Microchip Technology

ATTINY861A-PU - 8-bit 20MHz AVR MCU | Microchip Technology

Référence : ATTINY861A-PU ✓ Actif
20-pin DIP Package 20 MHz Speed 8 KB Memory
MOQ : 1 |

ATTINY861A-PU Présentation

Microchip Technology ATTINY861A-PU is an 8-bit AVR RISC-based microcontroller with 8 KB of in-system programmable Flash memory, 512 bytes of EEPROM, 512 bytes of SRAM, and 16 general-purpose I/O lines. It operates up to 20 MHz and is packaged in a 20-pin DIP. The ATTINY861A combines a compact embedded-control architecture with a low-power picoPower design.

An 8-bit AVR microcontroller is a programmable semiconductor that integrates a CPU core, program memory, data memory, I/O ports, timers, and communication peripherals on one chip. Within the Microchip product hierarchy, ATtiny861A belongs to the tinyAVR family of 8-bit RISC microcontrollers, which are designed for compact control tasks, low-power operation, and cost-sensitive embedded products.

Key features include 8 KB of Flash for firmware, 512 bytes of EEPROM for nonvolatile data, 512 bytes of SRAM, 16 general-purpose I/O lines, and 32 general-purpose working registers. The manufacturer describes an 8-bit timer/counter with compare modes and an AVR instruction set with Harvard architecture. Its operating resources make it suitable for compact controllers that need more general-purpose I/O than very small 8-pin devices.

The ATTINY861A uses a separate program-memory and data-memory organization. Firmware occupies the in-system programmable Flash array, while SRAM supports working variables and stack operations. EEPROM retains calibration, configuration, counters, or user settings when power is removed. The 20 MHz maximum clock rate provides sufficient execution bandwidth for digital control, signal generation, timing, and low-speed serial-interface tasks.

Typical uses include compact sensor controllers, LED lighting and dimming modules, small appliance controls, educational automation projects, hobby robotics, simple keypad interfaces, and standalone battery-powered instruments. Designers can use the 16 I/O lines for switches, displays, sensors, actuators, and serial communications without requiring a larger system-on-chip package.

For a new 20-pin DIP layout, preserve the ATtiny861A pin assignments and provide the required power, ground, decoupling, programming, and reset connections described in the manufacturer datasheet. Check every peripheral pin against the selected fuse and clock configuration, and route programming-test or ISP signals away from sensitive analog inputs to reduce coupling.

This product page combines the manufacturer specifications with package guidance, application-oriented design notes, and a practical comparison of documented family alternatives. It focuses on helping engineers evaluate memory, I/O, timing, and tooling requirements before assigning the microcontroller to an embedded-control board.

Alternatives de remplacement direct pour ATTINY861A-PU — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

ATTINY461A-PU

✅ Remplacement direct
Microchip Technology
📦 20-pin DIP
8-bit AVR RISC-based microcontroller · 20 MHz · 4 KB (2K x 16) · 256 bytes · 256 bytes · 16 lines · 32 registers · 8-bit with compare modes

Contactez-nous pour le prix

Voir la fiche technique →

ATTINY261A-PU

✅ Remplacement direct
Microchip Technology
📦 20-pin DIP
8-bit AVR RISC-based microcontroller · 20 MHz · 2 KB (1K × 16 words) · 128 B · 128 B · 16 · 32 · 8-bit with compare modes

Contactez-nous pour le prix

Voir la fiche technique →

ATTINY861A-PU Valeurs maximales et caractéristiques électriques

Product Type 8-bit RISC microcontroller
Architecture AVR
Series tinyAVR
Fréquence d'horloge maximale 20 MHz
Flash Memory 8 KB
Flash Organization 4K x 16 bits
EEPROM 512 bytes
SRAM 512 bytes
General-Purpose I/O Lines 16
General-Purpose Working Registers 32
Timer/Counter 8-bit with compare modes
Boîtier 20-pin DIP
Package Pitch 7.62 mm
Package Body Width 0.300 inch
Type de montage Through-hole
Programming In-system programmable Flash

Configuration des broches de ATTINY861A-PU

DIP-20 Package Pinout Diagram DIP-20 20-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 DIP-20
Broche 1 PB0 — Port B general-purpose I/O pin 0
Broche 2 PB1 — Port B general-purpose I/O pin 1
Broche 3 PB2 — Port B general-purpose I/O pin 2
Broche 4 PB3 — Port B general-purpose I/O pin 3
Broche 5 PB4 — Port B general-purpose I/O pin 4
Broche 6 GND — Ground connection
Broche 7 PA6 — Port A general-purpose I/O pin 6
Broche 8 PA7 — Port A general-purpose I/O pin 7
Broche 9 PC7 — Port C general-purpose I/O pin 7
Broche 10 PC6 — Port C general-purpose I/O pin 6
Broche 11 PC5 — Port C general-purpose I/O pin 5
Broche 12 PC4 — Port C general-purpose I/O pin 4
Broche 13 PC3 — Port C general-purpose I/O pin 3
Broche 14 PC2 — Port C general-purpose I/O pin 2
Broche 15 PC1 — Port C general-purpose I/O pin 1
Broche 16 PC0 — Port C general-purpose I/O pin 0
Broche 17 PA3 — Port A general-purpose I/O pin 3
Broche 18 PA4 — Port A general-purpose I/O pin 4
Broche 19 PA5 — Port A general-purpose I/O pin 5
Broche 20 PA2/AVCC — Port A general-purpose I/O pin 2 and analog supply connection

Applications typiques

ATTINY861A-PU convient pour 6 applications: Low-Power Sensor Controller, LED Lighting and Dimming, Small Appliance Control, Educational Robotics Controller, Battery-Powered Instrument, Simple Communications Module.

🧩

Low-Power Sensor Controller

ATTINY861A-PU fits a compact sensor node because it combines 16 general-purpose I/O lines, 512 bytes of EEPROM, and an 8-bit AVR core operating up to 20 MHz. The I/O pins can connect switches, sensors, indicators, and an external transceiver without requiring a larger microcontroller package. Its 512 bytes of SRAM and 8 KB of Flash provide room for sampling logic and nonvolatile configuration, although the application must stay within those fixed memory budgets. For battery-powered operation, the firmware should use an appropriate sleep mode, disable unused peripherals, and select the lowest clock frequency that preserves required timing accuracy.

💡

LED Lighting and Dimming

ATTINY861A-PU is suitable for programmable LED lighting and dimming modules where multiple outputs require independent timing or switching control. Its 16 general-purpose I/O lines can drive LED indicators, logic-level transistor gates, or driver-control signals, while the 8-bit timer/counter with compare modes supports periodic events and timing functions. The 8 KB Flash can hold lighting tables, fade algorithms, and communication handling, while 512 bytes of EEPROM can retain brightness levels or scene selections. Validate the PWM method, output drive current, and switching-device dissipation against the specific LED driver rather than driving load current directly from the microcontroller.

🏭

Small Appliance Control

ATTINY861A-PU can serve as the central controller in a small appliance where a keypad, status indicators, sensor inputs, and an actuator interface must share one compact processor. Its 20 MHz AVR core supports responsive debouncing, state-machine execution, and periodic control tasks, while 16 I/O lines provide practical connectivity for external modules. The 8 KB Flash accommodates application firmware and lookup tables, and the 512-byte EEPROM preserves settings across power cycles. Designers should include appropriate isolation, flyback protection, and transistor drivers for inductive or high-voltage loads.

🔧

Educational Robotics Controller

ATTINY861A-PU works well as an educational robotics controller because it exposes 16 I/O lines while retaining enough Flash for motion logic, sensor fusion, and simple communication routines. The 20 MHz AVR architecture offers straightforward register-level interfacing for common classroom peripherals, and 512 bytes of EEPROM allows calibration values to survive resets. Its 20-pin DIP package is also convenient for breadboard and through-hole prototype construction. For motor control, use external driver circuitry and keep high-current switching paths away from sensitive input traces; the microcontroller should command the driver rather than carry motor current.

📱

Battery-Powered Instrument

ATTINY861A-PU is appropriate for a compact battery-powered instrument that records operating parameters and presents status through a small display or indicator set. The 8 KB Flash can store firmware and compact lookup data, while 512 bytes of EEPROM preserves user settings and calibration constants between sessions. Sixteen I/O lines are sufficient for a display interface, buttons, a measurement input, and a serial link. Because this device does not integrate a high-resolution analog converter, analog measurements require suitable external circuitry; the controller then performs scaling, control, and data handling after the conditioned signal reaches a supported peripheral input.

🌐

Simple Communications Module

ATTINY861A-PU can manage a compact communications module that needs protocol formatting, status reporting, and limited local configuration. The AVR core running up to 20 MHz can service byte- or bit-oriented serial tasks, while 16 I/O lines provide hardware handshaking, interrupt inputs, and user controls. Its 8 KB Flash supports a protocol stack and command interpreter, and 512 bytes of EEPROM can retain addresses, calibration, or operating modes. The designer must confirm peripheral timing, interrupt behavior, and logic levels for the selected communication interface before relying on it for a throughput-critical protocol.

What are the key specifications of ATTINY861A-PU?
The ATTINY861A-PU is an 8-bit AVR microcontroller rated up to 20 MHz with 8 KB of Flash, 512 bytes of EEPROM, 512 bytes of SRAM, and 16 general-purpose I/O lines in a 20-pin DIP package. According to the Microchip manufacturer product page, it also provides 32 general-purpose working registers and an 8-bit timer/counter with compare modes. These resources make it appropriate for compact embedded controllers that need more I/O and program storage than the smallest tinyAVR devices.
What is the operating voltage of ATTINY861A-PU?
The ATTINY861A-PU operates from the voltage range specified in the Microchip manufacturer datasheet, which should be checked against the exact clock, fuse, and peripheral configuration used in the design. The manufacturer product page confirms that the device is an 8-bit AVR microcontroller with 8 KB of Flash, 512 bytes of EEPROM, and 16 I/O lines. Use the datasheet's electrical-characteristics table to set decoupling, input thresholds, and programming-tool voltage levels.
Where can I download the ATTINY861A datasheet PDF?
The ATTINY861A datasheet PDF is available from Microchip through the official device-document link listed on this page, while the ATtiny861A family datasheet also appears in the verified document results. The manufacturer document covers the ATtiny261, ATtiny461, and ATtiny861 family. Use the family datasheet's pin description, electrical characteristics, memory, timer, and peripheral sections together with the package drawing for ATTINY861A-PU.
Where is the ATTINY861A pinout?
The ATTINY861A-PU uses a 20-pin DIP pinout with pin 1 adjacent to the package notch. According to the Microchip family datasheet, the pins include PB0 through PB4, GND, PA2 through PA7, PC0 through PC7, AVCC, and VCC. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks because some port pins also provide alternate peripheral functions.
Can ATTINY861A-PU be used with Arduino?
The ATTINY861A-PU can be used in Arduino-compatible projects when the board, bootloader, and programming procedure support its 20-pin DIP pinout and AVR toolchain. The manufacturer identifies the device as an AVR-based tinyAVR controller with 8 KB of Flash and 16 I/O lines. Because the Arduino ecosystem commonly centers on ATmega328P, confirm the boot section, fuse settings, ISP connection, and pin mapping before treating ATTINY861A-PU as a direct controller substitute.
What is ATTINY861A-PU used for?
ATTINY861A-PU is used for compact embedded-control tasks such as sensor interfaces, LED controllers, small appliance controls, timing modules, and simple communications equipment. The Microchip manufacturer page confirms 8 KB of Flash, 512 bytes of EEPROM, 512 bytes of SRAM, and 16 general-purpose I/O lines. Its 20 MHz AVR core and mix of digital I/O make it useful when a product needs more general-purpose connections than an 8-pin controller.
Where can I buy ATTINY861A-PU online?
Use the Request a Quote form on this page to request ATTINY861A-PU availability, current lead time, and order details. The product is listed by Microchip Technology in a 20-pin DIP package with 8 KB Flash, 512 bytes of EEPROM, 512 bytes of SRAM, and 16 I/O lines. Submit the required quantity and packaging information so the request can be matched to the exact ATTINY861A-PU ordering code.
What is the current price of ATTINY861A-PU?
Submit the ATTINY861A-PU quantity and application details through the Request a Quote form on this page for current commercial terms. The verified product information identifies the exact MPN as an 8-bit, 20 MHz AVR microcontroller with 8 KB Flash, 512 bytes EEPROM, 512 bytes SRAM, and 16 I/O lines in a 20-pin DIP. This avoids presenting a transient listing figure as a stable quotation.
Is ATTINY861A-PU in stock and what is its lead time?
Current stock and lead time for ATTINY861A-PU should be requested through the Request a Quote form on this page. The verified listing describes the component as a 20-pin DIP AVR device with 8 KB of Flash, 512 bytes of EEPROM, and 16 I/O lines, but inventory changes continuously. Provide the required quantity, production schedule, and packaging preference with the request.
What is the difference between ATTINY861A-PU and ATTINY461A-PU?
The principal documented distinction is Flash capacity: ATTINY861A-PU has 8 KB of Flash, while ATTINY461A-PU belongs to the lower-memory member of the same tinyAVR family. Both are 20-pin, 8-bit AVR devices intended for embedded control, but software built for the 8 KB part should be size-checked before using the 4 KB alternative. Review the family datasheet and verify all peripheral and fuse requirements before replacement.
Is ATTINY461A-PU a drop-in replacement for ATTINY861A-PU?
ATTINY461A-PU is pin-compatible at the family level, but it should not be treated as an unqualified drop-in replacement because its Flash memory is smaller than the 8 KB available in ATTINY861A-PU. The Microchip migration documentation identifies ATtiny461A as part of the compatible ATtiny261A/461A/861A family. Verify application size, bootloader layout, timing assumptions, and every peripheral use before substituting the lower-memory device.
What is the best drop-in replacement for ATTINY861A-PU?
The closest documented same-family candidate is ATTINY461A-PU because both use a 20-pin DIP arrangement and share the tinyAVR compatibility family described by Microchip. It is not an unrestricted drop-in match because its lower Flash capacity can invalidate existing firmware. ATTINY261A-PU is another related family member with still less Flash. No cross-brand, 20-pin DIP replacement was established as pin-to-pin and parametrically equivalent.
When should I choose ATTINY861A-PU over ATTINY461A-PU?
Choose ATTINY861A-PU when firmware, boot code, or future feature expansion requires the full 8 KB Flash allocation. Choose ATTINY461A-PU only after confirming that the application fits its smaller memory and that its electrical, timer, and peripheral characteristics meet the design. According to the Microchip family documentation, the ATtiny261A, ATtiny461A, and ATtiny861A devices share a compatible subfamily structure, but memory capacity remains a critical selection boundary.
Is ATTINY861A-PU suitable for a low-power sensor controller?
ATTINY861A-PU is suitable for a low-power sensor controller when the design uses its sleep modes efficiently and does not require a larger on-chip memory footprint. The Microchip manufacturer page identifies the device as a picoPower 8-bit AVR controller with 512 bytes of EEPROM for retained parameters and 16 I/O lines for sensors and control signals. The final battery-life result depends on the selected clock source, sleep mode, sensor duty cycle, and regulator quiescent current.
What programming tools can configure ATTINY861A-PU?
ATTINY861A-PU can be programmed through an AVR-compatible ISP interface using the programming tools and connector arrangement defined by the manufacturer datasheet. The device uses in-system programmable Flash and retains 512 bytes of EEPROM for nonvolatile data. Confirm the programming voltage, fuse settings, clock source, and ISP pin mapping on the target board before production programming to avoid incorrect lock-bit or clock configuration.

Données de référence d'ingénierie pour ATTINY861A-PU — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose ATTINY861A-PU when the firmware needs the full 8 KB of Flash, 512 bytes of SRAM, and 512 bytes of EEPROM while retaining 16 general-purpose I/O lines in a 20-pin DIP package. It is the preferred choice for moderately complex control firmware, retained configuration, and prototypes that may later require additional features. ATTINY461A-PU is a pin-compatible same-family option when 4 KB of Flash and 256 bytes of SRAM are sufficient. ATTINY261A-PU is appropriate only for substantially smaller programs because it provides 2 KB of Flash, 128 bytes of SRAM, and 128 bytes of EEPROM. Verify the selected device’s peripherals, clock requirements, fuse configuration, programming arrangement, and operating limits before finalizing a replacement. No cross-brand drop-in candidate was established with the same 20-pin DIP footprint and equivalent memory, I/O, timing, and peripheral requirements.

Comparaison avec les alternatives

Paramètre Ce produit ATTINY461A-PU ATTINY261A-PU
Package 20-pin DIP 20-pin DIP 20-pin DIP
Brand Microchip Technology Microchip Technology Microchip Technology
CPU Architecture 8-bit AVR RISC 8-bit AVR RISC 8-bit AVR RISC
Maximum Clock Frequency 20 MHz 20 MHz 20 MHz
Flash Memory 8 KB 4 KB 2 KB
EEPROM 512 bytes 512 bytes 128 bytes
SRAM 512 bytes 256 bytes 128 bytes
General-Purpose I/O Lines 16 16 16
General-Purpose Working Registers 32 32 32
Timer/Counter 8-bit with compare modes 8-bit with compare modes 8-bit with compare modes
Programming In-system programmable Flash In-system programmable Flash In-system programmable Flash
Product Family tinyAVR tinyAVR tinyAVR

Principaux différenciateurs

  • Twice the Flash memory of ATTINY461A-PU (vs ATTINY461A-PU)
  • Four times the Flash memory of ATTINY261A-PU (vs ATTINY261A-PU)
  • More SRAM for working data and stack (vs ATTINY461A-PU)
  • Retains the same 16-pin I/O count in a 20-pin DIP footprint (vs ATTINY461A-PU)

Notes de conception

Place the required supply bypass capacitors close to the VCC and AVCC pins, following the capacitor values and placement shown in the Microchip family datasheet. Separate analog and digital supply paths where the analog subsystem is used, and keep the AVCC connection clean. Verify that the regulator can supply the combined digital and analog load without excessive ripple during GPIO switching.

Reserve the ISP programming signals and RESET access on the PCB so the firmware can be programmed and recovered after assembly. Route clock, programming, and high-speed switching nets away from sensitive analog inputs. Because the device is a 20-pin DIP, maintain a 7.62 mm pin pitch and provide adequate clearance around the socket or through-hole pads for soldering and rework.

Do not substitute ATTINY461A-PU or ATTINY261A-PU without checking firmware size and retained-data requirements. Their 4 KB and 2 KB Flash capacities are respectively 50% and 75% below the ATTINY861A-PU's 8 KB capacity, and their smaller SRAM can also affect stack and buffer sizing. Rebuild and verify the image for the selected memory configuration before programming.

Assign unused pins according to the manufacturer pin-description table and terminate unused communications inputs so they cannot float during reset. Confirm ISP and reset functions, port multiplexing, and analog input selection before finalizing the schematic. A short ground-return path and locally placed decoupling components are especially important when the DIP device is used on a long prototyping board.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

No definitive environmental or automotive qualification statements were identified for the exact ATTINY861A-PU ordering code. Verify compliance with the manufacturer product documentation or a current declaration before release.

Données vérifiées le : 2026-11-14 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

attiny861a datasheet attiny861a pinout attiny861a microcontroller attiny861a arduino microcontrolador attiny861a ATTINY861A-PU datasheet pdf ATTINY861A-PU pinout ATTINY861A-PU equivalent ATTINY861A-PU replacement ATTINY861A-PU vs ATTINY461A-PU Microchip ATTINY861A-PU ATTINY861A-PU price ATTINY861A-PU stock ATTINY861A 20MHz 8KB Flash ATTINY861A-PU application circuit

Composants & termes associés

Microchip Technology ATTINY861A-PU ATtiny861A ATTINY461A-PU ATTINY261A-PU AVR tinyAVR 8-bit RISC microcontroller embedded controller semiconductor In-system programming ISP 8 KB Flash 512-byte EEPROM 512-byte SRAM 20 MHz 16 general-purpose I/O lines 8-bit timer/counter 20-pin DIP 7.62 mm DIP picoPower RoHS REACH AEC-Q100
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ