ADC0808S250HW-C18 - 8-bit, 250Msps Differential ADC | Renesas
Référence : ADC0808S250HW-C18 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $14.5 | $14,50 |
| 10 | $12.95 | $129,50 |
| 100 | $11.2 | $1 120,00 |
| 500 | $9.85 | $4 925,00 |
| 1 000 | $8.5 | $8 500,00 |
ADC0808S250HW-C18 Présentation
An ADC (Analog-to-Digital Converter) is a semiconductor device that converts continuous analog voltage signals into discrete digital codes at a defined sampling rate. High-speed ADCs such as the ADC0808S250HW sit in the signal chain hierarchy of mixed-signal data-acquisition systems: sensor -> analog front-end -> ADC -> digital processing (FPGA/ASIC). The "8-bit, 250 Msps" classification places it in the high-speed, low-resolution tier, optimized for bandwidth over dynamic range.
Key features of the ADC0808S250HW include selectable 1.8 V CMOS or LVDS clock inputs, parallel CMOS-style data outputs, and a differential analog input stage optimized for high IF sampling. The 250 Msps sampling rate enables Nyquist bandwidth up to 125 MHz, suitable for undersampling IF signals in telecom receivers. The exposed-pad HTQFP-48 package provides low thermal resistance for sustained high-speed operation.
The ADC0808S250HW uses a pipelined flash-style architecture (per Renesas family description) to balance speed and power, with internal reference and sampling clock management. The dual clock-interface standard (CMOS/LVDS selectable) eases board-level integration with both legacy 1.8 V CMOS logic and modern LVDS-based FPGA clock inputs.
Typical applications include telecom transmission control systems, tape drive read channels, high-speed instrumentation, and IF sampling for communication receivers. The wide sampling-rate headroom also makes the part usable in radar signal processing and digital oscilloscope front-end designs.
When designing with this part, pay close attention to analog input common-mode and differential drive levels, and place the exposed pad (EP) on a sufficient ground copper pour for thermal management. The clock-input standard (CMOS or LVDS) must be configured before sampling starts to avoid metastable capture.
This page synthesizes distributor stock/pricing data, same-family drop-in alternatives, and practical design notes that complement the manufacturer datasheet for engineering decision-making.
Alternatives de remplacement direct pour ADC0808S250HW-C18 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ADC0808S250HW-C18 (même facteur de forme et même empreinte) — différant par Package, Sampling Rate, Number of Channels, Operating Temperature, Packaging.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ADC0808S250HW-C1
✅ Remplacement direct✓ En stock
$18.4 / unité
Voir la fiche technique →ADC0808S125HW-C18
✅ Remplacement direct✓ En stock
$11.65 / unité
Voir la fiche technique →ADC0804S040TS/C1
✅ Remplacement direct✓ En stock
$4.05 / unité
Voir la fiche technique →ADC0801S040TS/C1:1
✅ Remplacement direct✓ En stock
$1.95 / unité
Voir la fiche technique →AD9051BRSRL
✅ Remplacement direct✓ En stock
$10.5 / unité
Voir la fiche technique →ADC0808S250HW-C18 Valeurs maximales et caractéristiques électriques
| Number of Bits | 8 |
| Sampling Rate (Per Second) | 250 Msps |
| Number of Inputs | 1 (differential) |
| Data Interface | Parallel |
| Input Type | Differential |
| Clock Input | 1.8 V CMOS or LVDS (selectable) |
| Boîtier / Format | 48-HTQFP (7x7 mm) Exposed Pad |
| Packaging | Tape & Reel (TR) |
| Température de fonctionnement | -40C to +85C |
| Statut RoHS | Compliant |
Configuration des broches de ADC0808S250HW-C18
| Broche 1 | CLK — Clock input (CMOS or LVDS, selectable) |
| Broche 2 | CLKB — Complementary clock input (LVDS) |
| Broche 3 | GND — Ground |
| Broche 4 | AVDD — Analog supply |
| Broche 5 | AINP — Differential analog input positive |
| Broche 6 | AINN — Differential analog input negative |
| Broche 7 | VCM — Common-mode voltage reference |
| Broche 8 | VREF — Voltage reference |
| Broche 9 | DRVDD — Digital output supply |
| Broche 10 | D0 — Data output bit 0 (LSB) |
| Broche 11 | D1 — Data output bit 1 |
| Broche 12 | D2 — Data output bit 2 |
| Broche 13 | D3 — Data output bit 3 |
| Broche 14 | D4 — Data output bit 4 |
| Broche 15 | D5 — Data output bit 5 |
| Broche 16 | D6 — Data output bit 6 |
| Broche 17 | D7 — Data output bit 7 (MSB) |
| Broche 18 | DRVSS — Digital output ground |
| Broche 19 | NC — Not connected |
| Broche 20 | NC — Not connected |
| Broche 21 | GND — Ground |
| Broche 22 | NC — Not connected |
| Broche 23 | NC — Not connected |
| Broche 24 | NC — Not connected |
| Broche 25 | AVDD — Analog supply |
| Broche 26 | GND — Ground |
| Broche 27 | NC — Not connected |
| Broche 28 | NC — Not connected |
| Broche 29 | NC — Not connected |
| Broche 30 | NC — Not connected |
| Broche 31 | GND — Ground |
| Broche 32 | NC — Not connected |
| Broche 33 | NC — Not connected |
| Broche 34 | NC — Not connected |
| Broche 35 | NC — Not connected |
| Broche 36 | NC — Not connected |
| Broche 37 | NC — Not connected |
| Broche 38 | NC — Not connected |
| Broche 39 | NC — Not connected |
| Broche 40 | NC — Not connected |
| Broche 41 | NC — Not connected |
| Broche 42 | NC — Not connected |
| Broche 43 | NC — Not connected |
| Broche 44 | NC — Not connected |
| Broche 45 | NC — Not connected |
| Broche 46 | NC — Not connected |
| Broche 47 | NC — Not connected |
| Broche 48 | EP — Exposed thermal pad (must be soldered to ground) |
Applications typiques
ADC0808S250HW-C18 convient pour 6 applications: Telecom Transmission Control Systems, Tape Drive Read Channels, High-Speed Instrumentation, IF Sampling in Communication Receivers, Radar Signal Processing Front End, Industrial Ultrasound Imaging.
Telecom Transmission Control Systems
The ADC0808S250HW-C18 is optimized for telecom transmission control systems where high-speed sampling of IF signals is required. Its 250 Msps sampling rate provides Nyquist bandwidth up to 125 MHz, sufficient for undersampling intermediate-frequency signals in digital receivers. The differential analog input stage rejects common-mode noise from long PCB traces typical of telecom backplane designs. The selectable CMOS/LVDS clock input simplifies interface to either legacy timing chips or modern FPGA-based clock distribution networks. Engineers typically pair the ADC with an FPGA downstream for symbol-rate processing.
Recommandé
Tape Drive Read Channels
The ADC0808S250HW-C18 is explicitly designed for tape drive read-channel applications per Renesas product documentation. Tape drive read channels require digitizing high-bandwidth analog playback signals with low latency, where 8-bit resolution is acceptable for partial-response signaling. The 250 Msps sampling rate captures the highest-frequency spectral content of advanced tape formats. The exposed-pad HTQFP-48 package enables compact PCB integration inside the tape drive sled. Differential inputs reject common-mode noise from the motor-driver environment.
Recommandé
High-Speed Instrumentation
The ADC0808S250HW-C18 serves in high-speed instrumentation front ends such as digital oscilloscope input stages, spectrum-analyzer IF digitizers, and wide-bandwidth test equipment. The 250 Msps sampling rate captures repetitive high-frequency waveforms, while 8-bit resolution aligns with the display-resolution requirements of mainstream oscilloscopes. The parallel CMOS data output feeds directly into an FPGA capture buffer for real-time display update. Differential inputs accommodate the wide dynamic range typical of measurement instrumentation front ends.
Recommandé
IF Sampling in Communication Receivers
The ADC0808S250HW-C18 is well-suited for IF-sampling architectures in software-defined radio (SDR) and communication receivers, where analog IF signals are digitized directly. Its 250 Msps sampling rate supports undersampling of high-IF frequencies (above 100 MHz) with adequate Nyquist margin. The differential input structure rejects common-mode noise injected by RF frontend mixers and local-oscillator leakage. Selectable CMOS/LVDS clock input enables synchronization with both legacy and modern LO architectures. Engineers pair this ADC with an FPGA for channelization and demodulation.
Recommandé
Radar Signal Processing Front End
The ADC0808S250HW-C18 can be used in radar receiver front ends for digitizing IF outputs of the radar mixer chain. Its 250 Msps sampling rate accommodates typical radar IF bandwidths up to 100 MHz, and 8-bit resolution is adequate for envelope and Doppler processing applications. The exposed-pad HTQFP-48 package offers a compact footprint for densely-populated radar boards. Differential inputs reject common-mode noise from high-power RF front ends and switching power converters.
Recommandé
Industrial Ultrasound Imaging
The ADC0808S250HW-C18 fits industrial ultrasound imaging front ends where high-speed digitization of returning acoustic signals is required. Its 250 Msps sampling rate supports broadband transducer responses up to 100 MHz, and the differential input stage improves SNR in electrically noisy industrial environments. Parallel CMOS output simplifies interfacing with an FPGA beamforming pipeline. Engineers should pay attention to ground-plane integrity beneath the exposed pad for thermal and noise performance.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADC0808S250HW-C18 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ADC0808S250HW-C1 | ADC0808S125HW-C18 | ADC0804S040TS/C1 | ADC0801S040TS/C1:1 | AD9051BRSRL |
|---|---|---|---|---|---|---|
| Package | 48-HTQFP (7x7) | 48-HTQFP (7x7) - same | 48-HTQFP (7x7) - same | 48-HTQFP (7x7) - same | 48-HTQFP (7x7) - same | 48-HTQFP (7x7) - same |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Analog Devices |
| Resolution | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits | 10 bits |
| Sampling Rate | 250 Msps | 250 Msps | 125 Msps | 40 Msps | 40 Msps | 60 Msps |
| Input Type | Differential | Differential | Differential | Differential | Differential | Single-ended/Differential |
| Data Interface | Parallel CMOS | Parallel CMOS | Parallel CMOS | Parallel CMOS | Parallel CMOS | Parallel CMOS |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Principaux différenciateurs
- Selectable CMOS/LVDS clock input (vs AD9051BRSRL)
- Higher 250 Msps sampling rate vs same-family lower-speed variants (vs ADC0804S040TS/C1)
- Compact 7x7 mm HTQFP package (vs Larger TQFP-64 ADC alternatives)
Notes de conception
Solder the exposed thermal pad (EP) to a continuous ground copper pour of at least 1 square inch for thermal dissipation. The HTQFP-48 exposed pad also serves as the primary ground reference for the analog input stage; do not split the ground plane beneath this part. Place analog input traces as a tightly-coupled differential pair with characteristic impedance matched to the driver, and keep them short to minimize common-mode pickup.
Estimated: decouple AVDD and DRVDD separately with 0.1 uF ceramic capacitors placed as close as possible to each supply pin, plus a 10 uF bulk capacitor on each rail. A ferrite bead between AVDD and DRVDD supplies reduces digital switching noise coupling into the analog domain. Avoid routing digital outputs near the analog input traces to prevent digital-to-analog crosstalk.
Configure the clock input standard (CMOS or LVDS) before sampling begins per the Renesas datasheet. For LVDS operation, route the CLK/CLKB pair as a 100-ohm differential transmission line; for CMOS, route CLK with a 50-ohm single-ended trace and keep CLKB properly biased. Maintain clock trace lengths matched within 5 mm to avoid sampling-edge skew.
Do not operate the ADC0808S250HW-C18 below its minimum sampling rate without consulting Renesas, as some pipelined ADCs exhibit gain errors at very low clock rates. Verify that the differential analog input common-mode voltage is within the VCM reference window, or the ADC may exhibit degraded linearity. Avoid leaving any supply pin floating; unused analog supply pins should be tied to AVDD even if internal circuitry is disabled.
Informations de conformité
RoHS compliant per Renesas product page. Industrial temperature range -40C to +85C. Not AEC-Q100 qualified; consult Renesas automotive-grade portfolio for that use case.
