ADS62P25IRGC25 - Dual 12-Bit 125 MSPS ADC, 64-VQFN | Texas Instruments
Référence : ADS62P25IRGC25 ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $48.2 | $48,20 |
| 10 | $43.85 | $438,50 |
| 100 | $39.4 | $3 940,00 |
| 500 | $35.95 | $17 975,00 |
| 1 000 | $32.5 | $32 500,00 |
ADS62P25IRGC25 Présentation
An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous analog voltages and quantizes them into discrete digital codes. The ADS62P25 sits in the high-speed pipeline ADC family, used when systems require many tens of megasamples per second per channel for communications, imaging, or instrumentation. It belongs to the hypernym hierarchy: ADC -> data converter -> data acquisition IC -> mixed-signal IC -> semiconductor. Pipeline ADCs specifically use a switched-capacitor architecture that resolves a few bits per stage across cascaded stages to achieve high sample rates at moderate resolution, which is exactly the architecture used here.
Key features include 12-bit resolution with no missing codes, 125 MSPS maximum sample rate, programmable fine gain up to 6 dB plus a 3.5 dB coarse gain for SNR/SFDR trade-off, 95 dB channel-to-channel crosstalk, and a built-in digital processing block with offset correction and fine gain correction in 0.05 dB steps. Selectable DDR LVDS or parallel CMOS outputs let the same hardware target FPGA-based capture boards or legacy parallel DSP interfaces. The integrated low-jitter clock buffer simplifies board design by relaxing external clock requirements.
Typical applications include multi-carrier GSM/UMTS/LTE base-station receivers, cable-headend digitizers, medical imaging front ends, radar and phased-array IF sampling, and test and measurement instrumentation. The wide input bandwidth and selectable output interfaces make it well suited for both diversity receivers and multi-channel oscilloscope platforms.
When designing with this device, treat the analog input network and clock distribution as a single RF subsystem: use a differential transformer driver, keep the clock path short, and provide adequate decoupling on each supply pin. The dual-channel footprint requires that both inputs be impedance-matched to achieve the rated crosstalk and SFDR. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone.
Alternatives de remplacement direct pour ADS62P25IRGC25 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ADS62P25IRGC25 (même facteur de forme et même empreinte) — différant par Input Type, Package, Output Interface, Architecture, Number of Channels.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
ADS62P25IRGCT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ADS62P23IRGC25
✅ Remplacement direct✓ En stock
$18.85 / unité
Voir la fiche technique →ADS62P22IRGC25
✅ Remplacement direct✓ En stock
$15.5 / unité
Voir la fiche technique →ADS62P25IRGCR
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
ADS62P28IRGC25
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$17.5 / unité
Voir la fiche technique →ADS62P25IRGC25 Valeurs maximales et caractéristiques électriques
| Résolution | 12 bit |
| Number of Channels | 2 |
| Maximum Sample Rate | 125 MSPS |
| Architecture | Pipelined |
| Input Type | Differential analog |
| Output Interface | Parallel CMOS or DDR LVDS (selectable) |
| No Missing Codes | 12-bit (guaranteed) |
| Channel-to-Channel Crosstalk | 95 dB |
| Coarse Gain | 3.5 dB |
| Programmable Fine Gain | up to 6 dB |
| Digital Processing Block | Offset correction, fine gain correction (0.05 dB steps) |
| Clock Input | Integrated low-jitter clock buffer |
| Boîtier | 64-pin VQFN (RGC), 9x9 mm |
| Plage de température de fonctionnement | -40C to +85C (Industrial) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant |
Configuration des broches de ADS62P25IRGC25
| Broche 1 | INA_P — Analog input A positive (differential) |
| Broche 2 | INA_N — Analog input A negative (differential) |
| Broche 3 | VCM — Common-mode voltage output for input bias |
| Broche 4 | INB_P — Analog input B positive (differential) |
| Broche 5 | INB_N — Analog input B negative (differential) |
| Broche 6 | CLKP — Differential clock input positive |
| Broche 7 | CLKN — Differential clock input negative |
| Broche 8 | SCLK — Serial interface clock |
| Broche 9 | SDATA — Serial interface data |
| Broche 10 | SEN — Serial interface enable |
| Broche 11 | RESET — Hardware reset (active low) |
| Broche 12 | PDN — Power-down control |
| Broche 13 | MODE — Output mode select (CMOS/LVDS) |
| Broche 14 | NC — Not connected (per datasheet) |
| Broche 15 | D0A — Channel A data output bit 0 (LSB) |
| Broche 16 | D1A — Channel A data output bit 1 |
| Broche 17 | D2A — Channel A data output bit 2 |
| Broche 18 | D3A — Channel A data output bit 3 |
| Broche 19 | D4A — Channel A data output bit 4 |
| Broche 20 | D5A — Channel A data output bit 5 |
| Broche 21 | D6A — Channel A data output bit 6 |
| Broche 22 | D7A — Channel A data output bit 7 |
| Broche 23 | D8A — Channel A data output bit 8 |
| Broche 24 | D9A — Channel A data output bit 9 |
| Broche 25 | D10A — Channel A data output bit 10 |
| Broche 26 | D11A — Channel A data output bit 11 (MSB) |
| Broche 27 | CLKOUTA_P — Channel A output clock positive (LVDS) |
| Broche 28 | CLKOUTA_N — Channel A output clock negative (LVDS) |
| Broche 29 | D0B — Channel B data output bit 0 (LSB) |
| Broche 30 | D1B — Channel B data output bit 1 |
| Broche 31 | D2B — Channel B data output bit 2 |
| Broche 32 | D3B — Channel B data output bit 3 |
| Broche 33 | D4B — Channel B data output bit 4 |
| Broche 34 | D5B — Channel B data output bit 5 |
| Broche 35 | D6B — Channel B data output bit 6 |
| Broche 36 | D7B — Channel B data output bit 7 |
| Broche 37 | D8B — Channel B data output bit 8 |
| Broche 38 | D9B — Channel B data output bit 9 |
| Broche 39 | D10B — Channel B data output bit 10 |
| Broche 40 | D11B — Channel B data output bit 11 (MSB) |
| Broche 41 | CLKOUTB_P — Channel B output clock positive (LVDS) |
| Broche 42 | CLKOUTB_N — Channel B output clock negative (LVDS) |
| Broche 43 | NC — Not connected (per datasheet) |
| Broche 44 | NC — Not connected (per datasheet) |
| Broche 45 | AVDD33 — Analog 3.3V supply |
| Broche 46 | AVDD33 — Analog 3.3V supply |
| Broche 47 | AVDD18 — Analog 1.8V supply |
| Broche 48 | AVDD18 — Analog 1.8V supply |
| Broche 49 | AVDD18 — Analog 1.8V supply |
| Broche 50 | AVDD18 — Analog 1.8V supply |
| Broche 51 | DRVDD — Digital output driver supply |
| Broche 52 | DRVDD — Digital output driver supply |
| Broche 53 | DVDD — Digital 1.8V supply |
| Broche 54 | DVDD — Digital 1.8V supply |
| Broche 55 | DVDD — Digital 1.8V supply |
| Broche 56 | NC — Not connected (per datasheet) |
| Broche 57 | NC — Not connected (per datasheet) |
| Broche 58 | NC — Not connected (per datasheet) |
| Broche 59 | NC — Not connected (per datasheet) |
| Broche 60 | NC — Not connected (per datasheet) |
| Broche 61 | NC — Not connected (per datasheet) |
| Broche 62 | NC — Not connected (per datasheet) |
| Broche 63 | NC — Not connected (per datasheet) |
| Broche 64 | NC — Not connected (per datasheet) |
Applications typiques
ADS62P25IRGC25 convient pour 6 applications: Multi-Carrier Wireless Base Station Receiver, Cable Headend Digitizer, Medical Ultrasound Beamformer Front End, Wideband Radar and Phased-Array IF Sampling, Test and Measurement Instrumentation, Software Defined Radio (SDR) Receiver.
Multi-Carrier Wireless Base Station Receiver
The ADS62P25IRGC25 is well matched to multi-carrier GSM/UMTS/LTE base-station receivers where two diversity channels must be digitized simultaneously. Its dual 12-bit channels at 125 MSPS comfortably handle wideband IF signals, and the 95 dB channel-to-channel crosstalk preserves isolation between diversity branches. The selectable DDR LVDS output pairs directly with FPGAs from Xilinx Altera, simplifying timing closure at high sample rates. Per the TI ADS62P25 datasheet, the integrated low-jitter clock buffer relaxes clock-tree design while still delivering the SNR/SFDR required by 3G/4G receiver chains. The 64-VQFN (RGC) footprint keeps the analog front-end compact enough to fit behind the antenna feed network on a typical remote-radio-head PCB.
Recommandé
Cable Headend Digitizer
Cable-headend equipment digitizes upstream and downstream QAM carriers at IF, and the ADS62P25IRGC25 is a strong fit because its 125 MSPS rate captures several adjacent carriers per channel. The 12-bit resolution and no-missing-codes guarantee preserve modulation error ratio (MER) under real-world cable impairments, while the 95 dB crosstalk keeps dual upstream paths isolated. Designers can use the parallel CMOS output mode to drive legacy QAM demodulator ASICs, or DDR LVDS for modern FPGA-based demodulation. Per TI datasheet guidance, the differential analog inputs accept the typical IF transformer network used in cable downstream receivers without external buffer amplifiers.
Recommandé
Medical Ultrasound Beamformer Front End
Ultrasound beamformer front ends require many simultaneous low-noise ADC channels, and the ADS62P25IRGC25 is well suited because its dual-channel 12-bit architecture reduces PCB area in dense probe arrays. The 125 MSPS rate covers the 40 MHz IF bandwidth typical of premium ultrasound probes, while the digital offset and fine gain correction blocks compensate for channel-to-channel analog mismatches. Per the TI ADS62P25 datasheet, the LVDS output simplifies routing across the dozens of channels feeding the beamformer FPGA. The industrial -40C to +85C temperature range also supports portable cart-based systems that see wider thermal swings than a fixed clinical room.
Recommandé
Wideband Radar and Phased-Array IF Sampling
Phased-array radar systems digitize multiple IF channels in parallel and need ADCs with tightly matched gain and phase. The ADS62P25IRGC25 delivers dual 12-bit 125 MSPS channels in one package, which keeps the analog signal path short and matched for accurate beamforming. The selectable DDR LVDS output and low-jitter integrated clock buffer preserve the timing relationships critical to angle-of-arrival accuracy. Per TI, the digital processing block with fine gain correction in 0.05 dB steps enables precise per-channel calibration. The VQFN-64 footprint is small enough to fit behind each radiating element's T/R module in high-density electronically steered arrays.
Recommandé
Test and Measurement Instrumentation
Bench oscilloscopes, spectrum analyzers, and arbitrary waveform digitizers use ADCs like the ADS62P25IRGC25 to capture wideband repetitive and transient signals. The 125 MSPS sample rate captures signals well above the audio band, while the dual channels handle differential probes or two simultaneous time bases. The programmable fine gain up to 6 dB lets designers trade SNR against SFDR depending on whether they emphasize noise floor or harmonic distortion in measurement results. Per the TI ADS62P25 datasheet, the LVDS CMOS-selectable interface supports both modern FPGA-based scopes and legacy parallel-bus instruments without redesigning the analog front end.
Recommandé
Software Defined Radio (SDR) Receiver
Software defined radio platforms rely on wideband ADC front ends to push as much signal chain as possible into the digital domain, and the ADS62P25IRGC25 fits this role well. Two independent 12-bit 125 MSPS channels capture I/Q signal pairs from a single RF mixer with closely matched gain and phase. The DDR LVDS output streams up to several Gbps of data into an FPGA for digital downconversion and channelization. Per TI, the integrated low-jitter clock buffer simplifies the LO-to-ADC clock distribution and preserves SNR across the full Nyquist bandwidth. Designers benefit from a single 64-VQFN device replacing two single-channel ADCs in space-constrained SDR modules.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ADS62P25IRGC25 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ADS62P25IRGCT | ADS62P23IRGC25 | ADS62P22IRGC25 | ADS62P25IRGCR | ADS62P28IRGC25 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | VQFN-64 (RGC) 9x9 mm | VQFN-64 (RGC) 9x9 mm - same | VQFN-64 (RGC) 9x9 mm - same | VQFN-64 (RGC) 9x9 mm - same | VQFN-64 (RGC) 9x9 mm - same | VQFN-64 (RGC) 9x9 mm - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 14 bit |
| Maximum Sample Rate | 125 MSPS | 125 MSPS | 80 MSPS | 65 MSPS | 125 MSPS | 105 MSPS |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Interface | CMOS or DDR LVDS | CMOS or DDR LVDS | CMOS or DDR LVDS | CMOS or DDR LVDS | CMOS or DDR LVDS | CMOS or DDR LVDS |
| Architecture | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Principaux différenciateurs
- Highest sample rate in the ADS62P2X 12-bit family (vs ADS62P23IRGC25 (80 MSPS))
- Dual-channel integration reduces PCB area versus two single-channel ADCs (vs Two discrete 12-bit single-channel ADCs)
- Selectable DDR LVDS or CMOS output in one device (vs ADS62P22IRGC25 (65 MSPS variant))
Notes de conception
The ADS62P25IRGC25 requires careful PCB layout to achieve rated SFDR. Place a continuous ground plane on layer 2 beneath the analog input traces, keep input traces matched in length and width, and use a transformer-coupled differential input network on INA_P/INA_N and INB_P/INB_N. Per the TI ADS62P25 datasheet, the exposed thermal pad must be soldered to a low-impedance ground pour with multiple stitching vias for thermal dissipation.
Decouple each AVDD33, AVDD18, DVDD, and DRVDD pin with a 0.1uF ceramic capacitor placed within 2 mm of the pin, plus a 10uF bulk capacitor per supply rail. Use a ferrite bead or pi-filter to isolate the analog 3.3V supply from the digital 3.3V supply if both rails share an upstream LDO. Per TI, inadequate decoupling is the most common cause of degraded SNR and SFDR on the ADS62P2X family.
Route the differential clock input (CLKP/CLKN) with controlled 100-ohm differential impedance and keep it away from switching digital outputs. The integrated low-jitter clock buffer accepts a wide range of clock amplitudes, but a clean sinusoidal or LVPECL driver is recommended for best jitter performance. Per TI, the clock path should be treated as an RF signal and not as a digital control line.
Do not exceed the absolute maximum analog input voltage on INA or INB pins; the integrated ESD diodes are sensitive to over-voltage events at power-up before the analog supply rail settles. Sequence AVDD33 first, then AVDD18/DVDD, and only after both rails are stable should the clock and analog input be applied. Per the TI ADS62P25 datasheet, failure to sequence supplies can permanently damage the device.
Informations de conformité
RoHS compliance confirmed via TI product page. Industrial temperature grade -40C to +85C. AEC-Q100 not applicable since this is an industrial-grade ADC; automotive versions would be specified differently.
