EPC2TC32UCF48 vs EPC2TC32U Comparaison
Comparaison détaillée côte à côte de EPC2TC32UCF48 par Intel et EPC2TC32U par Altera. Comparez les spécifications clés, les paramètres électriques, le conditionnement, le statut de cycle de vie, les prix et la disponibilité pour déterminer le meilleur composant pour vos exigences de conception.
Comparaison des spécifications
| Paramètre | EPC2TC32UCF48 | EPC2TC32U |
|---|---|---|
| Marque | Intel | Altera |
| Catégorie | Memory ICs | FPGA & CPLD |
| Statut du cycle de vie | NRND | NRND |
| Statut du stock | In Stock | In Stock |
| Prix unitaire (USD) | $10,85 | $5,85 |
| Type de mémoire | Non-volatile configuration PROM (CMOS Flash-based) | — |
| Memory Density | 1.6 Mbit (1.6 Mb / 32 Mbit raw) | — |
| Memory Configuration | Serial configuration bitstream storage | — |
| Supply Voltage (VCC) | 3.0 V to 3.6 V (3.3 V typical) | — |
| Supply Voltage (VCCIO) | 1.8 V / 2.5 V / 3.3 V (bank-level) | — |
| Output Drive Current (VCCIO) | [DATA_NEEDED: IOH/IOL at 3.3 V VCCIO] | — |
| Programming Interface | IEEE Std. 1149.1 JTAG (in-system programmable) | — |
| Configuration Interface | Altera serial PROM interface (DCLK, DATA, nCONFIG, nSTATUS, CONF_DONE) | Altera Passive Serial (DCLK / DATA0 / nCONFIG / nSTATUS / CONF_DONE) |
| Supported Configuration Modes | FPP, AS, PS, JTAG (mode dependent on target FPGA MSEL pins) | — |
| Daisy Chain Support | Yes (multi-device cascade for >16 Mbit FPGAs) | — |
| Maximum Cascaded Capacity | Up to 16 Mbit total across chain | — |
| Température de fonctionnement | 0C to +70C (commercial) | -40 C to +85 C |
| Boîtier | 48-pin TQFP (7x7 mm) | 32-pin QFP (CAF48, lead-free) |
| Type de montage | Surface Mount | Surface Mount |
| Niveau MSL | [DATA_NEEDED: MSL rating] | [DATA_NEEDED: MSL level] |
| Statut RoHS | [DATA_NEEDED: confirm RoHS compliance] | Compliant (lead-free / RoHS per distributor data) |
| Lead Free | [DATA_NEEDED: confirm lead-free] | — |
| Fonction | — | Serial Configuration Device for SRAM-based LUT FPGAs |
| Taille de mémoire | — | 1.6 Mbit |
| JTAG Support | — | Yes (IEEE 1149.1 boundary-scan, ISP) |
| Tension d'alimentation | — | 3.0 V to 3.6 V or 4.75 V to 5.25 V |
| Lead-Free Finish | — | Yes (U suffix) |
| Supported FPGA Families | — | Altera Stratix, Cyclone, APEX, ACEX, Mercury, Excalibur |
| Configuration Mode | — | Passive Serial (PS), JTAG |
| Configuration Time | — | [DATA_NEEDED: typical configuration time] |
| Programming Cycles | — | [DATA_NEEDED: minimum program/erase cycles] |
| Data Retention | — | [DATA_NEEDED: minimum data retention years] |