DG213DJ - 4-Channel 60 Ohm CMOS Analog Switch | Vishay
部品番号: DG213DJ ✗ 生産終了DG213DJ 概要
An analog switch is an integrated semiconductor device that connects or disconnects an analog signal path under digital control. Unlike a mechanical relay, it can change state rapidly without mechanical wear. The DG213DJ belongs to the analog switch, interface IC, and semiconductor hierarchy. Its CMOS implementation provides low leakage, while the 1:1 circuit configuration routes one source path to one switched output without changing the signal polarity.
Key features include a 22 V supply-voltage rating, 45 ohm low on-resistance, TTL-compatible and CMOS-compatible control logic, and 20 pA low leakage. The design supports both dual-supply operation up to ±22 V and single-rail operation up to 36 V. A continuous current rating of 30 mA makes the device appropriate for instrumentation and general-purpose analog routing rather than high-current power switching. The improved charge-injection compensation helps reduce switching transients in sensitive measurement circuits.
The DG213DJ uses a complementary CMOS switch architecture optimized for general-purpose signal isolation. Its low leakage limits unwanted disturbance on high-impedance nodes, while the specified 85 ns turn-on time supports reasonably fast control-response requirements. An epitaxial layer is used to reduce latch-up risk, and the low on-resistance limits signal attenuation when the switch is closed. Designers should still evaluate channel capacitance, charge injection, and off-isolation across the intended operating bandwidth.
Typical applications include sample-and-hold systems, test and measurement equipment, process-control interfaces, telecommunications equipment, and computer peripherals. The device can route test, sensor, or control signals to a shared amplifier or converter. In precision systems, its low leakage and charge-injection compensation help preserve small-signal integrity, while its TTL-compatible control inputs simplify connection to legacy digital logic.
A primary design consideration is ensuring that the control input levels meet the device's logic thresholds and that supply and signal voltages remain within the specified operating range. Place bypass capacitors close to the supply pins and route high-impedance signal traces away from switching-control and supply-return paths. Check absolute maximum ratings when switching signals that may exceed the nominal supply range.
This page combines the manufacturer's electrical characteristics with lifecycle information, drop-in replacement analysis, application guidance, and package-specific design considerations. It helps engineers evaluate the DG213DJ for signal-routing designs, identify lifecycle risks, and plan source transitions without overlooking analog performance constraints.
ドロップイン代替品: DG213DJ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
DG213DJ-E3
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MAX4603EPE+
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DG213DJ 最大定格&電気的特性
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 SPST-NO/NC |
| Architecture | Complementary CMOS analog switch |
| Rated On-Resistance | 60 ohm |
| Low On-Resistance | 45 ohm |
| Low Leakage | 20 pA |
| Turn-On Time | 85 ns |
| Supply Voltage Rating | 22 V |
| Dual-Supply Signal Handling | Up to ±22 V |
| Single-Supply Signal Handling | Up to 36 V |
| Continuous Current Rating | 30 mA |
| Logic Compatibility | TTL and CMOS compatible |
| Latch-Up Protection | Epitaxial layer |
| パッケージ | 16-pin PDIP |
| 実装タイプ | Through-hole |
| ライフサイクル状態 | Obsolete |
DG213DJ 16-pin pdip ピン配置ガイド
DG213DJ (16-pin pdip パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: DG213DJ.
詳細は データシート をご参照ください。
主な用途
DG213DJ の用途: 6 件s: Precision Instrumentation Signal Routing, Sample-and-Hold Signal Paths, Process-Control Signal Isolation, Telecommunications Signal Routing, Computer-Peripheral Interfacing, Test and Measurement Equipment.
Precision Instrumentation Signal Routing
The DG213DJ suits precision instrumentation because its four 1:1 switch channels provide 60 ohm rated on-resistance, 20 pA leakage, and charge-injection compensation for reducing switching transients. Place the device between a sensor or test input and the measuring amplifier, then use separate control signals to isolate channels. Its 85 ns turn-on time supports responsive selection, although the 30 mA continuous current limit means it should not be used as a power relay.
Sample-and-Hold Signal Paths
The DG213DJ can route acquisition inputs into a sample-and-hold or measurement front end through its four complementary CMOS channels. Low 20 pA leakage helps preserve charge at high-impedance sampling nodes, while the 1:1 configuration avoids signal inversion. Confirm acquisition time, channel capacitance, and control overlap in the system timing, and use the improved charge-injection compensation as a starting point rather than assuming zero switching error.
Process-Control Signal Isolation
The DG213DJ is appropriate for process-control systems that must route several low-level control or sensor signals while isolating inactive channels. Its 20 pA leakage reduces unwanted coupling into high-impedance inputs, and its 60 ohm on-resistance is suitable for many instrumentation paths. The extended switching function also supports signals up to ±22 V under dual-supply operation, although each signal must remain within the complete electrical-characteristic table.
Telecommunications Signal Routing
In telecommunications equipment, the DG213DJ can multiplex or isolate lines feeding measurement, conversion, or monitoring circuits. The four independent 1:1 channels, 85 ns turn-on time, and TTL-compatible control logic simplify interface with digital control systems. Its continuous current rating of 30 mA is adequate for signal routing but not for load switching, so designers should verify input levels, off-isolation, and bandwidth for each line.
Computer-Peripheral Interfacing
The DG213DJ fits general-purpose computer-peripheral interfaces that require fast, low-leakage analog routing between functional blocks. It can connect an external line to an internal converter or measurement amplifier without mechanical switching delay. The 16-pin PDIP package supports through-hole boards, and the 85 ns turn-on time is adequate for moderate-speed control paths. Check supply sequencing and ensure logic thresholds remain valid during startup.
Test and Measurement Equipment
The DG213DJ can route test signals among input, output, and reference sections in automated test equipment. Four channels reduce the number of discrete routing elements, while 20 pA leakage and compensated charge injection help protect precision measurements. Its 85 ns switching time supports moderate-speed test sequencing, but system settling must include the time required for the connected source and measurement network to respond.
エンジニアリング参考データ: DG213DJ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DG213DJ-E3 | MAX4603EPE+ |
|---|---|---|---|
| Brand | Vishay Intertechnology | Vishay Intertechnology | Maxim Integrated |
| Package | 16-PDIP | 16-PDIP - same package | 16-PDIP - same package |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 1:1 SPST-NO/NC | 1:1 SPST-NO/NC | 1:1 |
| Maximum Voltage | ±22 V dual supply; 36 V single rail | ±22 V dual supply; 36 V single rail | 30 V maximum |
主な差別化要因
- Higher dual-supply signal capability than the MAX4603EPE+ alternative (vs MAX4603EPE+)
- Complete four-channel complementary CMOS routing in one DIP (vs MAX4603EPE+)
- Closest same-manufacturer ordering configuration (vs MAX4603EPE+)
設計ノート
Treat the 30 mA continuous current rating as a firm design boundary and use the DG213DJ for analog signal routing rather than power-load switching. Also keep supply, signal, and absolute-maximum voltages within the datasheet limits; the ability to handle signals up to ±22 V with dual supplies does not permit every supply combination. Check the switching-state tables before connecting external circuitry.
For high-impedance measurement nodes, minimize leakage paths and evaluate charge injection at the actual control-driver voltage and source impedance. The DG213DJ specifies 20 pA leakage and uses improved charge-injection compensation, but external leakage, PCB contamination, cable capacitance, and control-edge coupling can dominate the total error. Keep sensitive traces short and use guarding or guarding techniques where practical.
Place the bypass capacitors close to the supply and ground pins, provide a low-impedance return path, and route control traces away from high-impedance analog inputs. Through-hole DIP construction can make long analog traces more susceptible to coupling than a compact surface-mount implementation. Use a ground plane where practical and place the device near the switched source to minimize parasitic capacitance.
コンプライアンス情報
The DG213DJ is a general-purpose analog switch rather than an automotive-qualified device. No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified.