC-ESD protection in a 16-pin VQFN (RGT) package measuring 3x3 mm with an exposed thermal pad. The device integrates one driver and one receiver, supports VCC operation from 3.0 V to 5.5 V (compatible with TTL/CMOS logic levels), and meets or exceeds the requirements of TIA/EIA-232-F and ITU v.28 standards. An RS-232 transceiver is a charge-pump-based interface IC that translates between TTL/CMOS logic levels (0-3.3 V or 0-5 V) and the ±5 V to ±15 V swing required by the legacy TIA/EIA-232-F serial communication standard. RS-232 transceivers belong to the broader interface IC family, which sits hierarchically between discrete level-shifters and protocol controllers (UARTs) in wired communication systems. RS-232 remains widely deployed in industrial equipment, point-of-sale terminals, medical instruments, and embedded debug ports where simplicity, point-to-point connectivity, and proven robustness outweigh the bandwidth advantages of USB or Ethernet. Key features include ±15 kV Human-Body Model (HBM) ESD protection on RS-232 pins, ±8 kV IEC 61000-4-2 contact discharge, ±15 kV IEC 61000-4-2 air-gap discharge, and an automatic powerdown feature that disables drivers when no valid RS-232 cable is detected. The on-chip dual charge pump requires only four external 0.1 µF capacitors, enabling true 5 V operation from a single 3.3 V supply without a separate ±12 V rail. The 250 kbps data rate is adequate for all standard RS-232 baud rates up to and beyond 115200 with margin to spare. The architecture combines a regulated switched-capacitor voltage doubler/inverter with a proprietary low-dropout RS-232 driver stage and a precision hysteresis receiver. ESD protection is implemented at the cable-side pins using TI's integrated silicon-controlled-rectifier (SCR) clamps. The 16-pin VQFN package's exposed pad provides a low thermal resistance path, which is useful when the part operates near the upper end of its 1 mA quiescent current budget in warm enclosures. Typical applications include industrial PLC programming ports, point-of-sale (POS) terminals, medical device serial consoles, battery-powered handhelds, and embedded debug UARTs that need robust ESD performance in the field. The TRS3221EIRGTR's small 3x3 mm footprint suits space-constrained designs such as USB-to-serial dongles, IoT gateways, and barcode scanners. When designing with this part, place the four charge-pump capacitors as close as possible to the C1+ / C1- / C2+ / C2- pins and keep the RS-232 trace lengths short to maximize ESD margin. Note that the TRSF3221E is the higher-speed (1 Mbit/s) pin-compatible alternative if 250 kbps is insufficient. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TRSF3222CPW - 3V-5.5V RS-232 Transceiver, 2/2 Drivers | TI TSSOP-20
The Texas Instruments TRSF3222CPW is a 2-driver/2-receiver RS-232 line transceiver that operates from a single 3.0V to 5.5V supply in a 20-pin TSSOP package. It supports data rates up to 1 Mbit/s and accepts 5-V logic inputs when powered from a 3.3V rail, making it ideal for mixed-voltage system designs. A line transceiver is an interface device that bridges a logic-level UART (universal asynchronous receiver/transmitter) on a host microcontroller with the RS-232 standard, which swings between +12V and -12V on the bus side. It sits within the Interface IC hierarchy (RS-232 transceiver -> line transceiver -> interface IC -> integrated circuit) and converts TTL/CMOS logic levels to TIA/EIA-232-F compliant voltage levels while protecting the host from ESD events on the cable side. The TRSF3222CPW integrates a dual charge-pump that generates the required +5.5V and -5.5V rails from a single 3.3V supply using four small 0.1 uF external capacitors. Standby current is typically 1 uA, supporting low-power portable designs. The receivers remain active in shutdown, allowing wake-up characters to be detected without waking the host. ESD protection exceeds +/-15 kV HBM on the bus pins. Typical applications include industrial point-of-sale terminals, factory automation equipment, portable diagnostic instruments, and battery-powered barcode scanners where 3.3V logic must communicate with legacy RS-232 peripherals. The wide 3.0V-5.5V supply range also makes the part suitable for USB-to-serial bridges and embedded computing modules. When designing with this device, place the four charge-pump capacitors as close to the IC as possible to minimize loop inductance. The TSSOP-20 footprint requires standard surface-mount assembly with a maximum reflow temperature per JEDEC J-STD-020. Decouple VCC with a 0.1 uF ceramic plus a bulk tantalum if the supply impedance is high.
TS3A27518ERTWR - 6-Ch 2:1 Analog Mux, 240MHz | Texas Instruments
The Texas Instruments TS3A27518ERTWR is a bidirectional 6-channel 1:2 (SPDT) analog multiplexer/demultiplexer with 6.2 ohm on-resistance, 240 MHz bandwidth, and integrated IEC 61000-4-2 ESD protection, housed in a 24-pin WQFN (4x4 mm) package operating from a 1.65 V to 3.6 V single supply. An analog multiplexer is a signal-routing semiconductor that selects one of several input channels and connects it to a common output, functioning as a digitally controlled switch for both analog and digital signals. Within the signal-chain hierarchy, it sits between passive switches and full crosspoint matrices, and belongs to the broader family of interface and analog switch ICs used in power management and signal conditioning subsystems. Key features include low 6.2 ohm typical on-resistance for minimal signal attenuation, 21.5 pF typical switch capacitance, up to 240 MHz bandwidth for high-speed rail-to-rail signal handling, and -62 dB crosstalk and OFF isolation. The device also provides isolation in power-down mode (VCC = 0 V), and 1.8 V logic-threshold-compatible control inputs that allow direct interfacing with low-voltage microcontrollers. Architecturally, the TS3A27518E uses two control pins, each simultaneously controlling three 1:2 multiplexer sections, plus an enable pin that places all outputs in high-impedance mode. Integrated ESD cells rated to IEC 61000-4-2 on the signal pins eliminate the need for external TVS diodes in USB and port-protection designs, and the device is qualified for automotive applications. Typical applications include USB 2.0 high-speed signal switching, audio jack and headset detection, battery-powered portable equipment, and general-purpose analog signal routing in industrial systems. A key design consideration is on-resistance flatness across the signal range: at lower VCC the Ron rises, so budget for insertion loss at 1.65 V operation, and keep stub lengths short to preserve the 240 MHz bandwidth. This page adds value beyond the datasheet by synthesizing distributor pricing tiers, drop-in alternatives, cross-reference data, and practical design notes in one reference.
TS3A44159RGTR - 0.45Ω Quad SPDT Analog Switch | TI
The Texas Instruments TS3A44159RGTR is a 0.45-Ω quad-channel single-pole double-throw (SPDT) analog switch housed in a 16-pin VQFN (RGT) 3x3 mm package. Operating from 1.65 V to 4.3 V, it delivers low on-state resistance with excellent Ron matching across four independent 2:1 multiplexers and supports bidirectional signal flow on every channel. Two logic-level control inputs select between the NO/NC paths of all four switches simultaneously, simplifying firmware-driven signal routing. An analog switch is a solid-state semiconductor device that routes analog or digital signals between two or more terminals under the control of a logic-level signal. It belongs to the analog switch and multiplexer family, which sits inside the broader interface IC category of integrated circuits. Quad SPDT switches are commonly used to swap between two sources on four channels at once, an arrangement also called a 2-channel DPDT function in this device. Key features include 0.45 Ω typical on-state resistance, 50 pA typical switch leakage, break-before-make switching to prevent momentary channel cross-connection, and a -3 dB bandwidth greater than 35 MHz. The control inputs are 1.8 V logic-compatible, while supply operation extends from 1.65 V to 4.3 V. ESD protection on the switch pins exceeds 2000 V per the HBM model. Architecturally the part uses CMOS transmission gates with integrated charge-pump-derived well biasing, enabling low Ron and rail-to-rail signal swing on a single positive supply. Ron flatness is held tight across the input common-mode range, which preserves harmonic distortion performance in audio paths. The device draws only microamps of quiescent current, which is essential for battery-powered systems. Typical applications include portable audio routing between headphone jack and Bluetooth receiver, USB 2.0 high-speed signal switching, SPI/I²C bus multiplexing, smartphone audio codec path selection, and PDA or portable media player source switching. Industrial uses include 4-wire resistance measurement multiplexing and analog front-end signal routing. When designing with this part, ensure that the logic-high level on IN1/IN2 exceeds 0.85 x VDD and the logic-low is below 0.15 x VDD to guarantee full CMOS-level switching. Place 0.1 µF bypass capacitors within 5 mm of the VDD pin to keep digital control noise out of the analog path. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical PCB layout guidance not found in the manufacturer datasheet alone.
TS3A4741DCNR - 0.9Ω Dual SPST Analog Switch | TI SOT-23-8
The Texas Instruments TS3A4741DCNR is a 0.9 Ω low on-resistance, low-voltage, single-supply, dual single-pole single-throw (SPST) analog switch housed in an 8-pin SOT-23 (DCN) package. It integrates two independent normally open (NO) switches, each with a 1:1 (SPST) topology, designed for 1.8 V logic compatibility when operated from a single 3 V supply rail. What is an SPST analog switch? An SPST (Single-Pole Single-Throw) analog switch is a solid-state semiconductor device that routes analog signals by electrically connecting or isolating one signal path. The TS3A4741 belongs to the broader category of analog switches and multiplexers, a subfamily of interface ICs used for signal routing in mixed-signal and low-power systems. Compared with mechanical relays, analog switches offer far faster switching speeds, lower power, smaller PCB area, and no mechanical bounce, at the cost of lower absolute voltage and current handling. Key specifications include a 0.9 Ω typical on-resistance (Ron), 1.8 V CMOS-compatible digital logic inputs, rail-to-rail analog signal handling, very low quiescent current, and integrated ESD protection. The two switches operate completely independently, allowing them to be used as separate signal paths or as complementary paths in a single function. The device is fabricated in a CMOS process and supports fast switching speeds, low off-leakage current, and bidirectional analog signal flow. Its small SOT-23-8 footprint and 1.8 V logic compatibility make it well suited to portable and battery-powered designs. Typical applications include audio signal routing in portable devices, switching between two sensors in handheld instruments, power rail multiplexing in low-power systems, and general-purpose signal gating in test equipment and consumer electronics. When designing with the TS3A4741, ensure the analog signal stays within the supply rails to avoid distortion or excessive leakage, and add 0.1 µF decoupling close to VCC. For applications requiring normally closed (NC) switches, use the pin-compatible TS3A4742. This page synthesizes verified distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TS3A4751PWR - 0.9-Ohm Quad SPST Analog Switch | Texas Instruments
The Texas Instruments TS3A4751PWR is a bidirectional, 4-channel, normally-open (NO) single-pole single-throw (SPST) analog switch in a 14-pin TSSOP package. It operates from a single 1.6V to 3.6V supply, delivers a maximum on-state resistance of 0.9 ohm at a 3V supply, and handles rail-to-rail analog signals with fast switching speeds and very low quiescent power. An analog switch is an IC that routes or isolates analog signal paths under digital control. Within the signal-routing hierarchy, the TS3A4751 belongs to the SPST switch family, a subset of analog switches and multiplexers used in signal conditioning and power-management systems. Key features include 0.9-ohm maximum Ron at 3V (1.5-ohm maximum at 1.8V), Ron flatness of 0.4-ohm maximum at 3V, and Ron matching of 0.05-ohm maximum at 3V. The 1.8-V CMOS-compatible digital inputs allow direct interface with low-voltage GPIO when using a 3-V supply, eliminating level-shift circuitry. The device is available in 14-pin TSSOP (PW), 14-pin VQFN (RGY), and 2x2-mm micro X2QFN (RUC) packages. The low Ron supports power-switching and low-distortion signal paths, while rail-to-rail operation preserves full signal swing on 1.8V, 2.5V, and 3.3V rails. Typical applications include low-voltage power switching, audio signal routing in portable devices, battery-powered test points, and general-purpose signal muxing in smartphones, tablets, and industrial sensing modules. Its normally-open configuration makes it suitable for fail-safe, default-disconnected paths. When designing, remember that Ron rises at lower supply voltages: at a 1.8-V supply the maximum Ron is 1.5 ohm, so account for insertion loss and on-resistance flatness in high-fidelity or precision-current paths. According to TI datasheet, the TS3A4751 is the NO-switch counterpart within the TI low-voltage quad SPST family.
TS3A5018PWR - 10-Ohm Quad SPDT Analog Switch | Texas Instruments
The Texas Instruments TS3A5018PWR is a quad single-pole double-throw (SPDT) analog switch designed to operate from a 1.8V to 3.6V supply in a 16-pin TSSOP (PW) package rated from -40C to +85C. It handles both digital and analog signals, and signals up to V+ can be transmitted in either direction. An analog switch is a semiconductor device that selectively connects or disconnects an analog signal path under digital control. It is a fundamental signal-routing building block in the broader family of multiplexers, demultiplexers, and interface ICs. Analog switches provide a low-resistance path when ON and a high-impedance path when OFF, replacing bulky mechanical relays in audio/video routing, data acquisition, and communication systems. Key features include the wide 1.8V to 3.6V operating range (ideal for battery-powered and 3.3V systems), low 10-ohm ON-state resistance with excellent channel-to-channel matching, and low charge injection that minimizes glitches during switch transitions. All four SPDT switches share a common enable function so the entire device can be disabled to reduce power consumption. The TS3A5018 is built on TI CMOS process technology, providing low quiescent power dissipation and high reliability. Bidirectional signal flow means either of the two throw terminals can serve as the port, essential for multiplexing and demultiplexing on the same hardware. Turn-on and turn-off times are fast, supporting high-speed signal routing in data converters and communication interfaces. Typical applications include audio signal routing in portable devices, battery-powered data acquisition front ends, communication interface switching, and test equipment signal multiplexing. The low power consumption and wide supply range make it well suited for portable and industrial designs. Design consideration: the 10-ohm ON resistance introduces series attenuation in high-impedance circuits, so prefer low-impedance loads or buffer the switched node. Place a 0.1uF decoupling capacitor close to the V+ pin, and use the enable pin in battery designs to cut standby current when switching is idle.
TS3USB3000MRSER - DPDT USB 2.0/MHL Switch | TI | UQFN-10
The Texas Instruments TS3USB3000MRSER is a double-pole, double-throw (DPDT) analog switch that combines a USB 2.0 High-Speed (480 Mbps) switch and a Mobile High-Definition Link (MHL) switch in a single 10-pin UQFN (RSE) package measuring 1.5 mm × 2.0 mm. It supports a -3 dB bandwidth of 6.1 GHz on the MHL path and operates from a 2.3 V to 4.8 V supply. The device is designed to share a common USB or Micro-USB connector between USB 2.0 data and MHL video signals in mobile phones, tablets, and portable media devices. A USB switch IC is a special-purpose analog multiplexer that routes high-speed differential signals between a single downstream port and two upstream paths (host vs. MHL sink). In the hierarchy of power management and signal routing components, this part belongs to the USB interface IC category, sitting between the connector and the application processor. DPDT switches such as the TS3USB3000 are critical because they must pass 480 Mbps USB signals and up to 3 GHz MHL content with minimal insertion loss, low crosstalk, and high off-isolation. Key features of the TS3USB3000 include low on-resistance (Ron) on the USB data paths, low on-capacitance (Con) for high-bandwidth signal transmission, 1.8-V-compatible select pins for direct GPIO control from a mobile processor, and a quiescent current of approximately 5 uA. The wide supply range (2.3 V to 4.8 V) covers both 3.3 V system rails and the typical 3.8 V Li-ion battery range without additional regulation. The small 1.5 mm × 2 mm UQFN footprint makes it ideal for space-constrained mobile applications. The TS3USB3000 uses a charge-pump-less architecture with simple CMOS logic-level select inputs. The two select pins (S1 and S0 per TI documentation) determine whether the common port is routed to the USB path or the MHL path. Internal ESD protection on the signal pins improves robustness against connector-level transients, which is critical for hot-plug consumer electronics. Typical applications include smartphones and tablets with MHL-enabled video output, automotive infotainment systems that mirror mobile content via USB or MHL, portable media players, and USB/MHL dongles. The wide bandwidth also makes it suitable for any system needing to multiplex two high-speed differential pairs onto a single connector. When designing with this part, place the device as close as possible to the USB/MHL connector to minimize stub lengths and signal-integrity degradation. Use controlled-impedance differential routing (90 ohm) on both sides of the switch, and provide adequate ground stitching vias along the signal path to maintain return-current continuity. This page synthesizes distributor pricing, pin-compatible alternatives, and practical design notes that are not aggregated in any single manufacturer datasheet or distributor catalog page.
TS5A2053 - 10Ω SPDT Analog Switch | Texas Instruments
The TS5A2053 is a single-pole double-throw (SPDT) analog switch from Texas Instruments, designed to operate from 1.65 V to 5.5 V. It can handle both digital and analog signals, and signals up to V+ can be transmitted in either direction. The device features a low ON-state resistance of 10Ω (typical) and includes an enable pin for power management. It is available in the 8-pin VSSOP (DCU) package, making it suitable for space-constrained applications. An analog switch is a semiconductor device that selectively connects or disconnects an analog signal path based on a digital control signal. It is a fundamental building block in signal routing, multiplexing, and sample-and-hold circuits. Analog switches are part of the broader category of interface ICs, which manage signal integrity and connectivity between different subsystems in electronic systems. Key features of the TS5A2053 include a low ON-state resistance of 10Ω, which minimizes signal attenuation, and a wide operating voltage range from 1.65 V to 5.5 V, allowing compatibility with various logic levels. The device also offers fast switching speeds, with a typical turn-on time of 20 ns and turn-off time of 15 ns, making it suitable for high-frequency signal routing. The enable pin allows the switch to be disabled, reducing power consumption in standby modes. Technically, the TS5A2053 uses a CMOS process that provides low power consumption and high ESD robustness. The device has a bandwidth of 300 MHz, enabling it to pass high-frequency signals with minimal distortion. The ON-state resistance is flat across the input voltage range, ensuring consistent performance. The device also features break-before-make switching, preventing momentary short circuits between channels. Typical applications include audio signal routing, data acquisition systems, and test equipment. In audio systems, the low ON-state resistance and high bandwidth ensure minimal signal degradation. In data acquisition, the switch can route analog signals to an ADC, with the enable pin allowing power saving when not in use. In test equipment, the TS5A2053 can be used for signal multiplexing and routing. When designing with the TS5A2053, it is important to consider the ON-state resistance and its effect on signal integrity. For high-frequency signals, the parasitic capacitance of the switch can cause signal attenuation, so proper PCB layout and termination are recommended. Additionally, the enable pin should be tied to a defined logic level to avoid floating inputs.
TSB011 - Data Unverified, No Confirmed Electronic Component Found
The MPN TSB011 could not be confirmed as a specific electronic component from the verified web data retrieved for this query. Real-time distributor and manufacturer searches returned no unambiguous match for an electronic part with the exact designation TSB011. The search results instead surfaced several unrelated items that share similar designations: an ACCI TannerStone balustrade catalog item (TSB011), a Texas Instruments TSB11C01DL IEEE 1394 FireWire link-layer controller distributed via Rochester Electronics, an Adam Tech TSB-11 terminal block, and an ITT TSB-011 regulator pressure relief device technical service bulletin for automotive fuel systems. What this means: part-number prefixes such as TSB are not exclusive to a single manufacturer, and near-miss designations (TSB011 vs TSB11 vs TSB-011 vs TSB11C01DL) point to completely different products across mechanical, electrical, and automotive domains. Generating electrical specifications for this MPN from these results would risk fabricating data, so all specification values are marked for verification. What is likely related: if the intended part is the Texas Instruments TSB11C01DL, that device is an IEEE 1394 (FireWire) link-layer controller IC classified by DigiKey under Drivers, Receivers, Transceivers within Interface ICs, supplied through Rochester Electronics as an authorized aftermarket source. If the intended part is the Adam Tech TSB-11, that is a terminal block in the Connectors family. Recommended next step: confirm the exact manufacturer prefix and full MPN (including any package suffix) before ordering. This page will be updated once verified datasheet data is available.
TSI384-133ILV - PCIe to PCI-X Bridge 256-BGA | Renesas Electronics
The Renesas TSI384-133ILV is a single-lane PCI Express (PCIe) to PCI/PCI-X bridge IC housed in a 256-ball PBGA (17x17 mm) package. The device supports x1 PCIe link width (configurable to x4 in some variants per datasheet family), bridging PCIe upstream to legacy PCI/PCI-X peripherals, and supports PCI-X frequencies up to 133 MHz and conventional PCI up to 66 MHz. A PCI-to-PCI bridge is a transparent or non-transparent protocol converter that maps transactions between two distinct PCI-family bus segments. PCI Express bridges sit in the broader hierarchy of: PCIe bridge -> PCIe-to-PCI bridge -> I/O bridge -> peripheral controller IC -> interface logic. Within Renesas' PCI/PCIe product family the Tsi384 is the higher-performance, higher-pin-count sibling of the smaller Tsi381 (144-ball BGA, 13x13 mm) for space-constrained designs. Key features of the TSI384-133ILV include transparent, non-transparent, and opaque (semi-transparent) bridging modes, supporting multi-host systems and storage adapter applications requiring domain isolation. The bridge enables superior throughput with up to four PCIe lanes per the family datasheet and supports asymmetric upstream/downstream widths. Industrial temperature grade and RoHS-compliant terminations suit embedded, telecommunications, and industrial computing designs. Architecture-wise the TSI384 combines a hardened PCIe PHY/transaction layer with a PCI/PCI-X controller core operating in conventional or PCI-X mode. The 256-ball PBGA provides the necessary power, ground, and high-speed signal routing headroom for x1 to x4 PCIe widths. Operating supply voltage is 1.2 V core plus I/O rails, supplied via multiple pins. Typical applications include PCI-to-PCI bridging in industrial single-board computers, storage adapter cards requiring domain isolation, legacy I/O expansion for new PCIe-only processors, telecommunications line cards needing PCI/PCI-X peripherals, and embedded PCIe-to-PCI backplane designs. When designing with this part note that it is reported by some distributors as obsolete or under last-time-buy; confirm lifecycle before starting a new design. Use the Renesas cross-reference document to evaluate the smaller-footprint Tsi381-66ILV for cost-sensitive designs. This page synthesises distributor pricing, parametric comparison with cross-brand PCIe bridges, and practical design notes that complement the Renesas Tsi384 user manual referenced in the data sources.
TUSB2040N - 4-Port USB 1.0 Hub Controller | Texas Instruments
Texas Instruments TUSB2040N is a four-port USB 1.0-compatible hub controller with integrated USB transceivers, per-port power switching, and overcurrent reporting. The device supports four downstream ports and two power-source arrangements: self-powered mode and bus-powered mode. It is packaged as a 28-pin PDIP according to the retrieved distributor records. The verified source identifies the TUSB2040 family as a universal serial bus hub controller and does not provide additional electrical timing, current, or temperature values. A USB hub controller is an interface IC that connects one upstream USB port to multiple downstream ports, allowing peripherals to share a host controller. Within the hierarchy of USB interface devices, transceiver, hub controller, interface IC, and semiconductor, the TUSB2040N provides the logic and physical connectivity for expanding USB 1.0 equipment. Its integrated transceivers reduce the need for separate USB transceiver circuitry on the hub board. The principal verified features are four downstream ports, integrated USB transceivers, USB 1.0 compliance, self-powered operation, bus-powered operation, per-port power switching, overcurrent reporting, per-port or ganged power modes, and suspend support. These functions suit hubs where the host must enumerate multiple peripherals and where each downstream port needs controllable power. The retrieved distributor listing describes the part as an interface controller, while the family datasheet result specifically identifies four-port USB hub functionality. The TUSB2040N is intended for USB 1.0 hub designs, including peripheral expansion, legacy computer interfaces, industrial equipment, and embedded systems that use multiple low-speed, full-speed, or compatible USB devices. Its architecture places port power management close to the USB interface, allowing the design to report overcurrent conditions and manage downstream power distribution. Exact propagation delays, operating voltage, maximum downstream current, and USB data-rate details are not present in the verified web data and must be confirmed from the manufacturer datasheet before a new design is released. For implementation, follow the TUSB2040 family datasheet for pin assignments, transceiver connections, power-source selection, capacitor values, and port-power topology. Pay particular attention to upstream and downstream USB differential routing, ground-plane continuity, and current-limit behavior. Because the verified record lists a PDIP package, verify physical dimensions and pin orientation against the actual manufacturer drawing rather than relying only on distributor metadata. This page combines the verified distributor and datasheet-search records with clearly marked missing-data fields. It does not infer prices, lifecycle claims, pin names, or electrical limits that were not supplied. Buyers should request a quotation for current commercial availability and confirm the exact package, ordering suffix, and production status with Texas Instruments before committing a design to production.
TUSB2046BVFR - 4-Port USB 2.0 Full-Speed Hub | TI
The Texas Instruments TUSB2046BVFR is a 4-port USB 2.0 full-speed (12 Mbps) hub controller with one upstream port and four downstream ports, implemented as a pure state-machine (no CPU core) in a 32-pin LQFP (VF, 7x7 mm) package. It operates from a single 3.0 V to 3.6 V supply, drawing approximately 40 mA, over a 0 C to 70 C commercial temperature range. A USB hub controller is a dedicated interface IC that expands a single USB upstream connection into multiple downstream ports, handling enumeration, transaction translation at the protocol level, and per-port power management. Within the system hierarchy it sits in the connectivity layer: interface IC > USB controller > hub controller, alongside host controllers and device controllers in a complete USB subsystem. Key features include full compliance with the USB specification as a full-speed hub (TI design TID #30220231), integrated USB transceivers that eliminate external PHY components, and an optional serial EEPROM interface for storing customized VID/PID and configuration data. Support for Win95/DOS-style operation and a pure hardware state-machine architecture reduce firmware complexity to zero - the hub enumerates automatically on plug-in. The TUSB2046B is fabricated on a low-power 3.3 V ASIC CMOS process. Because there is no embedded microcontroller, no firmware development, flash programming, or in-circuit emulator is required, which shortens qualification cycles and removes a whole class of field-update failure modes. The device supports individual downstream port power switching and overcurrent status inputs for compliant bus-powered and self-powered hub designs. Typical applications include standalone USB hubs, monitor and keyboard-display hubs, industrial and medical equipment USB expansion, and adding USB ports to embedded systems built around host processors without native hub capability. For design, provide 0.1 uF decoupling at each supply pin, strap configuration pins (or fit the optional EEPROM) for power-mode selection, and size port power switches per downstream port load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TUSB2046BVFRG4 - 4-Port USB 2.0 Full-Speed Hub | Texas Instruments
The Texas Instruments TUSB2046BVFRG4 is a 4-port USB 2.0 full-speed hub controller operating at 12 Mbps from a 3.3 V supply, housed in a 32-pin LQFP (7x7 mm) package with an optional serial EEPROM interface and a 0C to +70C commercial operating range. A USB hub controller is an interface IC that expands a single upstream USB port into multiple downstream ports, handling enumeration, transaction translation at the protocol level, and port power management. It sits within the USB device hierarchy between the host controller and downstream peripherals, forming a sub-family of the broader USB interface and connectivity IC class within semiconductor interface products. Key features include one upstream port and four downstream ports compliant with the USB 2.0 specification at full speed (12 Mbps), support for both low-speed (1.5 Mbps) and full-speed downstream devices, an optional serial EEPROM interface for storing vendor ID / product ID configuration data, and overcurrent detection inputs with power-switch control outputs for per-port or ganged power switching. Implementation with a digital state machine instead of an embedded microcontroller eliminates firmware development and reduces BOM complexity. Technical depth: because the TUSB2046B is a pure hardware state-machine design, enumeration latency is deterministic and there is no firmware to qualify, update, or corrupt. The 3.3 V CMOS core with integrated 3.3 V regulator support keeps external components minimal, typically requiring only a 6 MHz or 48 MHz clock source, bypass capacitors, and the external power switches for downstream VBUS. Typical applications include PC monitor hubs, docking stations, industrial panel USB expansion, printer and multifunction peripheral front panels, and embedded systems requiring additional USB ports from a single host connection. The 12 Mbps full-speed rating suits HID devices, flash drives, and instrumentation rather than high-bandwidth video or mass-storage arrays. Design consideration: budget downstream VBUS power carefully - each downstream port may supply up to 500 mA at 5 V per the USB specification, so external power MOSFET switches and overcurrent sensing resistors must be sized for the aggregate load, and the OVERCURRENT inputs must be wired to the correct power-switch pins. This page synthesizes distributor pricing context, drop-in alternatives, lifecycle status, and practical design notes not found in the manufacturer datasheet alone.