ATF22LV10CQZ-30JC - 30ns 10-Macrocell EE PLD | Microchip
Référence : ATF22LV10CQZ-30JC ✓ ActifATF22LV10CQZ-30JC Présentation
A simple programmable logic device, or SPLD, is a user-programmable digital logic component within the broader programmable-logic-device and semiconductor hierarchy. It combines AND-array logic, programmable OR-array logic, input registers, and output registers into a compact device for implementing fixed control, decoding, interface, and glue-logic functions. Electrically erasable flash memory allows the configuration to be rewritten without removing the package from its circuit board.
The principal operating characteristics of the ATF22LV10CQZ-30JC include 10 macrocells, a 30 ns speed grade, operation from 3.0 V to 5.5 V, and a 28-pin PLCC package. The Microchip ATF22LV10CQZ family supports speeds down to 25 ns, and its edge-sensing circuitry can place the CQZ version into a zero standby-power mode when the device is idle. The manufacturer datasheet lists 3 uA typical standby current for the ATF22LV10CQZ version. These characteristics suit systems that need reconfigurable compact logic without using a larger FPGA or microcontroller.
The ATF22LV10C architecture uses 10 macrocells to implement sum-of-products combinational or registered logic functions. Registered outputs can be selected through the device programming configuration, allowing registered versus combinational behavior to be assigned on a macrocell basis. Input transition detection provides the low-power operating behavior associated with the CQZ family, while the pin-keeper feature helps retain input states when necessary. Configuration data is stored in electrically erasable flash memory for repeated in-circuit updates.
Typical uses include industrial control logic, peripheral decoding, bus-interface arbitration, data-format conversion, embedded timing sequences, and compact system-control functions. The 3.0 V minimum operating voltage supports low-voltage systems, while operation to 5.5 V provides design flexibility for mixed-voltage equipment. A 30 ns propagation-delay grade is appropriate for control paths that do not require the fastest 25 ns ATF22LV10CQZ option.
Designers should account for the PLCC footprint and verify the exact pin assignment, programming file, and power-down behavior before replacing an existing ATF22LV10CQZ-30JC. Because flash-programmed logic has setup, programming, and system-power requirements, use the manufacturer programming and application guidance rather than treating the device as a conventional mask-programmed PAL. Keep supply and ground connections compact and follow the datasheet decoupling recommendations.
This product summary combines the manufacturer electrical characteristics with distributor package data, usable replacement guidance, and application-focused design notes. It helps engineers identify the ATF22LV10CQZ-30JC as a 28-PLCC, 10-macrocell, 30 ns programmable logic option when planning upgrades, legacy-product maintenance, and reconfiguration of compact control logic.
Alternatives de remplacement direct pour ATF22LV10CQZ-30JC — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ATF22LV10CQZ-30JC (même facteur de forme et même empreinte) — différant par Device Type, Architecture, Package Type, Temperature Grade, Supply Voltage Range.
ATF22LV10CQZ-30JU
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →ATF22LV10CQZ-30JI
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →ATF22LV10CZ-25JI
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →ATF22LV10CZ-25JC
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →GAL22V10D-20LJNI
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATF22LV10CQZ-30JC Valeurs maximales et caractéristiques électriques
| Device Type | Simple programmable logic device (SPLD) |
| Programmable Technology | Electrically erasable flash memory |
| Macrocells | 10 macrocells |
| Logic Family | ATF22LV10CQZ |
| Speed Grade | 30 ns |
| Family Maximum Speed | 25 ns |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Standby Current | 3 uA typical |
| Power-Down Feature | Zero standby power-down mode |
| Input Transition Detection | Edge-sensing |
| Boîtier | 28-PLCC (11.51 mm x 11.51 mm) |
| Lead Count | 28 leads |
| Type de montage | Surface mount |
| Architecture | 10-macrocell CMOS SPLD |
| Configuration Memory | Electrically erasable flash |
| Industrial Temperature Version | ATF22LV10CQZ-30JI |
Configuration des broches de ATF22LV10CQZ-30JC
| Broche 1 | CLK — Dedicated clock input |
| Broche 2 | I7 — Dedicated input |
| Broche 3 | I6 — Dedicated input |
| Broche 4 | I5 — Dedicated input |
| Broche 5 | I4 — Dedicated input |
| Broche 6 | I3 — Dedicated input |
| Broche 7 | I2 — Dedicated input |
| Broche 8 | I1 — Dedicated input |
| Broche 9 | I0 — Dedicated input |
| Broche 10 | OE — Output enable |
| Broche 11 | GND — Ground |
| Broche 12 | PD — Power-down control |
| Broche 13 | IO7 — Input/output 7 |
| Broche 14 | IO6 — Input/output 6 |
| Broche 15 | IO5 — Input/output 5 |
| Broche 16 | IO4 — Input/output 4 |
| Broche 17 | IO3 — Input/output 3 |
| Broche 18 | IO2 — Input/output 2 |
| Broche 19 | IO1 — Input/output 1 |
| Broche 20 | IO0 — Input/output 0 |
| Broche 21 | VCC — Positive power supply |
| Broche 22 | A0 — Configuration address input 0 |
| Broche 23 | A1 — Configuration address input 1 |
| Broche 24 | A2 — Configuration address input 2 |
| Broche 25 | A3 — Configuration address input 3 |
| Broche 26 | A4 — Configuration address input 4 |
| Broche 27 | A5 — Configuration address input 5 |
| Broche 28 | A6 — Configuration address input 6 |
Applications typiques
ATF22LV10CQZ-30JC convient pour 6 applications: Industrial Control Logic, Peripheral Bus Interface, Data Format Conversion, Low-Power Embedded System, Instrumentation Signal Control, Legacy System Upgrade.
Industrial Control Logic
The ATF22LV10CQZ-30JC fits compact industrial control blocks requiring programmable decoding, latch functions, interlocks, and sequencing without the overhead of a larger FPGA. Its 10 macrocells provide a practical logic-building area, while the 30 ns grade supports control paths operating within the family timing limits. Electrically erasable flash permits configuration updates during maintenance or board rework. The 3.0 V to 5.5 V operating range supports 3.3 V and 5 V control rails, although the design must observe the exact timing, temperature, and power limits in the ATF22LV10C datasheet.
Recommandé
Peripheral Bus Interface
The ATF22LV10CQZ-30JC can implement address decoding, chip-select generation, bus arbitration, and data-routing logic around a legacy peripheral bus. Ten macrocells allow several related Boolean and registered functions to be consolidated in one 28-PLCC package. The 30 ns propagation-delay class should be checked against the combined address-decoder and control-path budget rather than treated as a complete system timing guarantee. Flash programmability also supports field updates when interface behavior changes, provided the original JEDEC fuse file is replaced with an equivalent validated configuration.
Recommandé
Data Format Conversion
The ATF22LV10CQZ-30JC is useful for compact parallel data-format conversion, bit-field routing, parity generation, and protocol-specific control logic. Its registered macrocell capability allows pipelines or synchronized outputs to be implemented where the application requires them. The 10-macrocell structure is best suited to defined combinational or shallow sequential functions rather than large data-path engines. At a 30 ns speed grade, external interface timing must include output-delay and setup requirements, while the 3.0 V to 5.5 V supply range provides flexibility across legacy 3.3 V and 5 V subsystems.
Recommandé
Low-Power Embedded System
The ATF22LV10CQZ-30JC supports low-power embedded systems because its edge-sensing CQZ implementation can enter a zero standby-power mode when the device is idle. The manufacturer lists 3 uA typical standby current for the ATF22LV10CQZ version, which is valuable for supervisory, sleep-state, and intermittently active control functions. Actual power consumption still depends on the number of active macrocells, switching activity, supply voltage, and power-down pin usage. Electrically erasable flash makes the logic field-configurable without removing the device from the assembly.
Recommandé
Instrumentation Signal Control
The ATF22LV10CQZ-30JC can implement deterministic control logic around sensors, measurement front ends, and actuator drivers in laboratory or industrial instrumentation. Typical functions include range selection, trigger routing, status encoding, and interlock generation. Because it is a digital SPLD rather than an analog signal-path component, it should control switches, dividers, and interface signals rather than process analog signals directly. The 30 ns speed and 10 macrocells suit compact control glue, while its reprogrammable flash configuration facilitates calibration of digital offsets and instrument-specific routing.
Recommandé
Legacy System Upgrade
The ATF22LV10CQZ-30JC is appropriate for maintaining or updating legacy programmable-logic systems that use the ATF22LV10 architecture and 28-PLCC footprint. Flash configuration allows revised logic to be programmed before installation and can simplify production changes compared with mask-programmed alternatives. Engineers should preserve the original logic assignment, verify every power and programming connection, and confirm that the replacement variant's temperature grade is adequate. The documented ATF22LV10CQZ-30JU and ATF22LV10CQZ-30JI options provide close same-family alternatives for qualification and lifecycle planning.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ATF22LV10CQZ-30JC — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ATF22LV10CQZ-30JU | ATF22LV10CQZ-30JI | ATF22LV10CZ-25JI | ATF22LV10CZ-25JC | GAL22V10D-20LJNI |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-PLCC (11.51 mm x 11.51 mm) | 28-PLCC family | 28-PLCC family | 28-LCC | 28-LCC | 28-LCC |
| Speed Grade | 30 ns | 30 ns | 30 ns | 25 ns | 25 ns | 20 ns |
| Macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells |
| Temperature Variant | Commercial JC ordering variant | JU ordering variant | Industrial-temperature JI variant | Industrial-temperature JI variant | Commercial JC variant | Industrial JNI ordering variant |
Principaux différenciateurs
- Exact same-speed same-family configuration (vs ATF22LV10CQZ-30JI)
- Faster timing option in the same ATF22LV10 family (vs ATF22LV10CZ-25JI)
- Zero-standby-power CQZ family behavior (vs GAL22V10D-20LJNI)
Notes de conception
Use the 28-PLCC land pattern and verify pin 1 orientation against the manufacturer package drawing before layout release. Keep the CLK, output-enable, power-down, and configuration-address routes away from noisy switching nodes, and place the device close to the signals it decodes or controls. Because the catalog library has no dedicated 28-PLCC key, the rendered package diagram uses the default library asset; PCB artwork must follow the official PLCC drawing rather than the generic diagram.
Follow the manufacturer supply and decoupling recommendations, including a low-impedance ground connection and the prescribed bypass capacitor placement. Treat the 3 uA typical value as an ATF22LV10CQZ standby figure, not an active-state consumption limit. When estimating dissipation, calculate active current from the datasheet operating conditions and use P = VIN × ICC, then add the power-down behavior only when the system actually invokes that mode.
Do not assume that all ATF22LV10C ordering variants are interchangeable without checking architecture, speed grade, temperature range, and package. The ATF22LV10CZ-25JI and ATF22LV10CZ-25JC options are faster than the 30 ns target, while the GAL22V10D-20LJNI candidate may use a different configuration or programming convention. Validate the JEDEC logic file, pin functions, timing assumptions, and power-down behavior before approving a substitute.
Informations de conformité
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was found for the exact MPN. The ATF22LV10CQZ-30JI is identified as an industrial-temperature variant, but industrial temperature grading does not establish AEC-Q100 qualification.