ATF22V10BQ-15SI - 10-Macrocell 15ns PLD | Microchip
MPN: ATF22V10BQ-15SI ✗ जीवन की समाप्तिATF22V10BQ-15SI अवलोकन
A programmable logic device, or PLD, is a semiconductor whose digital logic behavior is defined by a user configuration rather than a fixed circuit. The ATF22V10B combines a compact 22V10 architecture, 10 macrocells and configurable I/O in the same package. Its position within the logic hierarchy—configurable PLD, digital logic IC and semiconductor—makes it useful for implementing compact control, decoding, multiplexing and interface logic without relying on a larger programmable device.
Key device characteristics include a 15 ns propagation-speed designation, 10 macrocells, electrically erasable Flash configuration memory and a 24-SOIC package. The ATF22V10B family is specified at a nominal 5 V supply, with the manufacturer documenting 5 V ±10% ranges for military and industrial temperature grades and 5 V ±5% for the relevant commercial range. These operating conditions make supply tolerance and logic-level compatibility central to implementation.
The electrically erasable architecture allows a device to be reconfigured without a dedicated programmer that erases only one-time-programmable cells. This supports design revisions, production programming and reusable control logic. However, the device is a simple PLD rather than a FPGA: its 10 macrocells are intended for compact combinational and registered logic, and complex system-level control is better handled by a programmable logic device with more resources.
Typical uses include industrial control interfaces, decoder and mux structures, pulse and timing qualification, alarm and interlock logic, test-fixture control and compact legacy system interfaces. The 24-pin SOIC package also makes the ATF22V10BQ-15SI suitable for designs requiring conventional surface-mount assembly rather than a large programmable-logic package.
Designers should verify supply tolerance, input thresholds, output drive, timing constraints and programming-device compatibility against the manufacturer datasheet before releasing a PCB. Decoupling and signal-integrity practices remain necessary even for a small PLD: place the supply capacitor close to the device, preserve the required clock and control routing, and use the package pin-definition table when assigning board signals.
This product record combines the device architecture, package characteristics, verified alternatives and application-oriented engineering guidance. It also identifies practical selection limits so engineers can distinguish a true same-footprint replacement from a PLD that is only functionally similar.
के लिए ड्रॉप-इन विकल्प ATF22V10BQ-15SI — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं ATF22V10BQ-15SI (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Speed Grade.
ATF22V10C-15SI
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ATF22V10CQ-15SI
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ATF22V10B-15SI
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ATF22LV10C-10SU
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →ATF22V10BQ-15SC
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
ATF22V10BQ-15SI Maximum Ratings और Electrical Characteristics
| Device Type | 22V10 electrically erasable CMOS programmable logic device |
| Macrocells | 10 macrocells |
| Speed Grade | 15 ns |
| Configuration Memory | Electrically erasable Flash memory |
| Nominal Supply Voltage | 5 V |
| Military and Industrial Supply Tolerance | 5 V ±10% |
| Commercial Supply Tolerance | 5 V ±5% |
| पैकेज | 24-SOIC |
| Package Body Width | 0.295 in (7.50 mm) |
| पिन काउंट | 24 pins |
| माउंटिंग प्रकार | Surface mount |
| Logic Family | 22V10 |
| Programmable Device Type | Simple PLD |
| Process Technology | CMOS |
| Configuration Technology | Electrically erasable Flash memory |
| RoHS स्थिति | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
ATF22V10BQ-15SI 0.295 in (7.50 mm) पिन कॉन्फ़िगरेशन गाइड
ATF22V10BQ-15SI (0.295 in (7.50 mm) पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस डिजिटल IC में GPIO, संचार इंटरफ़ेस (UART, SPI, I2C) और पावर पिन शामिल हैं। वैकल्पिक पिन फ़ंक्शन और कॉन्फ़िगरेशन विकल्पों के लिए निर्माता डेटाशीट देखें। एम्बेडेड सिस्टम डिज़ाइन और PCB लेआउट के लिए आवश्यक।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: ATF22V10BQ-15SI.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
ATF22V10BQ-15SI के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Control Interlocks, Decoder and Multiplexer Logic, Pulse Qualification and Timing Control, Legacy System Interface Control, Test Fixture and Measurement Control, Alarm and Annunciator Logic.
Industrial Control Interlocks
The ATF22V10BQ-15SI fits compact industrial interlock logic where a 10-macrocell PLD can combine permissive conditions, fault latches and output decoding without a larger FPGA. Its 24-SOIC package simplifies rework and density compared with a larger programmable-logic package. The 15 ns speed grade provides a defined timing class for ordinary control paths, while the nominal 5 V supply matches legacy 5 V logic systems. Designers should verify every input threshold and output timing path against the ATF22V10B datasheet, especially for safety-related signals.
अनुशंसित
Decoder and Multiplexer Logic
The ATF22V10BQ-15SI is suitable for address decoding, command multiplexing and data-routing logic in compact control systems. Ten macrocells provide enough capacity for multiple registered and combinational equations without introducing an FPGA's configuration and resource overhead. The device's electrically erasable Flash configuration permits late design revisions, and its 15 ns grade simplifies timing analysis for moderate-speed control paths. The 24-SOIC footprint is useful where a standardized small-outline package is preferred.
अनुशंसित
Pulse Qualification and Timing Control
A 15 ns ATF22V10BQ-15SI can implement pulse-width qualification, event sequencing and deterministic timing windows when the required paths remain within the device's documented timing limits. Its 10 macrocells allow several timing channels to be combined, while programmable input and output assignments can reduce the number of discrete gates. Engineers should account for setup and hold requirements, output transitions and the selected propagation mode. Because the device is not a hard real-time microcontroller, critical timing margins must be calculated rather than assumed.
अनुशंसित
Legacy System Interface Control
The ATF22V10BQ-15SI can bridge older parallel command interfaces to modern control logic by implementing address decode, handshake generation, status multiplexing and interrupt request logic. Its 24-SOIC package is attractive for compact legacy boards because it avoids requiring a large FPGA package. The electrically erasable configuration supports engineering changes without replacing the physical device. Pin assignments must be reviewed carefully because programmable PLD pins can change function according to the fuse map and architecture.
अनुशंसित
Test Fixture and Measurement Control
The ATF22V10BQ-15SI is useful in test fixtures for generating control sequences, coordinating measurement steps and combining instrument-ready signals. Ten macrocells can handle compact sequencing logic while the 15 ns timing class supports ordinary fixture control rates. The small 24-SOIC package simplifies insertion into dense fixture boards, and Flash-based configuration allows firmware-like updates when test requirements change. Engineers should isolate long external lines and noisy relay or driver circuits to prevent fixture transients from exceeding device input limits.
अनुशंसित
Alarm and Annunciator Logic
The ATF22V10BQ-15SI can implement alarm prioritization, debounce logic, latched fault reporting and output-annunciator selection in equipment control systems. Its 10 macrocells allow several related alarm equations to be consolidated, while the 15 ns grade supports deterministic signal propagation in normal control paths. The 24-SOIC package is practical for compact boards and existing industrial spare-part designs. Validate each alarm path, including lockout, reset and fail-safe requirements, because software or peripheral logic must preserve the intended behavior during configuration changes.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा ATF22V10BQ-15SI — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | ATF22V10C-15SI | ATF22V10CQ-15SI | ATF22V10B-15SI | ATF22LV10C-10SU | ATF22V10BQ-15SC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 24-SOIC | 24-SOIC | 24-SOIC | 24-SOIC | 24-SOIC | 24-SOIC |
| Macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells |
| Speed Designation | 15 ns | 15 ns; family supports speeds down to 5 ns | 15 ns | 15 ns | 10 ns | 15 ns |
| Programmable Logic Type | 22V10 simple PLD | 22V10 simple PLD | 22V10 simple PLD | 22V10 simple PLD | 22V10-family simple PLD | 22V10 simple PLD |
| Nominal Supply Voltage | 5 V | 5 V | 5 V | 5 V | Low-voltage family; exact operating range requires datasheet review | 5 V |
| Pin Count | 24 pins | 24 pins | 24 pins | 24 pins | 24 pins | 24 pins |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
मुख्य विशेषताएँ
- 15 ns timing designation in a compact 10-macrocell PLD (बनामATF22LV10C-10SU)
- Direct 22V10 family alignment (बनामATF22V10CQ-15SI)
- Electrically erasable Flash configuration (बनामATF22V10C-15SI)
- Established nominal 5 V operating class (बनामATF22LV10C-10SU)
डिज़ाइन नोट्स
Use the 24-SOIC land pattern specified by the Microchip package drawing rather than creating a footprint from body width alone. Confirm pad length, pad spacing and courtyard against the PCB fabrication rules. Keep the device orientation consistent with pin 1 marking, and route all 24 package positions even when the selected PLD configuration does not use every external function.
Place the required supply-decoupling capacitor close to the device's power pin and return it directly to the ground plane or ground reference. Follow the capacitor value and placement guidance in the ATF22V10B datasheet. Because the PLD operates from a nominal 5 V rail, verify that the minimum and maximum supply at the device remains inside the applicable grade's range during transient and power-up conditions.
Programmable-logic inputs may be sensitive to ringing, crosstalk and slow edges even when the maximum clock rate appears modest. Keep clocks and critical paths short, provide a continuous return path and avoid routing programmable inputs next to switching nodes. If an external line is long or noisy, add an appropriate receiver or filtering stage rather than relying on the PLD's internal logic to reject excessive transients.
Do not assume that two devices with the same 24-SOIC outline are automatically interchangeable. Before approving a drop-in candidate, compare pin functions, supply range, speed grade, temperature grade, output modes, power-up behavior and the fuse-map architecture. A candidate may share the footprint while requiring a different programmer configuration or having different I/O characteristics.
अनुपालन जानकारी
No explicit environmental or material-compliance declaration was identified for the exact ordering code. AEC-Q100 is marked not applicable because the ATF22V10BQ-15SI is a programmable logic device rather than an automotive-qualified component in the available records.