ADM237LAQ - 5V RS-232 Transceiver | Analog Devices
料号: ADM237LAQ ✓ 量产中ADM237LAQ 概述
An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a peripheral using the RS-232 electrical standard. Its transmitter translates CMOS logic into RS-232-compatible levels, while its receiver converts the bipolar serial signal back into CMOS logic. Within the interface hierarchy, the ADM237LAQ belongs to the RS-232 transceiver class of interface ICs used for robust point-to-point serial data links.
Key features include a single 5 V supply, compliance with the EIA-232-E and V.28 specifications listed in the manufacturer datasheet, operation at 120 kB/s, and a 9 V output swing generated by the internal DC-DC converter. Small 1 uF charge-pump capacitors reduce board-area requirements. A shutdown function supports power-sensitive systems, while active-in-shutdown receivers can monitor a remote link when the main transmitter circuitry is disabled.
The ADM237LAQ combines multiple drivers and receivers with internal charge-pump circuitry, allowing a compact implementation of an RS-232 port without external level-shifting transistors. Its CMOS implementation is intended for low-power logic systems operating from 5 V. The internal voltage conversion allows the transmitters to produce RS-232-level voltages from the single 5 V supply, reducing the number of external power rails required by the host system.
Typical applications include industrial control links, test equipment, instrumentation, data-acquisition systems, and embedded serial ports. The device is particularly useful where a legacy RS-232 interface must coexist with modern 5 V CMOS logic and where a regulated 5 V supply is available but a separate RS-232 supply is undesirable. The 24-pin ceramic DIP format is suited to through-hole industrial and legacy-system assemblies rather than compact surface-mount designs.
When designing around the ADM237LAQ, place the 1 uF charge-pump capacitors close to their specified pins and route the interface connector and cable ground correctly because RS-232 is a single-ended, bipolar standard. Confirm signal levels and timing at the receiver before assuming a modern serial controller can connect directly. The ceramic DIP package also requires adequate through-hole spacing and appropriate assembly clearances.
This product page consolidates the exact orderable MPN, interface characteristics, package information, design guidance, and sourcing questions into one engineering reference. It also distinguishes documented drop-in substitutions from merely similar RS-232 devices, helping engineers avoid PCB, logic-family, or voltage-swing mismatches during redesign and maintenance.
直接替换替代料: ADM237LAQ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADM237LAQ (相同外形与封装尺寸) ——差异在于 Mounting Type, Package, Product Type.
ADM237LAQ 规格参数
| Product Type | RS-232 Drivers and Receivers Transceiver |
| 电源电压 | 5 V |
| Maximum Data Rate | 120 kB/s |
| RS-232 Output Swing | 9 V |
| Charge-Pump Capacitance | 1 uF |
| Receiver Input Voltage Rating | 30 V |
| Receiver Shutdown Current | 1 uA |
| Driver and Receiver Count | 5:3 |
| Interface Standard | EIA-232-E and V.28 |
| Logic Family | CMOS |
| Power Supply Type | Single 5 V supply |
| Shutdown Control | Yes |
| Receivers Active in Shutdown | Yes |
| On-Board DC-DC Converter | Yes |
| 封装 | 24-pin ceramic DIP |
| 安装类型 | Through-hole |
ADM237LAQ 24-pin ceramic dip 引脚配置指南
ADM237LAQ(24-pin ceramic dip 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ADM237LAQ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADM237LAQ 适用于 6 应用s: Industrial Control Serial Links, Test and Measurement Equipment, Data Acquisition Systems, Embedded Serial Port Expansion, Instrumentation and Sensor Interfaces, Legacy Equipment Maintenance.
Industrial Control Serial Links
The ADM237LAQ fits legacy industrial controllers that expose a 5 V CMOS logic interface and require an RS-232 connection to equipment such as drives, indicators, or service consoles. Its documented 120 kB/s data rate covers many supervisory and configuration protocols, while the internal DC-DC converter produces a 9 V output swing from one 5 V rail. The 24-pin ceramic DIP supports through-hole assemblies and field-replaceable controller boards. Designers should preserve the specified 1 uF charge-pump capacitors, validate grounding at the connector, and test the protocol timing across the full operating environment.
推荐
Test and Measurement Equipment
ADM237LAQ is suitable for laboratory instruments and test systems that retain RS-232 ports for host-computer control, calibration, or legacy peripheral compatibility. The 5 V supply and 120 kB/s rate support a compact controller implementation without requiring a separate transmitter supply. Its 5:3 driver and receiver organization allows several RS-232 lines to be managed in one interface IC. Keep the 1 uF charge-pump capacitors close to the device pins, provide a continuous signal-ground path, and verify that the host UART, cable length, and framing are compatible with the target instrument.
推荐
Data Acquisition Systems
The ADM237LAQ can connect a data-acquisition controller or embedded instrument to a host computer over RS-232 when the system already uses 5 V CMOS logic. Its documented 120 kB/s ceiling accommodates moderate-rate command, status, and measurement traffic, and the internal DC-DC converter provides the required 9 V transmit swing from a single 5 V source. The 24-pin ceramic DIP is practical for legacy through-hole acquisition boards that need field replacement. Designers should test the complete cable and grounding arrangement because command latency and data integrity can be affected by wiring, interference, and protocol overhead.
推荐
Embedded Serial Port Expansion
ADM237LAQ provides a practical path for adding an RS-232 port to a 5 V embedded controller that lacks a native RS-232 physical layer. The device combines five drivers and three receivers, supports rates up to 120 kB/s, and generates a 9 V output swing through its on-board converter. That integration reduces the number of external discrete level shifters and support components. The through-hole ceramic DIP package suits retrofit boards rather than highly compact new products. Firmware must provide framing and error handling because RS-232 is a point-to-point physical interface and does not itself define a command protocol.
推荐
Instrumentation and Sensor Interfaces
The ADM237LAQ is appropriate for instrumentation modules that must communicate with an older RS-232 host while operating internally from 5 V. The 120 kB/s data rate and 9 V output swing meet common low-to-moderate-rate instrument-control requirements, while shutdown can reduce consumption when the interface is idle. Its receiver input tolerance of 30 V provides additional margin for common wiring conditions, although the design still needs appropriate protection. Preserve the datasheet capacitor layout, use a low-impedance connector ground, and validate command integrity with the intended cable before production deployment.
推荐
Legacy Equipment Maintenance
ADM237LAQ is useful for maintaining older RS-232-equipped equipment where a ceramic DIP transceiver is already specified on the board and replacement should not require a layout redesign. The part consolidates drivers, receivers, shutdown control, and the charge-pump converter into one 24-pin package. Its single 5 V supply arrangement can simplify repair-board power requirements compared with designs using external transmitter circuitry. Technicians should confirm the exact pin assignment, observe electrostatic-handling precautions, and observe capacitor polarity if polarized capacitors are used. Substitution should be based on the exact electrical and mechanical requirements of the failed assembly.
推荐
推荐产品汇总
工程参考数据: ADM237LAQ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Brand | Analog Devices |
| Package | 24-pin ceramic DIP |
| Supply Voltage | 5 V |
| Maximum Data Rate | 120 kB/s |
| RS-232 Output Swing | 9 V |
| Driver and Receiver Count | 5:3 |
| Charge-Pump Capacitance | 1 uF |
| Receiver Input Voltage Rating | 30 V |
| Shutdown Receiver Current | 1 uA |
| Interface Standards | EIA-232-E and V.28 |
关键差异点
- Single-supply 9 V RS-232 output swing (对比 ADM207EARSZ-REEL)
- Original 24-pin ceramic-DIP configuration (对比 ADM207EARSZ-REEL)
- Shutdown operation with active receivers (对比 ADM207EARSZ-REEL)
设计说明
Place the specified 1 uF charge-pump capacitors close to the ADM237LAQ pins identified in the manufacturer datasheet, and keep their return-current paths short. These capacitors support the on-board DC-DC converter that produces the documented 9 V RS-232 output swing. Avoid placing long traces between the capacitor terminals and the device, and route the high-current charge-pump paths away from sensitive receiver inputs to reduce potential switching disturbance.
Do not treat a generally similar RS-232 transceiver as a drop-in replacement for ADM237LAQ. The replacement must match the 24-pin ceramic DIP footprint, 5 V CMOS logic interface, 5:3 channel arrangement, shutdown behavior, and charge-pump implementation. ADM207EARSZ-REEL has a different ordering and package context and is not established as pin-compatible. Verify the manufacturer pinout and electrical table for every proposed substitution.
Use a stable 5 V supply with low impedance at the ADM237LAQ supply pins. The internal converter creates the 9 V transmit swing, so inadequate supply decoupling can reduce output level or introduce disturbance into adjacent logic. Follow the manufacturer connection diagram for bypass components and keep the RS-232 connector return connected to the circuit ground through a short, appropriately designed path.
RS-232 uses bipolar single-ended signaling, so cable routing and ground quality influence noise immunity. Keep the interface connector ground continuous, minimize loop area, and separate the RS-232 route from sensitive sensor or timing traces. Although the ADM237LAQ receiver input is rated to 30 V, that rating is not a substitute for surge protection or overvoltage protection in exposed industrial cabling.
合规信息
The manufacturer datasheet feature information does not state the requested environmental or substance-compliance classifications. AEC-Q100 is recorded as not applicable because the part is an industrial RS-232 interface IC rather than an automotive-qualified device.