ATF22V10BQ-15SI - 10-Macrocell 15ns PLD | Microchip
MPN: ATF22V10BQ-15SI ✗ Cuối đờiATF22V10BQ-15SI Tóm tắt
A programmable logic device, or PLD, is a semiconductor whose digital logic behavior is defined by a user configuration rather than a fixed circuit. The ATF22V10B combines a compact 22V10 architecture, 10 macrocells and configurable I/O in the same package. Its position within the logic hierarchy—configurable PLD, digital logic IC and semiconductor—makes it useful for implementing compact control, decoding, multiplexing and interface logic without relying on a larger programmable device.
Key device characteristics include a 15 ns propagation-speed designation, 10 macrocells, electrically erasable Flash configuration memory and a 24-SOIC package. The ATF22V10B family is specified at a nominal 5 V supply, with the manufacturer documenting 5 V ±10% ranges for military and industrial temperature grades and 5 V ±5% for the relevant commercial range. These operating conditions make supply tolerance and logic-level compatibility central to implementation.
The electrically erasable architecture allows a device to be reconfigured without a dedicated programmer that erases only one-time-programmable cells. This supports design revisions, production programming and reusable control logic. However, the device is a simple PLD rather than a FPGA: its 10 macrocells are intended for compact combinational and registered logic, and complex system-level control is better handled by a programmable logic device with more resources.
Typical uses include industrial control interfaces, decoder and mux structures, pulse and timing qualification, alarm and interlock logic, test-fixture control and compact legacy system interfaces. The 24-pin SOIC package also makes the ATF22V10BQ-15SI suitable for designs requiring conventional surface-mount assembly rather than a large programmable-logic package.
Designers should verify supply tolerance, input thresholds, output drive, timing constraints and programming-device compatibility against the manufacturer datasheet before releasing a PCB. Decoupling and signal-integrity practices remain necessary even for a small PLD: place the supply capacitor close to the device, preserve the required clock and control routing, and use the package pin-definition table when assigning board signals.
This product record combines the device architecture, package characteristics, verified alternatives and application-oriented engineering guidance. It also identifies practical selection limits so engineers can distinguish a true same-footprint replacement from a PLD that is only functionally similar.
Bộ thay thế dễ dàng lắp đặt cho ATF22V10BQ-15SI — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATF22V10BQ-15SI (cùng hình factor và footprint) — khác nhau ở Package, Speed Grade.
ATF22V10C-15SI
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATF22V10CQ-15SI
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATF22V10B-15SI
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATF22LV10C-10SU
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATF22V10BQ-15SC
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATF22V10BQ-15SI Tỷ lệ tối đa & tính chất điện
| Device Type | 22V10 electrically erasable CMOS programmable logic device |
| Macrocells | 10 macrocells |
| Speed Grade | 15 ns |
| Configuration Memory | Electrically erasable Flash memory |
| Nominal Supply Voltage | 5 V |
| Military and Industrial Supply Tolerance | 5 V ±10% |
| Commercial Supply Tolerance | 5 V ±5% |
| Hộp | 24-SOIC |
| Package Body Width | 0.295 in (7.50 mm) |
| Số chân | 24 pins |
| Kiểu lắp đặt | Surface mount |
| Logic Family | 22V10 |
| Programmable Device Type | Simple PLD |
| Process Technology | CMOS |
| Configuration Technology | Electrically erasable Flash memory |
| Trạng thái RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Hướng dẫn cấu hình chân ATF22V10BQ-15SI 0.295 in (7.50 mm)
Cấu hình chân cho ATF22V10BQ-15SI (0.295 in (7.50 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho ATF22V10BQ-15SI.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ATF22V10BQ-15SI phù hợp cho 6 Áp dụngs: Industrial Control Interlocks, Decoder and Multiplexer Logic, Pulse Qualification and Timing Control, Legacy System Interface Control, Test Fixture and Measurement Control, Alarm and Annunciator Logic.
Industrial Control Interlocks
The ATF22V10BQ-15SI fits compact industrial interlock logic where a 10-macrocell PLD can combine permissive conditions, fault latches and output decoding without a larger FPGA. Its 24-SOIC package simplifies rework and density compared with a larger programmable-logic package. The 15 ns speed grade provides a defined timing class for ordinary control paths, while the nominal 5 V supply matches legacy 5 V logic systems. Designers should verify every input threshold and output timing path against the ATF22V10B datasheet, especially for safety-related signals.
Được đề xuất
Decoder and Multiplexer Logic
The ATF22V10BQ-15SI is suitable for address decoding, command multiplexing and data-routing logic in compact control systems. Ten macrocells provide enough capacity for multiple registered and combinational equations without introducing an FPGA's configuration and resource overhead. The device's electrically erasable Flash configuration permits late design revisions, and its 15 ns grade simplifies timing analysis for moderate-speed control paths. The 24-SOIC footprint is useful where a standardized small-outline package is preferred.
Được đề xuất
Pulse Qualification and Timing Control
A 15 ns ATF22V10BQ-15SI can implement pulse-width qualification, event sequencing and deterministic timing windows when the required paths remain within the device's documented timing limits. Its 10 macrocells allow several timing channels to be combined, while programmable input and output assignments can reduce the number of discrete gates. Engineers should account for setup and hold requirements, output transitions and the selected propagation mode. Because the device is not a hard real-time microcontroller, critical timing margins must be calculated rather than assumed.
Được đề xuất
Legacy System Interface Control
The ATF22V10BQ-15SI can bridge older parallel command interfaces to modern control logic by implementing address decode, handshake generation, status multiplexing and interrupt request logic. Its 24-SOIC package is attractive for compact legacy boards because it avoids requiring a large FPGA package. The electrically erasable configuration supports engineering changes without replacing the physical device. Pin assignments must be reviewed carefully because programmable PLD pins can change function according to the fuse map and architecture.
Được đề xuất
Test Fixture and Measurement Control
The ATF22V10BQ-15SI is useful in test fixtures for generating control sequences, coordinating measurement steps and combining instrument-ready signals. Ten macrocells can handle compact sequencing logic while the 15 ns timing class supports ordinary fixture control rates. The small 24-SOIC package simplifies insertion into dense fixture boards, and Flash-based configuration allows firmware-like updates when test requirements change. Engineers should isolate long external lines and noisy relay or driver circuits to prevent fixture transients from exceeding device input limits.
Được đề xuất
Alarm and Annunciator Logic
The ATF22V10BQ-15SI can implement alarm prioritization, debounce logic, latched fault reporting and output-annunciator selection in equipment control systems. Its 10 macrocells allow several related alarm equations to be consolidated, while the 15 ns grade supports deterministic signal propagation in normal control paths. The 24-SOIC package is practical for compact boards and existing industrial spare-part designs. Validate each alarm path, including lockout, reset and fail-safe requirements, because software or peripheral logic must preserve the intended behavior during configuration changes.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATF22V10BQ-15SI — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATF22V10C-15SI | ATF22V10CQ-15SI | ATF22V10B-15SI | ATF22LV10C-10SU | ATF22V10BQ-15SC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 24-SOIC | 24-SOIC | 24-SOIC | 24-SOIC | 24-SOIC | 24-SOIC |
| Macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells |
| Speed Designation | 15 ns | 15 ns; family supports speeds down to 5 ns | 15 ns | 15 ns | 10 ns | 15 ns |
| Programmable Logic Type | 22V10 simple PLD | 22V10 simple PLD | 22V10 simple PLD | 22V10 simple PLD | 22V10-family simple PLD | 22V10 simple PLD |
| Nominal Supply Voltage | 5 V | 5 V | 5 V | 5 V | Low-voltage family; exact operating range requires datasheet review | 5 V |
| Pin Count | 24 pins | 24 pins | 24 pins | 24 pins | 24 pins | 24 pins |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Bảo phân biệt quan trọng
- 15 ns timing designation in a compact 10-macrocell PLD (vsATF22LV10C-10SU)
- Direct 22V10 family alignment (vsATF22V10CQ-15SI)
- Electrically erasable Flash configuration (vsATF22V10C-15SI)
- Established nominal 5 V operating class (vsATF22LV10C-10SU)
Ghi chú thiết kế
Use the 24-SOIC land pattern specified by the Microchip package drawing rather than creating a footprint from body width alone. Confirm pad length, pad spacing and courtyard against the PCB fabrication rules. Keep the device orientation consistent with pin 1 marking, and route all 24 package positions even when the selected PLD configuration does not use every external function.
Place the required supply-decoupling capacitor close to the device's power pin and return it directly to the ground plane or ground reference. Follow the capacitor value and placement guidance in the ATF22V10B datasheet. Because the PLD operates from a nominal 5 V rail, verify that the minimum and maximum supply at the device remains inside the applicable grade's range during transient and power-up conditions.
Programmable-logic inputs may be sensitive to ringing, crosstalk and slow edges even when the maximum clock rate appears modest. Keep clocks and critical paths short, provide a continuous return path and avoid routing programmable inputs next to switching nodes. If an external line is long or noisy, add an appropriate receiver or filtering stage rather than relying on the PLD's internal logic to reject excessive transients.
Do not assume that two devices with the same 24-SOIC outline are automatically interchangeable. Before approving a drop-in candidate, compare pin functions, supply range, speed grade, temperature grade, output modes, power-up behavior and the fuse-map architecture. A candidate may share the footprint while requiring a different programmer configuration or having different I/O characteristics.
Thông tin tuân thủ
No explicit environmental or material-compliance declaration was identified for the exact ordering code. AEC-Q100 is marked not applicable because the ATF22V10BQ-15SI is a programmable logic device rather than an automotive-qualified component in the available records.