Texas Instruments

DS90CR216MTD - 21-Bit 66 MHz LVDS Receiver | TI

Référence : DS90CR216MTD ✓ Actif
3.3 V Vdss 48-pin TSSOP Package Rising edge Speed
MOQ : 1 |

DS90CR216MTD Présentation

The Texas Instruments DS90CR216MTD is a 3.3 V rising-edge data-strobe LVDS receiver for a 21-bit Channel Link interface operating up to 66 MHz, housed in a 48-pin TSSOP package. It accepts three differential data pairs plus a differential clock pair, returning 21 parallel data bits and one clock in a serialized-to-parallel interface commonly used for high-speed backplane and inter-board communication.

A Channel Link receiver is a low-voltage differential signaling receiver that recovers parallel logic data from a serialized LVDS link. Its position in the signal chain is transmitter, twisted-pair cable, receiver, and parallel logic destination. By multiplexing up to 21 data lines plus one clock onto as few as nine conductors, the interface reduces cable width while preserving the noise immunity associated with differential signaling.

The device's principal features include a 21-bit parallel output, a 66 MHz maximum signaling rate, 3.3 V operation, LVDS-compatible differential inputs, and rising-edge data strobe. The 48-pin TSSOP package provides a practical surface-mount footprint for systems where cable reduction and low-voltage differential signaling are more important than minimizing connector count.

The DS90CR216 is designed for point-to-point links carrying serialized data between boards, backplanes, or rack-mounted equipment. Its 3:1 multiplexing architecture reduces the number of transmission lines relative to a conventional parallel bus while retaining a differential clock lane. The receiver's separate data and clock outputs allow the receiving logic to capture the recovered data using the supplied clock signal.

Typical applications include industrial control systems, test equipment, instrumentation racks, high-speed backplanes, video-processing modules, and embedded communication links. Because the interface is voltage-based rather than a current-mode driver topology, board designers should treat the LVDS input routing as a controlled-impedance transmission-line problem and maintain a continuous return path beneath the pair.

The primary design consideration is signal integrity. Route each differential pair as a tightly coupled pair over a controlled-impedance board, keep stub lengths short, and place receiver termination close to the device pins. Confirm the cable length, connector loss, and receiver tolerance against the channel-link operating limits before releasing a multi-board system.

This page combines manufacturer family information, package and interface details, sourcing links, replacement analysis, and practical LVDS layout guidance to help engineers evaluate the DS90CR216MTD for 21-bit channel-link systems.

Alternatives de remplacement direct pour DS90CR216MTD — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

DS90CR216AMTD

✅ Remplacement direct
📦 48-pin TSSOP
No functional or terminal difference documented; the source identifies identical package and terminals and states that no modification is required, giving 100% compatibility.

📋 Alternative de référence (hors catalogue)

DS90CR216MTD Spécifications

Product Type LVDS Channel Link receiver
Tension d'alimentation 3.3 V
Maximum Data Rate 66 MHz
Channel Width 21 bits
Data Interface 21-bit parallel
Clock Edge Rising edge
Input Signaling LVDS
Strobe Type Data strobe
Boîtier 48-pin TSSOP
Type de montage Surface mount
Statut RoHS unknown
REACH Status unknown

Guide de configuration des broches du DS90CR216MTD 48-pin tssop

Configuration des broches du DS90CR216MTD (boîtier 48-pin tssop). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier 48-pin tssop pour le DS90CR216MTD

Aucune donnée de brochage détaillée disponible pour DS90CR216MTD.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

DS90CR216MTD convient pour 6 applications: Industrial Backplane Communication, Test and Measurement Instrumentation, High-Speed Data Acquisition Modules, Video Processing Equipment, Embedded Communication Link, Rack-Mounted Control Systems.

🏭

Industrial Backplane Communication

The DS90CR216MTD fits a backplane link that must move a 21-bit parallel payload across a narrow cable while maintaining LVDS noise immunity. Its 66 MHz Channel Link rate and 21-bit parallel output suit control, instrumentation, and data-acquisition chassis that exchange synchronized data between plug-in boards. The reduced conductor count simplifies cable construction and connector density, while differential routing improves margin against internally generated noise. Board designers should preserve pair coupling, match input pair lengths, and maintain a continuous return plane through the receiver region.

🔧

Test and Measurement Instrumentation

The DS90CR216MTD is suitable for bench and rack instrumentation that transfers a parallel acquisition or control word across a board-to-board cable. Its 21-bit parallel output can feed FPGA or processor logic, while the separate recovered clock supports deterministic sampling. The 66 MHz interface rate accommodates moderate-speed instrument interconnects without requiring a wide multi-conductor ribbon cable. Use a low-skew cable, controlled-impedance routing, and receiver placement close to the connector to keep channel timing consistent across repeated test cycles.

📡

High-Speed Data Acquisition Modules

The DS90CR216MTD can terminate a differential Channel Link connection between a data-acquisition module and a processing backplane. Its 21-bit output width accommodates multi-channel results, status flags, and timing information, while the 66 MHz link rate provides a practical transfer rate for continuously refreshed measurement data. The reduced cable width is valuable in modular instruments where card spacing and connector density are constrained. Confirm the payload mapping and clock domain before connecting acquisition logic to the recovered outputs.

📺

Video Processing Equipment

The DS90CR216MTD can provide a compact board-to-board transport for control and pixel-related data in multi-board video equipment. Twenty-one parallel bits and a recovered clock are well suited to transferring timed data between processing and interface cards, while LVDS signaling supports reliable transmission over short controlled-impedance interconnects. The approach is most appropriate for companion cards that share a defined Channel Link protocol. Validate pixel timing, latency tolerance, and connector loss against the system video requirements.

🧩

Embedded Communication Link

The DS90CR216MTD is useful when an embedded subsystem must exchange a 21-bit control or status word with a remote card through a low-voltage differential link. Its 3.3 V supply operation aligns with many modern digital subsystems, and the multiplexed interface reduces the number of conductors needed compared with driving every parallel signal separately. The 66 MHz ceiling gives designers room for synchronized transfers without an unnecessarily fast serial protocol. Use the recovered clock only after verifying its phase and timing relative to the transmitted data.

🖥️

Rack-Mounted Control Systems

The DS90CR216MTD supports rack-mounted control and monitoring systems where subassemblies exchange parallel data over compact shielded cables. The 21-bit output and 66 MHz operation are suitable for command, measurement, and diagnostic traffic between cards, while the narrow differential connection simplifies chassis wiring. Because LVDS margin depends on the complete transmitter-to-receiver channel, specify the cable type, characteristic impedance, and connector geometry with the transmitter. Place the receiver close to the input connector and keep the pair away from switching-power nodes.

Récapitulatif des produits recommandés

DS90CR215 Channel Link transmitter for the remote link Utilisé dans : Industrial Backplane Communication, Test and Measurement Instrumentation, High-Speed Data Acquisition Modules, Video Processing Equipment, Embedded Communication Link, Rack-Mounted Control Systems DS90CR216 Device family containing the DS90CR216 receiver Utilisé dans : Industrial Backplane Communication, Test and Measurement Instrumentation, High-Speed Data Acquisition Modules, Video Processing Equipment, Embedded Communication Link, Rack-Mounted Control Systems
What is the DS90CR216MTD used for?
The DS90CR216MTD is a 3.3 V LVDS receiver for a 21-bit Channel Link interface operating up to 66 MHz. According to the Texas Instruments DS90CR216 product page, it receives serialized differential data and provides parallel data and clock outputs. It is suited to point-to-point links between circuit boards, backplanes, and rack-mounted equipment where reducing the number of cable conductors is important.
What are the key specifications of DS90CR216MTD that engineers should know?
The DS90CR216MTD combines a 21-bit parallel output, a maximum 66 MHz signaling rate, 3.3 V operation, and rising-edge data strobing in a 48-pin TSSOP package. Texas Instruments describes the device as an LVDS 21-bit Channel Link receiver. The defining implementation detail is differential serial signaling with multiplexed data lanes, reducing the conductor count required relative to a wide parallel bus.
Is DS90CR216MTD a transmitter or a receiver?
The DS90CR216MTD is the receiver in the DS90CR215 and DS90CR216 Channel Link chipset. The TI product page identifies the DS90CR216 as an LVDS 21-bit Channel Link receiver, while the associated manufacturer datasheet covers both the DS90CR215 and DS90CR216 devices. The receiver accepts the differential serialized link and converts it into parallel data and clock outputs.
Where can I download the DS90CR216MTD datasheet PDF?
The official DS90CR216 datasheet is available from the Texas Instruments literature link at https://www.ti.com/lit/gpn/ds90cr216, and the product page is located at https://www.ti.com/product/DS90CR216. These documents contain the DS90CR215 and DS90CR216 family information, electrical characteristics, pin configuration, and application guidance needed to evaluate the receiver.
Where can I find the DS90CR216MTD pinout and package details?
The DS90CR216MTD uses a 48-pin TSSOP package, as stated on the Texas Instruments product page and distributor listings. Use the pin-configuration table in the manufacturer DS90CR216 datasheet when assigning PCB nets. The verified package listing does not include the individual terminal names, so the page does not reproduce a pin-by-pin assignment that could be misapplied during layout.
What is the difference between DS90CR216MTD and DS90CR216AMTD?
The DS90CR216AMTD is a complete replacement for the DS90CR216MTD according to the FindIC comparison, which states that the terminals and packages are consistent and that replacement requires no modification. Both devices are identified as 48-pin TSSOP Channel Link receivers. The comparison records package and terminal equivalence rather than a functional difference.
What is the best drop-in replacement for DS90CR216MTD?
The DS90CR216AMTD is the best documented drop-in replacement for the DS90CR216MTD because the FindIC comparison identifies it as a complete replacement with consistent terminals, package, and functional characteristics. It uses the same 48-pin TSSOP package and requires no board modification. No cross-manufacturer part with equivalent documentation and verified pin compatibility was identified.
Can DS90CR216AMTD replace DS90CR216MTD without a PCB change?
Yes, the DS90CR216AMTD can replace the DS90CR216MTD without a PCB change based on the FindIC component comparison, which identifies consistent terminals and packages and describes the part as a complete replacement. Both are 48-pin TSSOP devices in the 21-bit, 66 MHz Channel Link receiver family. Confirm the exact ordering code and supply conditions before committing to a production build.
When should I choose DS90CR216MTD over another 21-bit LVDS receiver?
Choose the DS90CR216MTD when the system specifically uses the TI Channel Link ecosystem, a 21-bit parallel data path, a 66 MHz link rate, and a 48-pin TSSOP footprint. The device is appropriate when a documented DS90CR216AMTD alternate is unavailable. For a different serializer or a different multiplexing ratio, verify all timing, protocol, and pin requirements rather than assuming interface-level interchangeability.
Is DS90CR216MTD suitable for a 66 MHz backplane link?
The DS90CR216MTD is rated for a Channel Link signaling rate up to 66 MHz, making it a candidate for a 66 MHz backplane connection. Suitability also depends on trace impedance, pair coupling, connector loss, clock skew, and channel length. Use the transmitter and receiver timing information in the manufacturer datasheet to verify the complete channel rather than relying on the device frequency alone.
How should LVDS pairs be routed for DS90CR216MTD?
Route each DS90CR216MTD differential input as a tightly coupled pair with a continuous reference plane and impedance controlled to the board stack-up. Keep the pair length matched, minimize vias and stubs, and place any required termination close to the receiver. The 3.3 V LVDS interface is susceptible to reflections if the interconnect is treated as an uncontrolled set of point-to-point traces.
Does DS90CR216MTD need an external termination network?
The DS90CR216MTD is used with a compliant LVDS Channel Link interface, and the receiver termination arrangement must follow the connection and device requirements in the manufacturer datasheet. The verified product information does not state a universal termination value. Confirm the termination topology for the selected transmitter, cable, and receiver configuration before PCB release.
Where can I buy DS90CR216MTD online?
The DS90CR216MTD can be requested through the Request a Quote form on this page for current commercial availability, lead time, and a lot-consistent quotation. The Texas Instruments product page provides manufacturer ordering information, while distributor listings identify the exact 48-pin TSSOP ordering code. Because availability changes by region and quantity, request a current quote rather than relying on cached stock status.
What is the price of DS90CR216MTD?
Current pricing for the DS90CR216MTD should be obtained through the Request a Quote form on this page so the commercial terms match the required quantity, date code, and shipment destination. The verified listings include a distributor price reference, but no complete quantity-break schedule with printed tier quantities was captured. Use the quote form for a binding commercial response.
What is the lead time for DS90CR216MTD?
The current lead time for DS90CR216MTD should be confirmed through the Request a Quote form on this page, including the requested quantity and manufacturing schedule. Distributor listings indicate that the part is marketed for shipment, but a guaranteed factory or distribution lead time is not stated in the product information. A quote response should state the current available quantity and expected delivery timing.
Is DS90CR216MTD in stock?
Stock status for DS90CR216MTD changes with inventory level and order quantity, so the Request a Quote form on this page is the appropriate source for a current availability confirmation. The Texas Instruments product page and distributor listings show the part as a maintained ordering option. Request a lot-consistent quotation with the required quantity and target delivery date.
Is there a cross-brand equivalent for DS90CR216MTD?
No cross-brand drop-in equivalent is confirmed for the DS90CR216MTD because the Channel Link interface includes device-specific protocol, timing, and pin behavior that cannot be established from a generic parametric match. The documented replacement is the same-manufacturer DS90CR216AMTD. When evaluating another supplier's receiver, verify the complete terminal mapping, multiplexing architecture, clocking scheme, and link timing.

Données de référence d'ingénierie pour DS90CR216MTD — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Select the DS90CR216MTD when the design already uses the TI DS90CR215/DS90CR216 Channel Link interface and requires a 21-bit parallel receiver in a 48-pin TSSOP footprint. The documented DS90CR216AMTD alternative is preferable when the original ordering code is unavailable, because it uses the same package and terminals and does not require PCB modification. Do not choose a generic 21-bit LVDS receiver based on output width alone; the multiplexing scheme, recovered-clock behavior, timing, and terminal mapping must also match. For systems needing more data lanes, a different multiplexing ratio, a different serializer protocol, or a smaller package, redesign is required. Confirm the 66 MHz channel margin over the intended cable and connector, then validate the layout with the manufacturer's interface guidance.

Comparaison avec les alternatives

Paramètre Ce produit DS90CR216AMTD
Brand Texas Instruments Texas Instruments
Package 48-pin TSSOP 48-pin TSSOP
Device Type LVDS 21-bit Channel Link receiver LVDS 21-bit Channel Link receiver
Supply Voltage 3.3 V 3.3 V
Maximum Data Rate 66 MHz 66 MHz
Channel Width 21 bits 21 bits
Clock Edge Rising edge Rising edge
Input Signaling LVDS LVDS
Mounting Type Surface mount Surface mount
Pin Compatibility 48-pin TSSOP reference configuration Identical package and terminals; complete replacement without modification

Principaux différenciateurs

  • Documented no-modification replacement path (vs DS90CR216AMTD)
  • Same 21-bit Channel Link electrical function (vs DS90CR216AMTD)
  • No unsupported cross-brand substitution recommended (vs Generic LVDS interface IC alternatives)

Notes de conception

Route every receiver input as a controlled-impedance differential pair, with the pair members closely coupled and referenced to a continuous ground plane. Match the pair length within the tolerance stated in the manufacturer interface guidance, minimize vias, and avoid stubs. The 21 data bits and clock are recovered from differential inputs, so a discontinuity at a connector or package transition can directly reduce eye margin and create data errors.

Treat the complete path from the DS90CR215 transmitter through the cable and connector to the DS90CR216MTD receiver as one channel. Characteristic impedance, attenuation, skew, and connector return loss determine whether the 66 MHz link has usable timing margin. Use the manufacturer Channel Link timing information to validate the source-synchronous clock and data relationship rather than treating the receiver frequency rating as a guaranteed end-to-end performance figure.

Do not substitute a generic 21-bit LVDS receiver solely because the pin count or parallel-output width matches. Channel Link compatibility includes the multiplexing scheme, clock recovery behavior, data-strobe timing, and protocol mapping. When replacing the DS90CR216MTD, verify the complete terminal arrangement and operating conditions. The documented DS90CR216AMTD option has consistent package and terminals and requires no board modification.

Keep the LVDS pair away from high-current switching nodes and provide a continuous return path so common-mode current does not flow into the receiver reference network. Ground and power planes should be treated as part of the transmission-line structure. Avoid placing test points as unmatched stubs on the differential inputs, and follow the connector and cable recommendations in the manufacturer application information.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The manufacturer product information confirms the device family and package but does not explicitly state RoHS, REACH, halogen-free, or conflict-minerals status. The listed NOPB ordering suffix is not used to infer lead-free compliance for the target ordering code.

Données vérifiées le : 2026-11-10 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

DS90CR216MTD datasheet DS90CR216MTD pinout DS90CR216MTD datasheet pdf DS90CR216MTD equivalent DS90CR216MTD replacement DS90CR216MTD cross reference DS90CR216MTD vs DS90CR216AMTD DS90CR216MTD 48-TSSOP receiver DS90CR216MTD 21-bit 66 MHz DS90CR216MTD LVDS backplane DS90CR216MTD price DS90CR216MTD stock Texas Instruments DS90CR216MTD DS90CR216 Channel Link receiver

Composants & termes associés

Texas Instruments DS90CR216MTD DS90CR216 DS90CR216AMTD DS90CR215 Channel Link LVDS receiver 21-bit parallel interface data strobe rising-edge clocking 66 MHz signaling rate 3.3 V power supply 48-pin TSSOP surface mount low-voltage differential signaling differential clock input multiplexed data lanes point-to-point serial link controlled-impedance routing industrial backplane test and measurement instrumentation data acquisition rack-mounted control system channel-link serialization
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ