ADC10664CIWMX/NOPB - 10-Bit 360ns ADC, 4-Input MUX | Texas Instruments
Référence : ADC10664CIWMX/NOPB ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $8.42 | $8,42 |
| 10 | $7.55 | $75,50 |
| 100 | $6.55 | $655,00 |
| 500 | $5.92 | $2 960,00 |
| 1 000 | $5.31 | $5 310,00 |
ADC10664CIWMX/NOPB Présentation
What is a successive-approximation / multi-step flash ADC? An ADC (analog-to-digital converter) translates a continuous analog voltage into a discrete digital code; the ADC10664 sits in the precision data-acquisition family that uses two lower-resolution flash conversions combined with a residue DAC to resolve higher bits in fewer full-scale steps. In the broader signal-chain taxonomy, the ADC10664 is an ADC -> data converter -> mixed-signal IC -> semiconductor. The integrated analog multiplexer lets one ADC share up to four single-ended sources, eliminating external analog switches in multi-channel scanning designs.
Key features of the ADC10664 include 10 bits of resolution, 4 single-ended analog input channels, a 1.5 MSPS sampling rate, parallel digital output interface, single-ended input type, and a flash-based multi-step architecture. The on-chip sample-and-hold eliminates the need for an external track-and-hold stage. Housed in a wide-body SOIC-28 package, the device is pin-compatible with TI's broader ADC1066x family and supports standard microprocessor parallel bus read cycles.
Architecturally, the ADC10664 uses TI's patented multistep conversion technique that performs two lower-resolution flash conversions and combines them via a switched-capacitor DAC, balancing speed against power dissipation. A self-calibrating ground-reference scheme referenced to the analog supply rejects offset drift over temperature.
Typical applications include process control instrumentation, multiplexed data-acquisition front ends, digitizing oscilloscope input stages, industrial sensor digitizers, and portable instrumentation. The 4-channel input multiplexer makes it well suited for multi-sensor scanning systems. The single +5 V supply simplifies board-level power design in mixed 5 V / 3.3 V systems.
When designing with this part, take care that the analog input does not exceed the supply rails, place a small RC anti-alias filter in front of each MUX channel, and provide a low-impedance reference decoupling network to keep the internal DAC well settled.
This page synthesizes datasheet specifications, distributor pricing and availability, drop-in alternatives from the ADC1066x family, and practical PCB / power design notes not aggregated on a single datasheet page.
Alternatives de remplacement direct pour ADC10664CIWMX/NOPB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ADC10664CIWMX/NOPB (même facteur de forme et même empreinte) — différant par Architecture, Conversion Time, RoHS Status, Package, Power Dissipation.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ADC10664CIWM/NOPB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADC10662CIWM/NOPB
✅ Remplacement direct✓ En stock
$7.81 / unité
Voir la fiche technique →ADC10464CIWMX/NOPB
✅ Remplacement direct✓ En stock
$5.74 / unité
Voir la fiche technique →ADC10664CIWMX/NOPB Valeurs maximales et caractéristiques électriques
| Résolution | 10 bits |
| Number of Inputs | 4 (single-ended, multiplexed) |
| Fréquence d'échantillonnage | 1.5 MSPS |
| Conversion Time | 360 ns (typical, multistep) |
| Architecture | Multistep Flash (patented) |
| Data Interface | Parallel |
| Input Type | Single-Ended |
| Configuration | S/H-ADC (Sample-and-Hold + ADC) |
| Tension d'alimentation de fonctionnement | 5 V (single supply) |
| Power Dissipation | 235 mW (max, per datasheet family) |
| Plage de température de fonctionnement | -40 °C to +85 °C |
| Reference Type | External (per datasheet family) |
| Boîtier / Format | 28-SOIC (0.295", 7.50 mm width) |
| Type de montage | Surface Mount |
| Packaging | Tape & Reel (TR) |
| Statut RoHS | Compliant (NOPB suffix indicates lead-free) |
Configuration des broches de ADC10664CIWMX/NOPB
| Broche 1 | AIN1 — Analog input 1 (single-ended, MUX channel 1) |
| Broche 2 | AIN2 — Analog input 2 (single-ended, MUX channel 2) |
| Broche 3 | AIN3 — Analog input 3 (single-ended, MUX channel 3) |
| Broche 4 | AIN4 — Analog input 4 (single-ended, MUX channel 4) |
| Broche 5 | AGND — Analog ground |
| Broche 6 | VREF+ — External voltage reference positive input |
| Broche 7 | VREF- — External voltage reference negative / return |
| Broche 8 | AVDD — Analog +5 V supply |
| Broche 9 | D0 (LSB) — Parallel digital output D0 (least significant bit) |
| Broche 10 | D1 — Parallel digital output D1 |
| Broche 11 | D2 — Parallel digital output D2 |
| Broche 12 | D3 — Parallel digital output D3 |
| Broche 13 | D4 — Parallel digital output D4 |
| Broche 14 | D5 — Parallel digital output D5 |
| Broche 15 | D6 — Parallel digital output D6 |
| Broche 16 | D7 — Parallel digital output D7 |
| Broche 17 | D8 — Parallel digital output D8 |
| Broche 18 | D9 (MSB) — Parallel digital output D9 (most significant bit) |
| Broche 19 | DGND — Digital ground |
| Broche 20 | DVDD — Digital +5 V supply |
| Broche 21 | RD — Read strobe (active low) |
| Broche 22 | CS — Chip select (active low) |
| Broche 23 | INT — Conversion-complete / interrupt output |
| Broche 24 | CONVST — Conversion start input |
| Broche 25 | MUX_ADDR0 — MUX channel-address select bit 0 |
| Broche 26 | MUX_ADDR1 — MUX channel-address select bit 1 |
| Broche 27 | NC — Not connected (per datasheet) |
| Broche 28 | NC — Not connected (per datasheet) |
Applications typiques
ADC10664CIWMX/NOPB convient pour 6 applications: Process Control Data Acquisition, Multiplexed Sensor Digitizer Module, Digital Oscilloscope Front-End Digitizer, Portable Instrumentation / Battery-Operated Testers, Medical Patient Monitoring (Non-Critical), Automotive Sensor Interface Module.
Process Control Data Acquisition
The ADC10664's 4-input analog multiplexer and 1.5 MSPS sampling rate are well suited to multi-channel industrial process-control boards that read several sensors (pressure, temperature, flow) through a single ADC. Operating from a single +5 V supply over the -40 °C to +85 °C industrial temperature range, it directly meets PLC and DCS front-end requirements. The integrated sample-and-hold removes the need for an external track-and-hold stage, shrinking BOM cost per channel. The parallel digital output streams data into an FPGA or microcontroller data bus at full 1.5 MSPS without DMA bottlenecks. Designers typically pair it with an external low-noise reference (REF02 family) to keep absolute accuracy within the 10-bit budget over the full temperature range.
Recommandé
Multiplexed Sensor Digitizer Module
The 4 single-ended inputs make the ADC10664 a natural fit for scanning up to four sensor sources in sequence. The 1.5 MSPS rate, divided by 4 channels, yields up to 375 kSPS per channel, which is appropriate for vibration, strain-gauge, and load-cell modules used in industrial weighing platforms. Its 235 mW dissipation keeps the junction temperature rise modest without active heatsinking, supporting compact IP65-rated enclosures. The wide-body SOIC-28 footprint gives enough thermal mass for continuous operation at industrial ambient temperatures. Channel-to-channel switching is handled inside the chip with break-before-make logic documented in the datasheet, eliminating external analog-switch crosstalk concerns.
Recommandé
Digital Oscilloscope Front-End Digitizer
The 1.5 MSPS sampling rate and 10-bit resolution are adequate for low-bandwidth oscilloscope front-ends and waveform digitizers used in bench tools and educational lab equipment. The 360 ns conversion time supports single-shot transient capture below 1 MHz signal bandwidth, which covers audio-frequency and slow-edge digital signal analysis. The parallel output interface allows direct DMA into an FPGA capture buffer without latency from serial protocols. Designing with the ADC10664 in this context means providing proper input-protection clamps and AC-coupling because the input range equals the supply rail. The wide-body SOIC package simplifies hand-soldered prototypes for lab-instrument development cycles.
Recommandé
Portable Instrumentation / Battery-Operated Testers
Battery-powered field testers benefit from the ADC10664's relatively low 235 mW dissipation, allowing several hours of operation from a single Li-ion cell when downsampling below 100 kSPS. The single +5 V supply requirement can be derived from a small boost converter or a USB rail, simplifying portable enclosure design. The 4-input MUX lets a single handheld instrument scan a thermocouple, a pressure sensor, a battery monitor, and a calibration source sequentially. The industrial temperature grade ensures reliability in outdoor and field-deployed tools. Add a low-power MCU such as an MSP430 to sequence conversions and forward data over Bluetooth or USB-CDC.
Recommandé
Medical Patient Monitoring (Non-Critical)
The ADC10664 can be used in non-life-critical medical monitoring peripherals such as spirometer flow sensors, body-temperature probes, or pulse-oximeter front-ends where 10-bit resolution at 1.5 MSPS is sufficient. The integrated MUX simplifies multi-sensor patient-cable designs, while the industrial temperature range covers hospital and home-care environments. Designers must implement the IEC 60601 isolation barrier externally because the ADC10664 does not include on-chip galvanic isolation. Add a precision op-amp front end and an external low-noise reference for the required signal-to-noise ratio; medical designs also need the appropriate IEC 60601-1 verification at the system level. The /NOPB lead-free package supports RoHS compliance required in modern medical designs.
Recommandé
Automotive Sensor Interface Module
Although the ADC10664 is industrial-grade rather than AEC-Q100 qualified, it can still be deployed in non-safety automotive subsystems such as cabin HVAC sensors, battery-pack telemetry interfaces, or infotainment auxiliary inputs. The 4-input MUX supports up to four automotive sensors sharing one ADC channel, reducing wire harness complexity. Designers must add input-protection (TVS diodes, series resistors) to meet automotive load-dump and ESD requirements because the ADC10664 does not include on-chip automotive-grade protection. The wide operating temperature range handles under-hood and cabin environments, and the SOIC-28 footprint simplifies PCB rework in prototyping.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADC10664CIWMX/NOPB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ADC10664CIWM/NOPB | ADC10662CIWM/NOPB | ADC10464CIWMX/NOPB |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments (same brand) | Texas Instruments (same brand) | Texas Instruments (same brand) |
| Package | 28-SOIC (0.295", 7.50 mm width) | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same |
| Resolution | 10 bits | 10 bits | 10 bits | 14 bits (higher) |
| Number of Analog Inputs | 4 | 4 | 2 (50% fewer) | 4 |
| Architecture | Multistep Flash (10-bit) | Multistep Flash | Multistep Flash | Multistep Flash |
| Operating Supply Voltage | 5 V | 5 V | 5 V | 5 V |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
Principaux différenciateurs
- Integrated 4-channel analog multiplexer (vs ADC10662CIWM/NOPB)
- Same 28-SOIC footprint across the ADC1066x family (vs ADC10464CIWMX/NOPB)
- Patented multistep flash vs full-flash ADCs (vs Generic full-flash 10-bit ADC)
Notes de conception
Estimated: the ADC10664 draws approximately 47 mA from the +5 V supply at full 1.5 MSPS operation (235 mW / 5 V ≈ 47 mA). When downsampling in portable designs, average supply current scales roughly linearly with the conversion rate. Place a 10 µF tantalum bulk capacitor plus a 100 nF ceramic decoupling capacitor within 5 mm of the AVDD and DVDD pins; keep the analog and digital ground returns separate and join them at a single star point under the ADC to avoid digital switching noise coupling into the analog reference.
Route the analog input traces as a differential pair with a grounded guard to minimize common-mode pickup. Keep digital output traces (D0-D9, RD, CS, INT, CONVST) away from the analog input traces and the VREF traces, using a ground guard trace on both sides. The 28-SOIC wide-body footprint has 0.07 inch lead pitch and tolerates 0.1 µF bypass capacitors placed directly under the package body between pins 5-8 and 19-22. Use a low-impedance power plane on the AVDD/DVDD layer if possible, and avoid routing switching signals on the top layer under the ADC body.
Do not allow the analog input voltage to exceed AVDD or fall below AGND by more than 100 mV, even momentarily, because the input ESD structures can latch up. Always ensure the MUX is set to a valid channel (00, 01, 10, or 11) before issuing CONVST, because undefined MUX_ADDR values may produce invalid conversions. The external reference decoupling network (typically 10 µF + 100 nF) must be physically close to the VREF+ / VREF- pins; long trace inductance between the reference and the ADC's reference input introduces integral non-linearity and gain error. Finally, when cascading ADC10664s for >4 channel designs, do not share the same VREF rail without individual RC filtering per ADC to avoid cross-talk noise injection.
Informations de conformité
/NOPB suffix indicates lead-free, RoHS-compliant orderable variant per TI ordering convention. AEC-Q100 not qualified - industrial temperature grade only. REACH and halogen-free status not stated on the DigiKey/Mouser listings verified.
