DG213DJ - 4-Channel 60 Ohm CMOS Analog Switch | Vishay
Référence : DG213DJ ✗ Fin de vieDG213DJ Présentation
An analog switch is an integrated semiconductor device that connects or disconnects an analog signal path under digital control. Unlike a mechanical relay, it can change state rapidly without mechanical wear. The DG213DJ belongs to the analog switch, interface IC, and semiconductor hierarchy. Its CMOS implementation provides low leakage, while the 1:1 circuit configuration routes one source path to one switched output without changing the signal polarity.
Key features include a 22 V supply-voltage rating, 45 ohm low on-resistance, TTL-compatible and CMOS-compatible control logic, and 20 pA low leakage. The design supports both dual-supply operation up to ±22 V and single-rail operation up to 36 V. A continuous current rating of 30 mA makes the device appropriate for instrumentation and general-purpose analog routing rather than high-current power switching. The improved charge-injection compensation helps reduce switching transients in sensitive measurement circuits.
The DG213DJ uses a complementary CMOS switch architecture optimized for general-purpose signal isolation. Its low leakage limits unwanted disturbance on high-impedance nodes, while the specified 85 ns turn-on time supports reasonably fast control-response requirements. An epitaxial layer is used to reduce latch-up risk, and the low on-resistance limits signal attenuation when the switch is closed. Designers should still evaluate channel capacitance, charge injection, and off-isolation across the intended operating bandwidth.
Typical applications include sample-and-hold systems, test and measurement equipment, process-control interfaces, telecommunications equipment, and computer peripherals. The device can route test, sensor, or control signals to a shared amplifier or converter. In precision systems, its low leakage and charge-injection compensation help preserve small-signal integrity, while its TTL-compatible control inputs simplify connection to legacy digital logic.
A primary design consideration is ensuring that the control input levels meet the device's logic thresholds and that supply and signal voltages remain within the specified operating range. Place bypass capacitors close to the supply pins and route high-impedance signal traces away from switching-control and supply-return paths. Check absolute maximum ratings when switching signals that may exceed the nominal supply range.
This page combines the manufacturer's electrical characteristics with lifecycle information, drop-in replacement analysis, application guidance, and package-specific design considerations. It helps engineers evaluate the DG213DJ for signal-routing designs, identify lifecycle risks, and plan source transitions without overlooking analog performance constraints.
Alternatives de remplacement direct pour DG213DJ — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
DG213DJ-E3
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MAX4603EPE+
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DG213DJ Valeurs maximales et caractéristiques électriques
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 SPST-NO/NC |
| Architecture | Complementary CMOS analog switch |
| Rated On-Resistance | 60 ohm |
| Low On-Resistance | 45 ohm |
| Low Leakage | 20 pA |
| Turn-On Time | 85 ns |
| Supply Voltage Rating | 22 V |
| Dual-Supply Signal Handling | Up to ±22 V |
| Single-Supply Signal Handling | Up to 36 V |
| Continuous Current Rating | 30 mA |
| Logic Compatibility | TTL and CMOS compatible |
| Latch-Up Protection | Epitaxial layer |
| Boîtier | 16-pin PDIP |
| Type de montage | Through-hole |
| Statut du cycle de vie | Obsolete |
Guide de configuration des broches du DG213DJ 16-pin pdip
Configuration des broches du DG213DJ (boîtier 16-pin pdip). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour DG213DJ.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
DG213DJ convient pour 6 applications: Precision Instrumentation Signal Routing, Sample-and-Hold Signal Paths, Process-Control Signal Isolation, Telecommunications Signal Routing, Computer-Peripheral Interfacing, Test and Measurement Equipment.
Precision Instrumentation Signal Routing
The DG213DJ suits precision instrumentation because its four 1:1 switch channels provide 60 ohm rated on-resistance, 20 pA leakage, and charge-injection compensation for reducing switching transients. Place the device between a sensor or test input and the measuring amplifier, then use separate control signals to isolate channels. Its 85 ns turn-on time supports responsive selection, although the 30 mA continuous current limit means it should not be used as a power relay.
Sample-and-Hold Signal Paths
The DG213DJ can route acquisition inputs into a sample-and-hold or measurement front end through its four complementary CMOS channels. Low 20 pA leakage helps preserve charge at high-impedance sampling nodes, while the 1:1 configuration avoids signal inversion. Confirm acquisition time, channel capacitance, and control overlap in the system timing, and use the improved charge-injection compensation as a starting point rather than assuming zero switching error.
Process-Control Signal Isolation
The DG213DJ is appropriate for process-control systems that must route several low-level control or sensor signals while isolating inactive channels. Its 20 pA leakage reduces unwanted coupling into high-impedance inputs, and its 60 ohm on-resistance is suitable for many instrumentation paths. The extended switching function also supports signals up to ±22 V under dual-supply operation, although each signal must remain within the complete electrical-characteristic table.
Telecommunications Signal Routing
In telecommunications equipment, the DG213DJ can multiplex or isolate lines feeding measurement, conversion, or monitoring circuits. The four independent 1:1 channels, 85 ns turn-on time, and TTL-compatible control logic simplify interface with digital control systems. Its continuous current rating of 30 mA is adequate for signal routing but not for load switching, so designers should verify input levels, off-isolation, and bandwidth for each line.
Computer-Peripheral Interfacing
The DG213DJ fits general-purpose computer-peripheral interfaces that require fast, low-leakage analog routing between functional blocks. It can connect an external line to an internal converter or measurement amplifier without mechanical switching delay. The 16-pin PDIP package supports through-hole boards, and the 85 ns turn-on time is adequate for moderate-speed control paths. Check supply sequencing and ensure logic thresholds remain valid during startup.
Test and Measurement Equipment
The DG213DJ can route test signals among input, output, and reference sections in automated test equipment. Four channels reduce the number of discrete routing elements, while 20 pA leakage and compensated charge injection help protect precision measurements. Its 85 ns switching time supports moderate-speed test sequencing, but system settling must include the time required for the connected source and measurement network to respond.
Données de référence d'ingénierie pour DG213DJ — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DG213DJ-E3 | MAX4603EPE+ |
|---|---|---|---|
| Brand | Vishay Intertechnology | Vishay Intertechnology | Maxim Integrated |
| Package | 16-PDIP | 16-PDIP - same package | 16-PDIP - same package |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 1:1 SPST-NO/NC | 1:1 SPST-NO/NC | 1:1 |
| Maximum Voltage | ±22 V dual supply; 36 V single rail | ±22 V dual supply; 36 V single rail | 30 V maximum |
Principaux différenciateurs
- Higher dual-supply signal capability than the MAX4603EPE+ alternative (vs MAX4603EPE+)
- Complete four-channel complementary CMOS routing in one DIP (vs MAX4603EPE+)
- Closest same-manufacturer ordering configuration (vs MAX4603EPE+)
Notes de conception
Treat the 30 mA continuous current rating as a firm design boundary and use the DG213DJ for analog signal routing rather than power-load switching. Also keep supply, signal, and absolute-maximum voltages within the datasheet limits; the ability to handle signals up to ±22 V with dual supplies does not permit every supply combination. Check the switching-state tables before connecting external circuitry.
For high-impedance measurement nodes, minimize leakage paths and evaluate charge injection at the actual control-driver voltage and source impedance. The DG213DJ specifies 20 pA leakage and uses improved charge-injection compensation, but external leakage, PCB contamination, cable capacitance, and control-edge coupling can dominate the total error. Keep sensitive traces short and use guarding or guarding techniques where practical.
Place the bypass capacitors close to the supply and ground pins, provide a low-impedance return path, and route control traces away from high-impedance analog inputs. Through-hole DIP construction can make long analog traces more susceptible to coupling than a compact surface-mount implementation. Use a ground plane where practical and place the device near the switched source to minimize parasitic capacitance.
Informations de conformité
The DG213DJ is a general-purpose analog switch rather than an automotive-qualified device. No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified.