AT90USB162-16MU - 16MHz AVR USB MCU | Microchip Technology
Référence : AT90USB162-16MU ✓ ActifAT90USB162-16MU Présentation
An 8-bit AVR microcontroller is a compact embedded processor intended for control-oriented products that coordinate peripherals, read sensors, update displays, and manage communication links. Its RISC-oriented instruction set, working registers, and dedicated peripheral modules place the AT90USB162 within the hierarchy of microcontrollers, embedded processors, and semiconductor control devices. The product is particularly relevant to USB-connected human-interface, communications, and compact embedded-control designs.
Key features include 16 KB of read-while-write ISP Flash, 512 bytes of EEPROM, and 512 bytes of SRAM. The device provides 22 general-purpose I/O lines and 32 general-purpose working registers. Two flexible timer/counters with compare modes and PWM, a USART, SPI, and a programmable watchdog timer support typical embedded-control duties. Its 16 MHz maximum clock speed provides approximately one MIPS-per-MHz-class execution capability for its AVR-enhanced RISC architecture.
The AT90USB162 architecture integrates USB interface hardware with an 8-bit AVR core, allowing a compact design to connect to a USB host without implementing a separate USB controller. ISP Flash supports in-system programming, while read-while-write operation allows nonvolatile code storage to remain useful during certain programming operations. The manufacturer describes the family as a low-power CMOS implementation combining 16 KB ISP Flash with 512-byte EEPROM and 512-byte SRAM.
Typical applications include USB human-interface devices, firmware update and bootloader equipment, USB-to-serial adapters, compact data-acquisition controllers, and industrial peripherals. The 22 I/O lines provide interfaces for buttons, indicators, sensors, and external transceivers, while the timers, USART, and SPI broaden its usefulness beyond a basic USB bridge. The 32-VQFN footprint is appropriate for compact USB accessories and embedded modules.
Board design requires careful attention to USB signal integrity, exposed-pad soldering, decoupling, and programming access. Place the USB traces according to the manufacturer reference layout, keep the exposed thermal pad soldered to the ground plane, and provide local bulk and high-frequency bypass capacitors close to the supply pins. Confirm the exact pin functions and alternate-pin assignments in the Microchip pin-description table before routing the PCB.
This page combines the AT90USB162 family specifications, package information, documented drop-in family alternatives, application guidance, and design-focused comparisons to help engineers evaluate USB MCU integration before schematic capture and PCB layout.
Alternatives de remplacement direct pour AT90USB162-16MU — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec AT90USB162-16MU (même facteur de forme et même empreinte) — différant par Package, General-Purpose I/O Lines, General-Purpose Working Registers, Program Memory, Programming Interface.
AT90USB162-16AU
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →AT90USB162-16AUR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AT90USB162-16MU-KUMA
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AT90USB162-16MUR
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
AT90USB82-16MU
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →AT90USB162-16MU Valeurs maximales et caractéristiques électriques
| Microcontroller Type | 8-bit AVR RISC-based microcontroller |
| Fréquence d'horloge maximale | 16 MHz |
| Flash Memory | 16 KB (16K x 8) |
| EEPROM Memory | 512 bytes |
| SRAM | 512 bytes |
| General-Purpose I/O Lines | 22 |
| General-Purpose Working Registers | 32 |
| Architecture | AVR-enhanced RISC |
| Timer/Counter Count | 2 |
| Timer Features | Compare modes and PWM |
| Serial Interfaces | USART and SPI |
| Watchdog Timer | Programmable |
| Programming Interface | In-System Programming (ISP) |
| Read-While-Write Flash | Supported |
| Boîtier | 32-VQFN, 5 x 5 mm |
| Type de montage | Surface mount |
Guide de configuration des broches du AT90USB162-16MU 32-vqfn, 5 x 5 mm
Configuration des broches du AT90USB162-16MU (boîtier 32-vqfn, 5 x 5 mm). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour AT90USB162-16MU.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
AT90USB162-16MU convient pour 6 applications: USB Human-Interface Devices, USB Bootloader and Firmware Update, USB-to-Serial Communication Adapter, Compact Industrial Data Acquisition, USB Connected Test and Control Module, USB Motor and actuator Controller.
USB Human-Interface Devices
The AT90USB162-16MU fits a USB keyboard, control panel, game controller, or other human-interface device because it combines a 16 MHz AVR core with USB connectivity, 22 general-purpose I/O lines, and timers with PWM and compare modes. Buttons, LEDs, encoders, and status indicators can be connected through the GPIO and timer resources while the USB interface handles enumeration and data exchange. The 32-VQFN 5 x 5 mm package also allows a compact implementation. PCB design must preserve the manufacturer's USB trace geometry, provide local supply bypassing, and verify the selected crystal or clock configuration before firmware development.
Recommandé
USB Bootloader and Firmware Update
The AT90USB162-16MU is appropriate for USB-connected firmware update equipment because it combines 16 KB of read-while-write ISP Flash with an integrated USB interface and 512 bytes of EEPROM. A bootloader can occupy the protected boot section, detect an update request, exchange data over USB, and resume the application after validation. The 16 MHz operating speed provides useful execution throughput for protocol handling, while 22 GPIO lines can support recovery buttons, status LEDs, and boot-mode control. Designers should protect bootloader and application boundaries, follow the ISP programming sequence, and verify the exact Flash organization in the manufacturer memory map.
Recommandé
USB-to-Serial Communication Adapter
The AT90USB162-16MU can implement a compact USB-to-serial bridge by using its USB interface for host communication and its USART for a downstream serial link. The 16 MHz AVR core is suitable for framing, buffering, flow control, and command translation, while the 22 GPIO lines can expose status, reset, or configuration controls. The 512-byte SRAM supports short protocol buffers, and 512 bytes of EEPROM can retain calibration or configuration data. A production design must implement the USB class or vendor protocol, specify connector and I/O protection, and verify logic levels for the attached serial equipment.
Recommandé
Compact Industrial Data Acquisition
The AT90USB162-16MU suits a compact USB data-acquisition controller when the system needs local control, status, and configuration in addition to a host data link. Its 22 general-purpose I/O lines can interface with digital sensors, alarm inputs, and indicator circuits, while the USART and SPI can connect sensors or external converter ICs. The two timer/counters support timing, sampling control, and PWM functions. For industrial deployment, use an appropriate USB power and protection design, isolate external signal paths as required, and validate operating-temperature and EMC requirements for the complete assembly rather than the microcontroller alone.
Recommandé
USB Connected Test and Control Module
The AT90USB162-16MU can serve as the local controller in a USB-connected test fixture, programmable indicator, or bench accessory. Its 16 MHz processing capability supports command parsing and sequencing, and its GPIO, timers, USART, and SPI resources can drive relays, displays, measurement front ends, and external converters. The integrated USB interface removes a separate host-interface controller from a compact design. Firmware should include command validation, timing limits, and fault-safe outputs, while the PCB should maintain short return paths and isolate USB, digital, and analog sections to reduce susceptibility to ESD and ground-loop effects.
Recommandé
USB Motor and actuator Controller
The AT90USB162-16MU is suitable for a small USB-controlled actuator module that requires command handling and local sequencing. Timers with compare and PWM modes can generate motor-control or valve-timing signals, while the GPIO lines handle limit switches, enable inputs, and status feedback. The USB interface allows configuration and monitoring from a host computer, and the compact 32-VQFN package leaves room for driver and protection components. Designers must account for motor-current transients, maintain separation between noisy power paths and USB signals, and use appropriate protection on externally accessible motor and connector wiring.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour AT90USB162-16MU — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | AT90USB162-16AU | AT90USB162-16AUR | AT90USB162-16MU-KUMA | AT90USB162-16MUR | AT90USB82-16MU |
|---|---|---|---|---|---|---|
| Package | 32-VQFN (5 x 5 mm) | 32-VQFN (5 x 5 mm) | 32-VQFN (5 x 5 mm) | 32-VQFN (5 x 5 mm) | 32-VQFN (5 x 5 mm) | 32-VQFN (5 x 5 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Flash Memory | 16 KB (16K x 8) | 16 KB | 16 KB | 16 KB | 16 KB | 8 KB |
| Processor Architecture | 8-bit AVR-enhanced RISC | 8-bit AVR-enhanced RISC | 8-bit AVR-enhanced RISC | 8-bit AVR-enhanced RISC | 8-bit AVR-enhanced RISC | 8-bit AVR-enhanced RISC |
| Watchdog Timer | Programmable | Programmable | Programmable | Programmable | Programmable | Programmable |
Principaux différenciateurs
- Doubles the Flash capacity of the AT90USB82 family option (vs AT90USB82-16MU)
- Identical core resource level across AT90USB162 order-code alternatives (vs AT90USB162-16AU)
- Compact 32-VQFN implementation with integrated USB connectivity (vs AT90USB162-16AUR)
Notes de conception
Use the Microchip recommended 32-VQFN land pattern and verify it against the current package drawing before releasing the PCB. The exposed pad must be soldered and connected according to the datasheet, while the pad and perimeter leads should be inspected after reflow. Maintain the manufacturer-specified clearance around the package, place input and output bypass capacitors close to their pins, and provide a low-impedance ground reference for USB return current.
Route USB D+ and D- as a controlled-impedance differential pair over a continuous reference plane, with symmetrical geometry and minimal stubs. Keep the USB connector, protection devices, and MCU connection short, and avoid routing sensitive analog or timing signals beneath the pair. Follow the Microchip USB hardware guidance for series resistors, ESD protection, and branch placement, and test the completed board for signal integrity across the required cable and host configurations.
Do not interchange AT90USB162 ordering suffixes solely because they use the same 32-VQFN footprint. Verify the device grade, packing configuration, clock option, and operating-temperature requirements for the exact production MPN. If a design changes to AT90USB82-16MU, recheck firmware size because its 8 KB Flash is half the AT90USB162-16MU's 16 KB, and confirm USB peripheral compatibility rather than assuming register-level equivalence.
Calculate the complete board budget for USB bus-powered and self-powered operating modes, including the MCU, regulator, USB transceiver load, pull resistors, indicators, and external actuators. Use the current and quiescent values in the Microchip electrical-characteristics tables under the exact clock and peripheral conditions selected for the design. Confirm the regulator's startup behavior and voltage tolerance before enabling external loads through GPIO or power-control switches.
Informations de conformité
Exact compliance declarations for AT90USB162-16MU must be confirmed through Microchip's material-declaration resources. AEC-Q100 qualification cannot be inferred from the family name or package.