ADM237LAQ - 5V RS-232 Transceiver | Analog Devices
Référence : ADM237LAQ ✓ ActifADM237LAQ Présentation
An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a peripheral using the RS-232 electrical standard. Its transmitter translates CMOS logic into RS-232-compatible levels, while its receiver converts the bipolar serial signal back into CMOS logic. Within the interface hierarchy, the ADM237LAQ belongs to the RS-232 transceiver class of interface ICs used for robust point-to-point serial data links.
Key features include a single 5 V supply, compliance with the EIA-232-E and V.28 specifications listed in the manufacturer datasheet, operation at 120 kB/s, and a 9 V output swing generated by the internal DC-DC converter. Small 1 uF charge-pump capacitors reduce board-area requirements. A shutdown function supports power-sensitive systems, while active-in-shutdown receivers can monitor a remote link when the main transmitter circuitry is disabled.
The ADM237LAQ combines multiple drivers and receivers with internal charge-pump circuitry, allowing a compact implementation of an RS-232 port without external level-shifting transistors. Its CMOS implementation is intended for low-power logic systems operating from 5 V. The internal voltage conversion allows the transmitters to produce RS-232-level voltages from the single 5 V supply, reducing the number of external power rails required by the host system.
Typical applications include industrial control links, test equipment, instrumentation, data-acquisition systems, and embedded serial ports. The device is particularly useful where a legacy RS-232 interface must coexist with modern 5 V CMOS logic and where a regulated 5 V supply is available but a separate RS-232 supply is undesirable. The 24-pin ceramic DIP format is suited to through-hole industrial and legacy-system assemblies rather than compact surface-mount designs.
When designing around the ADM237LAQ, place the 1 uF charge-pump capacitors close to their specified pins and route the interface connector and cable ground correctly because RS-232 is a single-ended, bipolar standard. Confirm signal levels and timing at the receiver before assuming a modern serial controller can connect directly. The ceramic DIP package also requires adequate through-hole spacing and appropriate assembly clearances.
This product page consolidates the exact orderable MPN, interface characteristics, package information, design guidance, and sourcing questions into one engineering reference. It also distinguishes documented drop-in substitutions from merely similar RS-232 devices, helping engineers avoid PCB, logic-family, or voltage-swing mismatches during redesign and maintenance.
Alternatives de remplacement direct pour ADM237LAQ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ADM237LAQ (même facteur de forme et même empreinte) — différant par Mounting Type, Package, Product Type.
ADM237LJR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →ADM237LAQ Spécifications
| Product Type | RS-232 Drivers and Receivers Transceiver |
| Tension d'alimentation | 5 V |
| Maximum Data Rate | 120 kB/s |
| RS-232 Output Swing | 9 V |
| Charge-Pump Capacitance | 1 uF |
| Receiver Input Voltage Rating | 30 V |
| Receiver Shutdown Current | 1 uA |
| Driver and Receiver Count | 5:3 |
| Interface Standard | EIA-232-E and V.28 |
| Logic Family | CMOS |
| Power Supply Type | Single 5 V supply |
| Shutdown Control | Yes |
| Receivers Active in Shutdown | Yes |
| On-Board DC-DC Converter | Yes |
| Boîtier | 24-pin ceramic DIP |
| Type de montage | Through-hole |
Guide de configuration des broches du ADM237LAQ 24-pin ceramic dip
Configuration des broches du ADM237LAQ (boîtier 24-pin ceramic dip). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour ADM237LAQ.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ADM237LAQ convient pour 6 applications: Industrial Control Serial Links, Test and Measurement Equipment, Data Acquisition Systems, Embedded Serial Port Expansion, Instrumentation and Sensor Interfaces, Legacy Equipment Maintenance.
Industrial Control Serial Links
The ADM237LAQ fits legacy industrial controllers that expose a 5 V CMOS logic interface and require an RS-232 connection to equipment such as drives, indicators, or service consoles. Its documented 120 kB/s data rate covers many supervisory and configuration protocols, while the internal DC-DC converter produces a 9 V output swing from one 5 V rail. The 24-pin ceramic DIP supports through-hole assemblies and field-replaceable controller boards. Designers should preserve the specified 1 uF charge-pump capacitors, validate grounding at the connector, and test the protocol timing across the full operating environment.
Recommandé
Test and Measurement Equipment
ADM237LAQ is suitable for laboratory instruments and test systems that retain RS-232 ports for host-computer control, calibration, or legacy peripheral compatibility. The 5 V supply and 120 kB/s rate support a compact controller implementation without requiring a separate transmitter supply. Its 5:3 driver and receiver organization allows several RS-232 lines to be managed in one interface IC. Keep the 1 uF charge-pump capacitors close to the device pins, provide a continuous signal-ground path, and verify that the host UART, cable length, and framing are compatible with the target instrument.
Recommandé
Data Acquisition Systems
The ADM237LAQ can connect a data-acquisition controller or embedded instrument to a host computer over RS-232 when the system already uses 5 V CMOS logic. Its documented 120 kB/s ceiling accommodates moderate-rate command, status, and measurement traffic, and the internal DC-DC converter provides the required 9 V transmit swing from a single 5 V source. The 24-pin ceramic DIP is practical for legacy through-hole acquisition boards that need field replacement. Designers should test the complete cable and grounding arrangement because command latency and data integrity can be affected by wiring, interference, and protocol overhead.
Recommandé
Embedded Serial Port Expansion
ADM237LAQ provides a practical path for adding an RS-232 port to a 5 V embedded controller that lacks a native RS-232 physical layer. The device combines five drivers and three receivers, supports rates up to 120 kB/s, and generates a 9 V output swing through its on-board converter. That integration reduces the number of external discrete level shifters and support components. The through-hole ceramic DIP package suits retrofit boards rather than highly compact new products. Firmware must provide framing and error handling because RS-232 is a point-to-point physical interface and does not itself define a command protocol.
Recommandé
Instrumentation and Sensor Interfaces
The ADM237LAQ is appropriate for instrumentation modules that must communicate with an older RS-232 host while operating internally from 5 V. The 120 kB/s data rate and 9 V output swing meet common low-to-moderate-rate instrument-control requirements, while shutdown can reduce consumption when the interface is idle. Its receiver input tolerance of 30 V provides additional margin for common wiring conditions, although the design still needs appropriate protection. Preserve the datasheet capacitor layout, use a low-impedance connector ground, and validate command integrity with the intended cable before production deployment.
Recommandé
Legacy Equipment Maintenance
ADM237LAQ is useful for maintaining older RS-232-equipped equipment where a ceramic DIP transceiver is already specified on the board and replacement should not require a layout redesign. The part consolidates drivers, receivers, shutdown control, and the charge-pump converter into one 24-pin package. Its single 5 V supply arrangement can simplify repair-board power requirements compared with designs using external transmitter circuitry. Technicians should confirm the exact pin assignment, observe electrostatic-handling precautions, and observe capacitor polarity if polarized capacitors are used. Substitution should be based on the exact electrical and mechanical requirements of the failed assembly.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADM237LAQ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit |
|---|---|
| Brand | Analog Devices |
| Package | 24-pin ceramic DIP |
| Supply Voltage | 5 V |
| Maximum Data Rate | 120 kB/s |
| RS-232 Output Swing | 9 V |
| Driver and Receiver Count | 5:3 |
| Charge-Pump Capacitance | 1 uF |
| Receiver Input Voltage Rating | 30 V |
| Shutdown Receiver Current | 1 uA |
| Interface Standards | EIA-232-E and V.28 |
Principaux différenciateurs
- Single-supply 9 V RS-232 output swing (vs ADM207EARSZ-REEL)
- Original 24-pin ceramic-DIP configuration (vs ADM207EARSZ-REEL)
- Shutdown operation with active receivers (vs ADM207EARSZ-REEL)
Notes de conception
Place the specified 1 uF charge-pump capacitors close to the ADM237LAQ pins identified in the manufacturer datasheet, and keep their return-current paths short. These capacitors support the on-board DC-DC converter that produces the documented 9 V RS-232 output swing. Avoid placing long traces between the capacitor terminals and the device, and route the high-current charge-pump paths away from sensitive receiver inputs to reduce potential switching disturbance.
Do not treat a generally similar RS-232 transceiver as a drop-in replacement for ADM237LAQ. The replacement must match the 24-pin ceramic DIP footprint, 5 V CMOS logic interface, 5:3 channel arrangement, shutdown behavior, and charge-pump implementation. ADM207EARSZ-REEL has a different ordering and package context and is not established as pin-compatible. Verify the manufacturer pinout and electrical table for every proposed substitution.
Use a stable 5 V supply with low impedance at the ADM237LAQ supply pins. The internal converter creates the 9 V transmit swing, so inadequate supply decoupling can reduce output level or introduce disturbance into adjacent logic. Follow the manufacturer connection diagram for bypass components and keep the RS-232 connector return connected to the circuit ground through a short, appropriately designed path.
RS-232 uses bipolar single-ended signaling, so cable routing and ground quality influence noise immunity. Keep the interface connector ground continuous, minimize loop area, and separate the RS-232 route from sensitive sensor or timing traces. Although the ADM237LAQ receiver input is rated to 30 V, that rating is not a substitute for surge protection or overvoltage protection in exposed industrial cabling.
Informations de conformité
The manufacturer datasheet feature information does not state the requested environmental or substance-compliance classifications. AEC-Q100 is recorded as not applicable because the part is an industrial RS-232 interface IC rather than an automotive-qualified device.