DS90CF364AMTDX - 18-Bit 65MHz LVDS Receiver | Texas Instruments
Référence : DS90CF364AMTDX ✓ ActifDS90CF364AMTDX Présentation
An LVDS receiver is an interface integrated circuit that converts low-voltage differential signaling into a logic-level digital signal. LVDS belongs to the broader differential-interface hierarchy and is commonly used where reliable data transfer, low electromagnetic interference, and scalable clock rates are important. The DS90CF364A family targets flat-panel-display links connecting a transmitter or display source to a receiver endpoint.
The key operating characteristics are a 3.3 V supply, an 18-bit FPD link, and a maximum signaling frequency of 65 MHz. The 48-pin TSSOP package provides a conventional surface-mount footprint suitable for multilayer PCB designs. The operating-temperature range shown on the manufacturer part-details page is -10 °C to 70 °C, making the device appropriate for commercial and industrial equipment with controlled ambient conditions.
The receiver architecture is intended to recover data from LVDS differential pairs and present compatible parallel digital signals to the connected display system. Its 65 MHz signaling rate establishes the timing envelope for the associated data lanes, while the 18-bit interface supports parallel display-related information. Designers must preserve controlled-impedance routing between the transmitter and receiver, maintain the required input termination, and observe the voltage and timing constraints defined by the manufacturer.
Typical uses include flat-panel display controllers, industrial display equipment, video timing interfaces, monitor electronics, and embedded human-machine-interface systems. In these applications, the DS90CF364AMTDX can serve as the receiving endpoint for an LVDS FPD link, reducing susceptibility to common-mode noise when compared with a single-ended transfer path.
PCB implementation should provide continuous ground planes, short differential traces, matched pair lengths, and proper LVDS input termination. The receiver should be placed according to the package and datasheet layout guidance, with supply decoupling and signal-return paths arranged to minimize switching noise. Component substitutions should be checked for identical pin functions, supply requirements, clock capability, and electrical timing rather than package name alone.
This product page combines the manufacturer's ordering information, interface specifications, package details, drop-in replacement references, application guidance, and a parameter-by-parameter comparison. It is intended to help engineers identify the correct receiver and verify PCB, timing, thermal, and sourcing constraints before committing a design to production.
Alternatives de remplacement direct pour DS90CF364AMTDX — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
DS90CF364MTDX/NOPB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DS90CF364AMTDX/NOPB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DS90CF364AMTDX Spécifications
| Product Type | LVDS FPD Receiver |
| Tension d'alimentation | 3.3 V |
| Interface Width | 18 bits |
| Maximum Signaling Frequency | 65 MHz |
| Logic Standard | LVDS |
| Application | Flat Panel Display Link |
| Boîtier | 48-pin TSSOP (DGG) |
| Nombre de broches | 48 pins |
| Type de montage | Surface Mount |
| Plage de température de fonctionnement | -10 °C to 70 °C |
Guide de configuration des broches du DS90CF364AMTDX 48-pin tssop (dgg)
Configuration des broches du DS90CF364AMTDX (boîtier 48-pin tssop (dgg)). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour DS90CF364AMTDX.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
DS90CF364AMTDX convient pour 6 applications: Industrial Flat-Panel Display Receiver, Monitor Electronics, Video Timing Interface, Human-Machine Interface Display, Embedded Display Controller, Digital Signage Interface.
Industrial Flat-Panel Display Receiver
The DS90CF364AMTDX fits the receiving end of an industrial flat-panel display link because it accepts an 18-bit differential FPD interface at up to 65 MHz using a 3.3 V supply. It can terminate an LVDS link from a display controller and present parallel data to downstream timing or pixel-processing circuitry. The differential receiver architecture is valuable around motors, switching supplies, and long internal cables where common-mode noise could affect a single-ended interface. Engineers should preserve controlled-impedance routing, terminate each LVDS pair as specified, and verify the transmitter's lane mapping against the DS90CF364A pin table.
Recommandé
Monitor Electronics
The DS90CF364AMTDX is suitable for monitor electronics requiring a dedicated receiver for an 18-bit LVDS display link at 65 MHz. The receiver can connect a video timing controller to downstream display-processing logic while operating from 3.3 V. Its 48-pin TSSOP package supports dense board layouts, but routing quality remains critical because uneven differential impedance, excessive trace length, or improper termination can reduce timing margin. Layout should use uninterrupted ground planes, closely coupled LVDS pairs, short return paths, and the decoupling arrangement specified by the manufacturer datasheet.
Recommandé
Video Timing Interface
The DS90CF364AMTDX can terminate the receiver side of a video timing link when the system uses an 18-bit differential data bus at up to 65 MHz. This makes it appropriate for timing-controller and display-interface assemblies that require a fixed 3.3 V supply and a 48-pin TSSOP footprint. The design benefit is the combination of an 18-bit parallel data interface and LVDS transport in one receiver IC. Timing closure must be based on the manufacturer's propagation-delay and setup/hold information rather than clock frequency alone, particularly when the cable and connector add propagation delay.
Recommandé
Human-Machine Interface Display
The DS90CF364AMTDX is a practical receiver for human-machine-interface panels using an 18-bit LVDS FPD link at 65 MHz. It allows a graphics or timing source to communicate with a panel assembly over differential conductors, which can improve robustness in industrial cabinets containing variable-speed motors and switching power conversion. The -10 °C to 70 °C operating range suits many indoor industrial environments, but enclosure temperature and display timing must be checked at worst case. PCB routing should retain the differential geometry specified for the 48-pin TSSOP implementation.
Recommandé
Embedded Display Controller
The DS90CF364AMTDX can serve as the panel-side receiver in an embedded display controller architecture where the graphics engine outputs an 18-bit LVDS stream. Its 65 MHz maximum signaling frequency supports the stated FPD-link class, while the 3.3 V supply allows integration with digital display-processing logic operating on the same rail. Designers must confirm that the controller's output lane count, data polarity, clock phase, and connector wiring match the receiver's documented terminal functions. Keep the LVDS section physically separated from high-current switching paths where practical.
Recommandé
Digital Signage Interface
The DS90CF364AMTDX is appropriate for digital-signage electronics that distribute an 18-bit display signal through an LVDS FPD link at up to 65 MHz. The receiver provides a defined integration point between a controller board and a display assembly while operating from 3.3 V. Since long cable connections and nearby power converters can introduce noise and impedance discontinuities, the implementation should use controlled-impedance board routing, appropriate connector transitions, and the receiver termination recommended by the manufacturer. Validate the complete channel across temperature because both the transmitter and display timing budget contribute to margin.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DS90CF364AMTDX — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DS90CF364MTDX/NOPB | DS90CF364AMTDX/NOPB |
|---|---|---|---|
| Package | 48-TSSOP (DGG) | 48-TSSOP | 48-TSSOP (DGG) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Function | 3.3 V LVDS FPD Receiver | LVDS FPD Receiver | 3.3 V LVDS FPD Receiver |
| Interface Width | 18 bits | 18 bits | 18 bits |
| Maximum Signaling Frequency | 65 MHz | 65 MHz | 65 MHz |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V |
| Pin Count | 48 pins | 48 pins | 48 pins |
| Mounting Type | Surface Mount | Surface Mount | Surface Mount |
Principaux différenciateurs
- Purpose-built 18-bit FPD receiver (vs DS90CF562MTD)
- Direct documented replacement path (vs DS90CF364MTDX/NOPB)
- Orderable 48-pin TSSOP configuration (vs DS90CF364AMTDX/NOPB)
Notes de conception
Route each LVDS differential pair on a continuous reference plane with tightly coupled spacing, matched intra-pair geometry, and minimal vias. Avoid routing the display link beneath switching-power nodes or parallel to high-current conductors. The 48-pin TSSOP receiver requires the manufacturer pin assignments to be copied exactly into the schematic and PCB footprint before fabrication.
Apply the input termination and decoupling arrangement specified by the Texas Instruments datasheet rather than copying a generic LVDS receiver layout. Check the complete channel for differential impedance, connector transitions, pair-length balance, and clock/data timing at the 65 MHz operating limit. These checks matter because the receiver can be electrically correct while the assembled channel still consumes the available timing margin.
Do not substitute a receiver solely because it uses a 48-pin TSSOP package or belongs to the DS90CF family. Confirm that every terminal has the same function, that the interface width and clock rate are acceptable, and that supply and I/O levels match. A complete replacement must also preserve the footprint, board keepouts, thermal layout, and trace topology.
Place the receiver's supply bypass capacitors close to the appropriate power terminals and connect them to a low-impedance ground plane. Keep the LVDS return path continuous through every plane transition. Confirm the 3.3 V rail remains within the device limits at the receiver, particularly near a display timing controller or switching regulator operating under transient load.
Informations de conformité
The manufacturer product and ordering information identifies the device and package, but the available records do not explicitly state the requested compliance classifications. No compliance status has been inferred.