AT90USB162-16MU - 16MHz AVR USB MCU | Microchip Technology
MPN: AT90USB162-16MU ✓ Hoạt độngAT90USB162-16MU Tóm tắt
An 8-bit AVR microcontroller is a compact embedded processor intended for control-oriented products that coordinate peripherals, read sensors, update displays, and manage communication links. Its RISC-oriented instruction set, working registers, and dedicated peripheral modules place the AT90USB162 within the hierarchy of microcontrollers, embedded processors, and semiconductor control devices. The product is particularly relevant to USB-connected human-interface, communications, and compact embedded-control designs.
Key features include 16 KB of read-while-write ISP Flash, 512 bytes of EEPROM, and 512 bytes of SRAM. The device provides 22 general-purpose I/O lines and 32 general-purpose working registers. Two flexible timer/counters with compare modes and PWM, a USART, SPI, and a programmable watchdog timer support typical embedded-control duties. Its 16 MHz maximum clock speed provides approximately one MIPS-per-MHz-class execution capability for its AVR-enhanced RISC architecture.
The AT90USB162 architecture integrates USB interface hardware with an 8-bit AVR core, allowing a compact design to connect to a USB host without implementing a separate USB controller. ISP Flash supports in-system programming, while read-while-write operation allows nonvolatile code storage to remain useful during certain programming operations. The manufacturer describes the family as a low-power CMOS implementation combining 16 KB ISP Flash with 512-byte EEPROM and 512-byte SRAM.
Typical applications include USB human-interface devices, firmware update and bootloader equipment, USB-to-serial adapters, compact data-acquisition controllers, and industrial peripherals. The 22 I/O lines provide interfaces for buttons, indicators, sensors, and external transceivers, while the timers, USART, and SPI broaden its usefulness beyond a basic USB bridge. The 32-VQFN footprint is appropriate for compact USB accessories and embedded modules.
Board design requires careful attention to USB signal integrity, exposed-pad soldering, decoupling, and programming access. Place the USB traces according to the manufacturer reference layout, keep the exposed thermal pad soldered to the ground plane, and provide local bulk and high-frequency bypass capacitors close to the supply pins. Confirm the exact pin functions and alternate-pin assignments in the Microchip pin-description table before routing the PCB.
This page combines the AT90USB162 family specifications, package information, documented drop-in family alternatives, application guidance, and design-focused comparisons to help engineers evaluate USB MCU integration before schematic capture and PCB layout.
Bộ thay thế dễ dàng lắp đặt cho AT90USB162-16MU — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AT90USB162-16MU (cùng hình factor và footprint) — khác nhau ở Package, General-Purpose I/O Lines, General-Purpose Working Registers, Program Memory, Programming Interface.
AT90USB162-16AU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →AT90USB162-16AUR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AT90USB162-16MU-KUMA
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AT90USB162-16MUR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AT90USB82-16MU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →AT90USB162-16MU Tỷ lệ tối đa & tính chất điện
| Microcontroller Type | 8-bit AVR RISC-based microcontroller |
| Tần số xung maksimum | 16 MHz |
| Flash Memory | 16 KB (16K x 8) |
| EEPROM Memory | 512 bytes |
| SRAM | 512 bytes |
| General-Purpose I/O Lines | 22 |
| General-Purpose Working Registers | 32 |
| Architecture | AVR-enhanced RISC |
| Timer/Counter Count | 2 |
| Timer Features | Compare modes and PWM |
| Serial Interfaces | USART and SPI |
| Watchdog Timer | Programmable |
| Programming Interface | In-System Programming (ISP) |
| Read-While-Write Flash | Supported |
| Hộp | 32-VQFN, 5 x 5 mm |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân AT90USB162-16MU 32-vqfn, 5 x 5 mm
Cấu hình chân cho AT90USB162-16MU (32-vqfn, 5 x 5 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho AT90USB162-16MU.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AT90USB162-16MU phù hợp cho 6 Áp dụngs: USB Human-Interface Devices, USB Bootloader and Firmware Update, USB-to-Serial Communication Adapter, Compact Industrial Data Acquisition, USB Connected Test and Control Module, USB Motor and actuator Controller.
USB Human-Interface Devices
The AT90USB162-16MU fits a USB keyboard, control panel, game controller, or other human-interface device because it combines a 16 MHz AVR core with USB connectivity, 22 general-purpose I/O lines, and timers with PWM and compare modes. Buttons, LEDs, encoders, and status indicators can be connected through the GPIO and timer resources while the USB interface handles enumeration and data exchange. The 32-VQFN 5 x 5 mm package also allows a compact implementation. PCB design must preserve the manufacturer's USB trace geometry, provide local supply bypassing, and verify the selected crystal or clock configuration before firmware development.
Được đề xuất
USB Bootloader and Firmware Update
The AT90USB162-16MU is appropriate for USB-connected firmware update equipment because it combines 16 KB of read-while-write ISP Flash with an integrated USB interface and 512 bytes of EEPROM. A bootloader can occupy the protected boot section, detect an update request, exchange data over USB, and resume the application after validation. The 16 MHz operating speed provides useful execution throughput for protocol handling, while 22 GPIO lines can support recovery buttons, status LEDs, and boot-mode control. Designers should protect bootloader and application boundaries, follow the ISP programming sequence, and verify the exact Flash organization in the manufacturer memory map.
Được đề xuất
USB-to-Serial Communication Adapter
The AT90USB162-16MU can implement a compact USB-to-serial bridge by using its USB interface for host communication and its USART for a downstream serial link. The 16 MHz AVR core is suitable for framing, buffering, flow control, and command translation, while the 22 GPIO lines can expose status, reset, or configuration controls. The 512-byte SRAM supports short protocol buffers, and 512 bytes of EEPROM can retain calibration or configuration data. A production design must implement the USB class or vendor protocol, specify connector and I/O protection, and verify logic levels for the attached serial equipment.
Được đề xuất
Compact Industrial Data Acquisition
The AT90USB162-16MU suits a compact USB data-acquisition controller when the system needs local control, status, and configuration in addition to a host data link. Its 22 general-purpose I/O lines can interface with digital sensors, alarm inputs, and indicator circuits, while the USART and SPI can connect sensors or external converter ICs. The two timer/counters support timing, sampling control, and PWM functions. For industrial deployment, use an appropriate USB power and protection design, isolate external signal paths as required, and validate operating-temperature and EMC requirements for the complete assembly rather than the microcontroller alone.
Được đề xuất
USB Connected Test and Control Module
The AT90USB162-16MU can serve as the local controller in a USB-connected test fixture, programmable indicator, or bench accessory. Its 16 MHz processing capability supports command parsing and sequencing, and its GPIO, timers, USART, and SPI resources can drive relays, displays, measurement front ends, and external converters. The integrated USB interface removes a separate host-interface controller from a compact design. Firmware should include command validation, timing limits, and fault-safe outputs, while the PCB should maintain short return paths and isolate USB, digital, and analog sections to reduce susceptibility to ESD and ground-loop effects.
Được đề xuất
USB Motor and actuator Controller
The AT90USB162-16MU is suitable for a small USB-controlled actuator module that requires command handling and local sequencing. Timers with compare and PWM modes can generate motor-control or valve-timing signals, while the GPIO lines handle limit switches, enable inputs, and status feedback. The USB interface allows configuration and monitoring from a host computer, and the compact 32-VQFN package leaves room for driver and protection components. Designers must account for motor-current transients, maintain separation between noisy power paths and USB signals, and use appropriate protection on externally accessible motor and connector wiring.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AT90USB162-16MU — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AT90USB162-16AU | AT90USB162-16AUR | AT90USB162-16MU-KUMA | AT90USB162-16MUR | AT90USB82-16MU |
|---|---|---|---|---|---|---|
| Package | 32-VQFN (5 x 5 mm) | 32-VQFN (5 x 5 mm) | 32-VQFN (5 x 5 mm) | 32-VQFN (5 x 5 mm) | 32-VQFN (5 x 5 mm) | 32-VQFN (5 x 5 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Flash Memory | 16 KB (16K x 8) | 16 KB | 16 KB | 16 KB | 16 KB | 8 KB |
| Processor Architecture | 8-bit AVR-enhanced RISC | 8-bit AVR-enhanced RISC | 8-bit AVR-enhanced RISC | 8-bit AVR-enhanced RISC | 8-bit AVR-enhanced RISC | 8-bit AVR-enhanced RISC |
| Watchdog Timer | Programmable | Programmable | Programmable | Programmable | Programmable | Programmable |
Bảo phân biệt quan trọng
- Doubles the Flash capacity of the AT90USB82 family option (vsAT90USB82-16MU)
- Identical core resource level across AT90USB162 order-code alternatives (vsAT90USB162-16AU)
- Compact 32-VQFN implementation with integrated USB connectivity (vsAT90USB162-16AUR)
Ghi chú thiết kế
Use the Microchip recommended 32-VQFN land pattern and verify it against the current package drawing before releasing the PCB. The exposed pad must be soldered and connected according to the datasheet, while the pad and perimeter leads should be inspected after reflow. Maintain the manufacturer-specified clearance around the package, place input and output bypass capacitors close to their pins, and provide a low-impedance ground reference for USB return current.
Route USB D+ and D- as a controlled-impedance differential pair over a continuous reference plane, with symmetrical geometry and minimal stubs. Keep the USB connector, protection devices, and MCU connection short, and avoid routing sensitive analog or timing signals beneath the pair. Follow the Microchip USB hardware guidance for series resistors, ESD protection, and branch placement, and test the completed board for signal integrity across the required cable and host configurations.
Do not interchange AT90USB162 ordering suffixes solely because they use the same 32-VQFN footprint. Verify the device grade, packing configuration, clock option, and operating-temperature requirements for the exact production MPN. If a design changes to AT90USB82-16MU, recheck firmware size because its 8 KB Flash is half the AT90USB162-16MU's 16 KB, and confirm USB peripheral compatibility rather than assuming register-level equivalence.
Calculate the complete board budget for USB bus-powered and self-powered operating modes, including the MCU, regulator, USB transceiver load, pull resistors, indicators, and external actuators. Use the current and quiescent values in the Microchip electrical-characteristics tables under the exact clock and peripheral conditions selected for the design. Confirm the regulator's startup behavior and voltage tolerance before enabling external loads through GPIO or power-control switches.
Thông tin tuân thủ
Exact compliance declarations for AT90USB162-16MU must be confirmed through Microchip's material-declaration resources. AEC-Q100 qualification cannot be inferred from the family name or package.