ATF22V10BQ-15SI - 10-Macrocell 15ns PLD | Microchip
Référence : ATF22V10BQ-15SI ✗ Fin de vieATF22V10BQ-15SI Présentation
A programmable logic device, or PLD, is a semiconductor whose digital logic behavior is defined by a user configuration rather than a fixed circuit. The ATF22V10B combines a compact 22V10 architecture, 10 macrocells and configurable I/O in the same package. Its position within the logic hierarchy—configurable PLD, digital logic IC and semiconductor—makes it useful for implementing compact control, decoding, multiplexing and interface logic without relying on a larger programmable device.
Key device characteristics include a 15 ns propagation-speed designation, 10 macrocells, electrically erasable Flash configuration memory and a 24-SOIC package. The ATF22V10B family is specified at a nominal 5 V supply, with the manufacturer documenting 5 V ±10% ranges for military and industrial temperature grades and 5 V ±5% for the relevant commercial range. These operating conditions make supply tolerance and logic-level compatibility central to implementation.
The electrically erasable architecture allows a device to be reconfigured without a dedicated programmer that erases only one-time-programmable cells. This supports design revisions, production programming and reusable control logic. However, the device is a simple PLD rather than a FPGA: its 10 macrocells are intended for compact combinational and registered logic, and complex system-level control is better handled by a programmable logic device with more resources.
Typical uses include industrial control interfaces, decoder and mux structures, pulse and timing qualification, alarm and interlock logic, test-fixture control and compact legacy system interfaces. The 24-pin SOIC package also makes the ATF22V10BQ-15SI suitable for designs requiring conventional surface-mount assembly rather than a large programmable-logic package.
Designers should verify supply tolerance, input thresholds, output drive, timing constraints and programming-device compatibility against the manufacturer datasheet before releasing a PCB. Decoupling and signal-integrity practices remain necessary even for a small PLD: place the supply capacitor close to the device, preserve the required clock and control routing, and use the package pin-definition table when assigning board signals.
This product record combines the device architecture, package characteristics, verified alternatives and application-oriented engineering guidance. It also identifies practical selection limits so engineers can distinguish a true same-footprint replacement from a PLD that is only functionally similar.
Alternatives de remplacement direct pour ATF22V10BQ-15SI — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ATF22V10BQ-15SI (même facteur de forme et même empreinte) — différant par Package, Speed Grade.
ATF22V10C-15SI
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATF22V10CQ-15SI
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATF22V10B-15SI
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATF22LV10C-10SU
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →ATF22V10BQ-15SC
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ATF22V10BQ-15SI Valeurs maximales et caractéristiques électriques
| Device Type | 22V10 electrically erasable CMOS programmable logic device |
| Macrocells | 10 macrocells |
| Speed Grade | 15 ns |
| Configuration Memory | Electrically erasable Flash memory |
| Nominal Supply Voltage | 5 V |
| Military and Industrial Supply Tolerance | 5 V ±10% |
| Commercial Supply Tolerance | 5 V ±5% |
| Boîtier | 24-SOIC |
| Package Body Width | 0.295 in (7.50 mm) |
| Nombre de broches | 24 pins |
| Type de montage | Surface mount |
| Logic Family | 22V10 |
| Programmable Device Type | Simple PLD |
| Process Technology | CMOS |
| Configuration Technology | Electrically erasable Flash memory |
| Statut RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Guide de configuration des broches du ATF22V10BQ-15SI 0.295 in (7.50 mm)
Configuration des broches du ATF22V10BQ-15SI (boîtier 0.295 in (7.50 mm)). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour ATF22V10BQ-15SI.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ATF22V10BQ-15SI convient pour 6 applications: Industrial Control Interlocks, Decoder and Multiplexer Logic, Pulse Qualification and Timing Control, Legacy System Interface Control, Test Fixture and Measurement Control, Alarm and Annunciator Logic.
Industrial Control Interlocks
The ATF22V10BQ-15SI fits compact industrial interlock logic where a 10-macrocell PLD can combine permissive conditions, fault latches and output decoding without a larger FPGA. Its 24-SOIC package simplifies rework and density compared with a larger programmable-logic package. The 15 ns speed grade provides a defined timing class for ordinary control paths, while the nominal 5 V supply matches legacy 5 V logic systems. Designers should verify every input threshold and output timing path against the ATF22V10B datasheet, especially for safety-related signals.
Recommandé
Decoder and Multiplexer Logic
The ATF22V10BQ-15SI is suitable for address decoding, command multiplexing and data-routing logic in compact control systems. Ten macrocells provide enough capacity for multiple registered and combinational equations without introducing an FPGA's configuration and resource overhead. The device's electrically erasable Flash configuration permits late design revisions, and its 15 ns grade simplifies timing analysis for moderate-speed control paths. The 24-SOIC footprint is useful where a standardized small-outline package is preferred.
Recommandé
Pulse Qualification and Timing Control
A 15 ns ATF22V10BQ-15SI can implement pulse-width qualification, event sequencing and deterministic timing windows when the required paths remain within the device's documented timing limits. Its 10 macrocells allow several timing channels to be combined, while programmable input and output assignments can reduce the number of discrete gates. Engineers should account for setup and hold requirements, output transitions and the selected propagation mode. Because the device is not a hard real-time microcontroller, critical timing margins must be calculated rather than assumed.
Recommandé
Legacy System Interface Control
The ATF22V10BQ-15SI can bridge older parallel command interfaces to modern control logic by implementing address decode, handshake generation, status multiplexing and interrupt request logic. Its 24-SOIC package is attractive for compact legacy boards because it avoids requiring a large FPGA package. The electrically erasable configuration supports engineering changes without replacing the physical device. Pin assignments must be reviewed carefully because programmable PLD pins can change function according to the fuse map and architecture.
Recommandé
Test Fixture and Measurement Control
The ATF22V10BQ-15SI is useful in test fixtures for generating control sequences, coordinating measurement steps and combining instrument-ready signals. Ten macrocells can handle compact sequencing logic while the 15 ns timing class supports ordinary fixture control rates. The small 24-SOIC package simplifies insertion into dense fixture boards, and Flash-based configuration allows firmware-like updates when test requirements change. Engineers should isolate long external lines and noisy relay or driver circuits to prevent fixture transients from exceeding device input limits.
Recommandé
Alarm and Annunciator Logic
The ATF22V10BQ-15SI can implement alarm prioritization, debounce logic, latched fault reporting and output-annunciator selection in equipment control systems. Its 10 macrocells allow several related alarm equations to be consolidated, while the 15 ns grade supports deterministic signal propagation in normal control paths. The 24-SOIC package is practical for compact boards and existing industrial spare-part designs. Validate each alarm path, including lockout, reset and fail-safe requirements, because software or peripheral logic must preserve the intended behavior during configuration changes.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ATF22V10BQ-15SI — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ATF22V10C-15SI | ATF22V10CQ-15SI | ATF22V10B-15SI | ATF22LV10C-10SU | ATF22V10BQ-15SC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 24-SOIC | 24-SOIC | 24-SOIC | 24-SOIC | 24-SOIC | 24-SOIC |
| Macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells |
| Speed Designation | 15 ns | 15 ns; family supports speeds down to 5 ns | 15 ns | 15 ns | 10 ns | 15 ns |
| Programmable Logic Type | 22V10 simple PLD | 22V10 simple PLD | 22V10 simple PLD | 22V10 simple PLD | 22V10-family simple PLD | 22V10 simple PLD |
| Nominal Supply Voltage | 5 V | 5 V | 5 V | 5 V | Low-voltage family; exact operating range requires datasheet review | 5 V |
| Pin Count | 24 pins | 24 pins | 24 pins | 24 pins | 24 pins | 24 pins |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Principaux différenciateurs
- 15 ns timing designation in a compact 10-macrocell PLD (vs ATF22LV10C-10SU)
- Direct 22V10 family alignment (vs ATF22V10CQ-15SI)
- Electrically erasable Flash configuration (vs ATF22V10C-15SI)
- Established nominal 5 V operating class (vs ATF22LV10C-10SU)
Notes de conception
Use the 24-SOIC land pattern specified by the Microchip package drawing rather than creating a footprint from body width alone. Confirm pad length, pad spacing and courtyard against the PCB fabrication rules. Keep the device orientation consistent with pin 1 marking, and route all 24 package positions even when the selected PLD configuration does not use every external function.
Place the required supply-decoupling capacitor close to the device's power pin and return it directly to the ground plane or ground reference. Follow the capacitor value and placement guidance in the ATF22V10B datasheet. Because the PLD operates from a nominal 5 V rail, verify that the minimum and maximum supply at the device remains inside the applicable grade's range during transient and power-up conditions.
Programmable-logic inputs may be sensitive to ringing, crosstalk and slow edges even when the maximum clock rate appears modest. Keep clocks and critical paths short, provide a continuous return path and avoid routing programmable inputs next to switching nodes. If an external line is long or noisy, add an appropriate receiver or filtering stage rather than relying on the PLD's internal logic to reject excessive transients.
Do not assume that two devices with the same 24-SOIC outline are automatically interchangeable. Before approving a drop-in candidate, compare pin functions, supply range, speed grade, temperature grade, output modes, power-up behavior and the fuse-map architecture. A candidate may share the footprint while requiring a different programmer configuration or having different I/O characteristics.
Informations de conformité
No explicit environmental or material-compliance declaration was identified for the exact ordering code. AEC-Q100 is marked not applicable because the ATF22V10BQ-15SI is a programmable logic device rather than an automotive-qualified component in the available records.