DSPIC30F4013-30I/ML - 16-bit DSC 30MIPs 48KB Flash | Microchip
Référence : DSPIC30F4013-30I/ML ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $8.4 | $8,40 |
| 10 | $7.55 | $75,50 |
| 100 | $6.71 | $671,00 |
| 500 | $6.05 | $3 025,00 |
| 1 000 | $5.4 | $5 400,00 |
DSPIC30F4013-30I/ML Présentation
What is a Digital Signal Controller? A DSC sits between a microcontroller (MCU) and a full digital signal processor (DSP): it executes DSP-grade MAC operations and bit-reversed addressing for fast Fourier transforms, while still running a deterministic real-time control loop on the same chip. The dsPIC30F is the original DSC family from Microchip and targets motor control, switched-mode power supply (SMPS) control, and sensor conditioning, where one core handles both analog sampling and high-speed control math. In the broader taxonomy, a DSC is a microcontroller with a DSP engine -> microcontroller -> embedded processor -> semiconductor device.
Key features include a 6-channel, 10-bit ADC with 500 ksps conversion rate, dedicated motor-control PWM modules with up to 8 PWM outputs and complementary mode, a quadrature encoder interface (QEI), an input capture module, and three 16-bit timer/counters. Communication peripherals comprise UART, SPI, and I2C, plus a CAN 2.0B module for industrial networking. The CPU core uses a 16-bit native data path with a 24-bit instruction word, providing up to 30 MIPS throughput while maintaining deterministic interrupt response for control loops.
The device is fabricated in CMOS process technology and incorporates 2 KB of RAM plus 1 KB of EEPROM data memory, supporting in-application self-programming and nonvolatile parameter storage. Typical applications include brushless DC (BLDC) motor drives, permanent-magnet synchronous motor (PMSM) field-oriented control (FOC), uninterruptible power supplies (UPS), power factor correction (PFC) stages, and industrial sensor interfaces. The /ML package suits compact, high-density PCB layouts where thermal dissipation through the exposed pad is acceptable.
When designing with the DSPIC30F4013-30I/ML, place decoupling capacitors close to the VDD/VSS pairs and tie the exposed thermal pad of the QFN-44 to a ground plane for thermal and electrical performance. The dsPIC30F is supported by the MPLAB X IDE and the MPLAB XC16 C compiler with a free optimization level, and the MotorBench Development Tool and dsPICDEM motor-control starter kits shorten development time. This page synthesizes distributor pricing, drop-in alternatives in the QFN-44 footprint, and practical design notes not found in the manufacturer datasheet.
Alternatives de remplacement direct pour DSPIC30F4013-30I/ML — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec DSPIC30F4013-30I/ML (même facteur de forme et même empreinte) — différant par ADC, Core Architecture, Package, Motor Control PWM, Program Memory (Flash).
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
DSPIC30F4013-20I/ML
✅ Remplacement direct✓ En stock
$5.85 / unité
Voir la fiche technique →DSPIC30F4013T-30I/ML
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DSPIC30F4012-30I/ML
✅ Remplacement direct✓ En stock
$4.79 / unité
Voir la fiche technique →DSPIC30F4011-30I/ML
✅ Remplacement direct✓ En stock
$5.48 / unité
Voir la fiche technique →DSPIC30F4012-30I/P
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
DSPIC30F4013-30I/ML Valeurs maximales et caractéristiques électriques
| Core Architecture | dsPIC30F 16-bit Digital Signal Controller (modified Harvard) |
| Program Memory (Flash) | 48 KB (16K x 24 words) |
| Data RAM | 2 KB |
| Data EEPROM | 1024 bytes |
| Instruction Word Width | 24-bit |
| Maximum CPU Speed | 30 MIPS (MIPS grade "30") |
| Clock Speed (Internal) | 40 MHz |
| Supply Voltage (VDD) | 3.0 V to 5.5 V |
| Plage de température de fonctionnement | -40 °C to +85 °C (Industrial, "I") |
| Boîtier | QFN-44 (ML), 8 x 8 mm, 0.65 mm pitch, lead-free |
| I/O Pins | 20 |
| ADC | 6-channel, 10-bit, up to 500 ksps |
| Motor Control PWM | Up to 8 outputs, complementary mode with dead time |
| Quadrature Encoder Interface (QEI) | Yes |
| Communication Peripherals | UART, SPI, I2C, CAN 2.0B |
| Timers | 3 x 16-bit Timer/Counter |
| DMA Channels | 0 (no DMA on this device) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant (lead-free "/ML" suffix) |
Configuration des broches de DSPIC30F4013-30I/ML
| Broche 1 | EMUD/AN0/VREF+/CN2/RB0 — Emulation data / analog input 0 / VREF+ / change notification |
| Broche 2 | EMUC/AN1/VREF-/CN3/RB1 — Emulation clock / analog input 1 / VREF- / change notification |
| Broche 3 | AN2/SS1/CN4/RB2 — Analog input 2 / SPI1 slave select |
| Broche 4 | AN3/INDX/CN5/RB3 — Analog input 3 / QEI index |
| Broche 5 | AN4/QEA/IC7/CN6/RB4 — Analog input 4 / QEI phase A / input capture 7 |
| Broche 6 | AN5/QEB/OC8/CN7/RB5 — Analog input 5 / QEI phase B / output compare 8 |
| Broche 7 | VSS — Ground reference |
| Broche 8 | OSC1/CLKIN — Crystal oscillator input / external clock in |
| Broche 9 | OSC2/CLKOUT — Crystal oscillator output / system clock out |
| Broche 10 | TDI/AN6/CN8/RB6 — JTAG TDI / analog input 6 |
| Broche 11 | TMS/AN7/CN9/RB7 — JTAG TMS / analog input 7 |
| Broche 12 | TCK/AN8/CN10/RB8 — JTAG TCK / analog input 8 |
| Broche 13 | TDO/AN9/CN11/RB9 — JTAG TDO / analog input 9 |
| Broche 14 | VDD — Positive supply (3.0 V to 5.5 V) |
| Broche 15 | PWM1H/RE0 — PWM1 high-side output |
| Broche 16 | PWM1L/RE1 — PWM1 low-side output |
| Broche 17 | PWM2H/RE2 — PWM2 high-side output |
| Broche 18 | PWM2L/RE3 — PWM2 low-side output |
| Broche 19 | PWM3H/RE4 — PWM3 high-side output |
| Broche 20 | PWM3L/RE5 — PWM3 low-side output |
| Broche 21 | C1RX/RF0 — CAN1 receive |
| Broche 22 | C1TX/RF1 — CAN1 transmit |
| Broche 23 | U1RX/SDA1/IC1/RF2 — UART1 RX / I2C1 data / input capture 1 |
| Broche 24 | U1TX/SCL1/IC2/RF3 — UART1 TX / I2C1 clock / input capture 2 |
| Broche 25 | SCK1/INT0/RF4 — SPI1 clock / external interrupt 0 |
| Broche 26 | SDO1/INT1/RF5 — SPI1 data out / external interrupt 1 |
| Broche 27 | SDI1/INT2/RF6 — SPI1 data in / external interrupt 2 |
| Broche 28 | SS1/INT3/RF7 — SPI1 slave select (note: AN2/SS1 also on pin 3, second SS function) / external interrupt 3 |
| Broche 29 | VSS — Ground reference |
| Broche 30 | VDD — Positive supply (3.0 V to 5.5 V) |
| Broche 31 | SDA2/RG0 — I2C2 data |
| Broche 32 | SCL2/RG1 — I2C2 clock |
| Broche 33 | SCLKI/RG2 — Secondary clock input (RTC) |
| Broche 34 | FLTA/RG3 — PWM fault A input |
| Broche 35 | FLTB/RG4 — PWM fault B input |
| Broche 36 | OC1/RD0 — Output compare 1 |
| Broche 37 | OC2/RD1 — Output compare 2 |
| Broche 38 | OC3/RD2 — Output compare 3 |
| Broche 39 | OC4/RD3 — Output compare 4 |
| Broche 40 | T1CK/IC1/RD4 — Timer1 external clock / input capture 1 alt |
| Broche 41 | T2CK/IC2/RD5 — Timer2 external clock / input capture 2 alt |
| Broche 42 | T3CK/IC3/RD6 — Timer3 external clock / input capture 3 |
| Broche 43 | IC4/RD7 — Input capture 4 |
| Broche 44 | EP — Exposed thermal pad - tie to ground |
Applications typiques
DSPIC30F4013-30I/ML convient pour 6 applications: Brushless DC (BLDC) Motor Drive, Permanent Magnet Synchronous Motor (PMSM) Field-Oriented Control, Switched-Mode Power Supply (SMPS) Digital Control, Uninterruptible Power Supply (UPS) Controller, Industrial Sensor Signal Conditioning, Automotive Auxiliary Motor Control.
Brushless DC (BLDC) Motor Drive
The DSPIC30F4013-30I/ML is purpose-built for BLDC motor control, where its dedicated motor-control PWM module produces up to 8 complementary outputs with programmable dead time, directly driving a 3-phase inverter without external logic. The 30 MIPS core runs the trapezoidal commutation or field-oriented control (FOC) loop within 5-10 microseconds at 20 kHz PWM, while the 500 ksps 10-bit ADC samples phase currents synchronized to the PWM reload. Engineers typically place current-sense amplifiers on the low-side shunts and connect the analog inputs AN0-AN5 to the ADC, while the QEI module reads Hall or optical encoders for sensored commutation. Compared with a general-purpose MCU, the dsPIC30F eliminates the need for an external DSP chip and shrinks the BOM for fans, pumps, e-bikes, and appliance drives.
Recommandé
Permanent Magnet Synchronous Motor (PMSM) Field-Oriented Control
The DSPIC30F4013-30I/ML executes full FOC with Park and Clarke transforms on a PMSM at switching frequencies up to 20 kHz, sustained by its 30 MIPS core and single-cycle 16 x 16-bit MAC. The PWM module generates the space-vector modulation pattern with center-aligned mode and dead-time insertion, while the ADC triggers from PWM reload events to deliver deterministic sampling at the PWM valley point, eliminating switching-noise contamination. Onboard CAN 2.0B and UART allow real-time torque/speed command updates from an external controller. This combination of deterministic DSP performance and integrated motor peripherals makes the DSC a workhorse for servo drives, robotics joint motors, and electric-bicycle controllers where precise rotor-flux tracking is mandatory.
Recommandé
Switched-Mode Power Supply (SMPS) Digital Control
The DSPIC30F4013-30I/ML can replace traditional analog control loops in SMPS topologies including PFC, half-bridge converters, and full-bridge DC-DC stages. Its high-speed 10-bit ADC samples the output voltage and current at 500 ksps, the 30 MIPS core computes the digital compensator (PID or Type-III), and the motor-control PWM module doubles as the gate-drive timing generator with programmable frequency and dead-time control. The CAN and UART interfaces enable remote telemetry of input/output voltages, currents, and temperature to a host controller, supporting Industry 4.0 smart power supplies. The wide 3.0 V to 5.5 V supply range lets the DSC operate directly from the auxiliary bias winding of the converter without an intermediate LDO.
Recommandé
Uninterruptible Power Supply (UPS) Controller
In a true online UPS the DSPIC30F4013-30I/ML coordinates inverter control, battery charging, and load transfer within a single chip. The DSC monitors mains voltage through the ADC, drives the inverter bridge through its complementary PWM outputs with 8 channels, and executes the seamless transfer algorithm within microseconds of detecting a mains fault. Its 1 KB of EEPROM stores calibration constants, battery-aging parameters, and fault-history logs that survive power cycling, while CAN or UART links the UPS to building-management systems for remote diagnostics. The industrial -40 °C to +85 °C temperature range allows deployment in harsh electrical rooms without additional thermal management.
Recommandé
Industrial Sensor Signal Conditioning
The DSPIC30F4013-30I/ML's 16-bit DSP core runs FIR or IIR digital filters on sensor signals at high sample rates, offloading filtering work from a host PLC or remote-I/O module. The 6-channel ADC multiplexes thermocouples, strain gauges, or load-cell outputs, and the DSC's 30 MIPS budget runs both the digital filter and the linearization/compensation math in real time. CAN 2.0B and UART transmit conditioned data to a SCADA network, while the SPI port connects to a local display or keypad. This combination is widely deployed in weigh scales, force-test rigs, and process-control instrumentation where deterministic latency and on-chip DSP filtering are essential.
Recommandé
Automotive Auxiliary Motor Control
Although not AEC-Q100 qualified, the DSPIC30F4013-30I/ML is used in non-safety automotive subsystems such as HVAC blower control, water-pump drives, and adjustable pedal systems where its motor-control peripherals simplify firmware. The QEI module interfaces directly to a rotary encoder for closed-loop position control, while the complementary PWM outputs switch 12 V or 24 V automotive buses at 20 kHz without audible noise. CAN 2.0B integration connects the drive to the vehicle's body-control network, and the -40 °C to +85 °C industrial grade covers cabin and under-hood-adjacent placements. Automotive designs that require AEC-Q100 should evaluate the equivalent dsPIC33F automotive variants in the same QFN-44 footprint.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DSPIC30F4013-30I/ML — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DSPIC30F4013-20I/ML | DSPIC30F4013T-30I/ML | DSPIC30F4012-30I/ML | DSPIC30F4011-30I/ML | DSPIC30F4012-30I/P |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | QFN-44 (ML), 8x8 mm | QFN-44 (ML) - same | QFN-44 (ML) - same | QFN-44 (ML) - same | QFN-44 (ML) - same | DIP-40 - different package |
| Max CPU Speed (MIPS) | 30 MIPS | 20 MIPS | 30 MIPS | 30 MIPS | 30 MIPS | 30 MIPS |
| Flash Program Memory | 48 KB | 48 KB | 48 KB | 24 KB | 12 KB | 24 KB |
| RAM | 2 KB | 2 KB | 2 KB | 2 KB | 1 KB | 2 KB |
| ADC Channels / Resolution | 6 / 10-bit | 6 / 10-bit | 6 / 10-bit | 6 / 10-bit | 6 / 10-bit | 6 / 10-bit |
| CAN 2.0B Module | Yes | Yes | Yes | Yes | Yes | Yes |
| Temperature Range | -40 °C to +85 °C (Industrial) | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
Principaux différenciateurs
- Single-cycle 16 x 16-bit MAC at 30 MIPS with motor-control peripherals integrated (vs DSPIC30F4011-30I/ML)
- Higher CPU throughput than the 20 MIPS grade at the same Flash capacity (vs DSPIC30F4013-20I/ML)
- QFN-44 (ML) industrial-grade packaging in compact 8x8 mm footprint (vs DSPIC30F4013-30I/PT (TQFP-44, 10x10 mm))
Notes de conception
The QFN-44 (ML) package dissipates heat primarily through the exposed thermal pad (pin 44). Solder this pad to a copper plane of at least 1 square inch on the top or bottom PCB layer, with multiple thermal vias to inner copper layers. Estimated: at 30 MIPS with all peripherals active the device draws roughly 35 mA at 5 V (175 mW), well within the package's thermal rating of approximately 30 °C/W theta_JB. For high-temperature enclosed designs, derate by 1 mW/°C above 25 °C ambient. The DIP-40 (/P) variant in DSPIC30F4012-30I/P has a higher theta_JA and is preferred for through-hole prototyping but not the QFN target.
Place a 0.1 µF ceramic decoupling capacitor within 5 mm of each VDD/VSS pair (pins 7, 14, 29, 30). Add a bulk 10 µF tantalum or ceramic capacitor near the main VDD pin (pin 14) to handle transient switching currents from the ADC and PWM peripherals. The OSC1/OSC2 crystal (pins 8/9) should be placed within 5 mm of the IC with a continuous ground ring on the top layer; avoid routing digital signal traces under the crystal to prevent crosstalk. Keep analog traces (AN0-AN5) short and isolated from PWM switching traces to avoid coupling.
Do not exceed the maximum VDD of 5.5 V: the dsPIC30F family is not 3.3 V tolerant on 5 V inputs by default - configure all digital I/O as inputs only when the pin voltage is within the active VDD range, otherwise use external level shifters. The configuration bits (FOSC, FWDT, FBORPOR, etc.) must be set correctly at programming time, or the device may fail to start; use MPLAB X IDE's configuration bit window. Avoid stacking firmware updates without verifying interrupt-vector offsets, since the dsPIC30F vector table is fixed at program-memory start.
The PWM outputs (PWM1H/L, PWM2H/L, PWM3H/L on pins 15-20) drive high-current gates and produce dv/dt up to 5 kV/µs. Place gate-drive resistors and bootstrap capacitors within 10 mm of these pins to minimize parasitic inductance. Keep the analog ground (AGND) and digital ground (DGND) planes joined at a single point near the VDD decoupling capacitor to avoid ground bounce coupling into the ADC readings. For CAN bus applications, place the MCP2551 or ATA6563 transceiver within 50 mm of pins 21-22 (C1RX/C1TX) and use a 120 Ω termination resistor at each bus end.
Informations de conformité
RoHS compliance indicated by "/ML" lead-free suffix per Microchip product page. Industrial temperature grade only; no AEC-Q100 automotive variant in the dsPIC30F4013 family. For automotive applications, use the dsPIC33F AEC-Q100 variants.
