DS90CR216MTD - 21-Bit 66 MHz LVDS Receiver | TI
부품 번호: DS90CR216MTD ✓ 활성DS90CR216MTD 개요
A Channel Link receiver is a low-voltage differential signaling receiver that recovers parallel logic data from a serialized LVDS link. Its position in the signal chain is transmitter, twisted-pair cable, receiver, and parallel logic destination. By multiplexing up to 21 data lines plus one clock onto as few as nine conductors, the interface reduces cable width while preserving the noise immunity associated with differential signaling.
The device's principal features include a 21-bit parallel output, a 66 MHz maximum signaling rate, 3.3 V operation, LVDS-compatible differential inputs, and rising-edge data strobe. The 48-pin TSSOP package provides a practical surface-mount footprint for systems where cable reduction and low-voltage differential signaling are more important than minimizing connector count.
The DS90CR216 is designed for point-to-point links carrying serialized data between boards, backplanes, or rack-mounted equipment. Its 3:1 multiplexing architecture reduces the number of transmission lines relative to a conventional parallel bus while retaining a differential clock lane. The receiver's separate data and clock outputs allow the receiving logic to capture the recovered data using the supplied clock signal.
Typical applications include industrial control systems, test equipment, instrumentation racks, high-speed backplanes, video-processing modules, and embedded communication links. Because the interface is voltage-based rather than a current-mode driver topology, board designers should treat the LVDS input routing as a controlled-impedance transmission-line problem and maintain a continuous return path beneath the pair.
The primary design consideration is signal integrity. Route each differential pair as a tightly coupled pair over a controlled-impedance board, keep stub lengths short, and place receiver termination close to the device pins. Confirm the cable length, connector loss, and receiver tolerance against the channel-link operating limits before releasing a multi-board system.
This page combines manufacturer family information, package and interface details, sourcing links, replacement analysis, and practical LVDS layout guidance to help engineers evaluate the DS90CR216MTD for 21-bit channel-link systems.
드롭인 대체품: DS90CR216MTD — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
DS90CR216AMTD
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DS90CR216MTD 사양
| Product Type | LVDS Channel Link receiver |
| 공급 전압 | 3.3 V |
| Maximum Data Rate | 66 MHz |
| Channel Width | 21 bits |
| Data Interface | 21-bit parallel |
| Clock Edge | Rising edge |
| Input Signaling | LVDS |
| Strobe Type | Data strobe |
| 패키지 | 48-pin TSSOP |
| 실장 유형 | Surface mount |
| RoHS 상태 | unknown |
| REACH Status | unknown |
DS90CR216MTD 48-pin tssop 핀 구성 가이드
DS90CR216MTD(48-pin tssop 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: DS90CR216MTD.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
DS90CR216MTD 적합 용도: 6 애플리케이션s: Industrial Backplane Communication, Test and Measurement Instrumentation, High-Speed Data Acquisition Modules, Video Processing Equipment, Embedded Communication Link, Rack-Mounted Control Systems.
Industrial Backplane Communication
The DS90CR216MTD fits a backplane link that must move a 21-bit parallel payload across a narrow cable while maintaining LVDS noise immunity. Its 66 MHz Channel Link rate and 21-bit parallel output suit control, instrumentation, and data-acquisition chassis that exchange synchronized data between plug-in boards. The reduced conductor count simplifies cable construction and connector density, while differential routing improves margin against internally generated noise. Board designers should preserve pair coupling, match input pair lengths, and maintain a continuous return plane through the receiver region.
추천
Test and Measurement Instrumentation
The DS90CR216MTD is suitable for bench and rack instrumentation that transfers a parallel acquisition or control word across a board-to-board cable. Its 21-bit parallel output can feed FPGA or processor logic, while the separate recovered clock supports deterministic sampling. The 66 MHz interface rate accommodates moderate-speed instrument interconnects without requiring a wide multi-conductor ribbon cable. Use a low-skew cable, controlled-impedance routing, and receiver placement close to the connector to keep channel timing consistent across repeated test cycles.
추천
High-Speed Data Acquisition Modules
The DS90CR216MTD can terminate a differential Channel Link connection between a data-acquisition module and a processing backplane. Its 21-bit output width accommodates multi-channel results, status flags, and timing information, while the 66 MHz link rate provides a practical transfer rate for continuously refreshed measurement data. The reduced cable width is valuable in modular instruments where card spacing and connector density are constrained. Confirm the payload mapping and clock domain before connecting acquisition logic to the recovered outputs.
추천
Video Processing Equipment
The DS90CR216MTD can provide a compact board-to-board transport for control and pixel-related data in multi-board video equipment. Twenty-one parallel bits and a recovered clock are well suited to transferring timed data between processing and interface cards, while LVDS signaling supports reliable transmission over short controlled-impedance interconnects. The approach is most appropriate for companion cards that share a defined Channel Link protocol. Validate pixel timing, latency tolerance, and connector loss against the system video requirements.
추천
Embedded Communication Link
The DS90CR216MTD is useful when an embedded subsystem must exchange a 21-bit control or status word with a remote card through a low-voltage differential link. Its 3.3 V supply operation aligns with many modern digital subsystems, and the multiplexed interface reduces the number of conductors needed compared with driving every parallel signal separately. The 66 MHz ceiling gives designers room for synchronized transfers without an unnecessarily fast serial protocol. Use the recovered clock only after verifying its phase and timing relative to the transmitted data.
추천
Rack-Mounted Control Systems
The DS90CR216MTD supports rack-mounted control and monitoring systems where subassemblies exchange parallel data over compact shielded cables. The 21-bit output and 66 MHz operation are suitable for command, measurement, and diagnostic traffic between cards, while the narrow differential connection simplifies chassis wiring. Because LVDS margin depends on the complete transmitter-to-receiver channel, specify the cable type, characteristic impedance, and connector geometry with the transmitter. Place the receiver close to the input connector and keep the pair away from switching-power nodes.
추천
추천 제품 요약
엔지니어링 참조 데이터: DS90CR216MTD — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | DS90CR216AMTD |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 48-pin TSSOP | 48-pin TSSOP |
| Device Type | LVDS 21-bit Channel Link receiver | LVDS 21-bit Channel Link receiver |
| Supply Voltage | 3.3 V | 3.3 V |
| Maximum Data Rate | 66 MHz | 66 MHz |
| Channel Width | 21 bits | 21 bits |
| Clock Edge | Rising edge | Rising edge |
| Input Signaling | LVDS | LVDS |
| Mounting Type | Surface mount | Surface mount |
| Pin Compatibility | 48-pin TSSOP reference configuration | Identical package and terminals; complete replacement without modification |
주요 차별점
- Documented no-modification replacement path (vs DS90CR216AMTD)
- Same 21-bit Channel Link electrical function (vs DS90CR216AMTD)
- No unsupported cross-brand substitution recommended (vs Generic LVDS interface IC alternatives)
설계 노트
Route every receiver input as a controlled-impedance differential pair, with the pair members closely coupled and referenced to a continuous ground plane. Match the pair length within the tolerance stated in the manufacturer interface guidance, minimize vias, and avoid stubs. The 21 data bits and clock are recovered from differential inputs, so a discontinuity at a connector or package transition can directly reduce eye margin and create data errors.
Treat the complete path from the DS90CR215 transmitter through the cable and connector to the DS90CR216MTD receiver as one channel. Characteristic impedance, attenuation, skew, and connector return loss determine whether the 66 MHz link has usable timing margin. Use the manufacturer Channel Link timing information to validate the source-synchronous clock and data relationship rather than treating the receiver frequency rating as a guaranteed end-to-end performance figure.
Do not substitute a generic 21-bit LVDS receiver solely because the pin count or parallel-output width matches. Channel Link compatibility includes the multiplexing scheme, clock recovery behavior, data-strobe timing, and protocol mapping. When replacing the DS90CR216MTD, verify the complete terminal arrangement and operating conditions. The documented DS90CR216AMTD option has consistent package and terminals and requires no board modification.
Keep the LVDS pair away from high-current switching nodes and provide a continuous return path so common-mode current does not flow into the receiver reference network. Ground and power planes should be treated as part of the transmission-line structure. Avoid placing test points as unmatched stubs on the differential inputs, and follow the connector and cable recommendations in the manufacturer application information.
규정 준수 정보
The manufacturer product information confirms the device family and package but does not explicitly state RoHS, REACH, halogen-free, or conflict-minerals status. The listed NOPB ordering suffix is not used to infer lead-free compliance for the target ordering code.