DSPIC30F6013T-30I/PF - 16-bit DSC, 132KB Flash, 30MIPs | Microchip
Référence : DSPIC30F6013T-30I/PF ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $14.5 | $14,50 |
| 10 | $13.2 | $132,00 |
| 100 | $11.85 | $1 185,00 |
| 500 | $10.45 | $5 225,00 |
| 1 000 | $9.2 | $9 200,00 |
DSPIC30F6013T-30I/PF Présentation
What is a Digital Signal Controller? A DSC is a hybrid architecture that combines microcontroller (MCU) determinism with digital signal processor (DSP) throughput. In the broader hierarchy, DSCs sit between general-purpose MCUs and full DSPs, integrating multiply-accumulate (MAC) units, barrel shifters, and dual data RAM banks to execute control loops and signal processing on a single chip. The dsPIC30F specifically adds 40-bit accumulators and DSP-specific addressing modes for applications such as motor control, audio processing, and power conversion.
Key features of the DSPIC30F6013T-30I/PF include a 16-bit data path with modified Harvard architecture, 12-bit ADC with up to 16 channels, multiple communication peripherals (UART, SPI, I2C, CAN), PWM modules suitable for three-phase motor control, and a wide operating voltage range from 2.5V to 5.5V. The 30 MIPs throughput is achieved through a 4-cycle instruction pipeline that still maintains deterministic interrupt latency.
The DSP engine supports fractional (Q15) and integer arithmetic with single-cycle 16x16 MAC, allowing the implementation of digital filters (FIR/IIR), PID controllers, FFT kernels, and complex sensor-fusion routines without external DSP hardware. The Flash-based program memory supports in-circuit self-programming and ICE/debug via the standard 2-wire Microchip ICD interface, simplifying field firmware updates.
Typical applications include industrial motor drives (BLDC, PMSM, ACIM), automotive body controllers, digital power conversion (UPS, solar inverters), sensor signal conditioning, and low-cost audio effect processors. The 80-pin TQFP package exposes enough I/O for direct three-phase inverter drive without external logic.
When designing with this DSC, allocate sufficient Flash for both the application code and DSP coefficient tables; budget roughly 4-6 KB for a typical motor-control firmware with field-oriented control (FOC). Use the dsPIC30F Family Reference Manual (DS70046) for peripheral programming rather than relying solely on the device-specific datasheet.
This page synthesizes distributor stock signals, drop-in same-family variants, and application-level design guidance beyond the device datasheet, giving procurement and embedded engineers a faster path to BOM decisions and code bring-up.
Alternatives de remplacement direct pour DSPIC30F6013T-30I/PF — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec DSPIC30F6013T-30I/PF (même facteur de forme et même empreinte) — différant par Package, ADC, RoHS Status, Operating Temperature, Core Architecture.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
DSPIC30F6014T-30I/PF
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
DSPIC30F6013AT-30I/PT
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DSPIC30F6013A-30I/PF
✅ Remplacement direct✓ En stock
$14.2 / unité
Voir la fiche technique →DSPIC30F6013A-30I/PT
✅ Remplacement direct✓ En stock
$10.93 / unité
Voir la fiche technique →DSPIC30F6012AT-30I/PF
✅ Remplacement direct✓ En stock
$11.2 / unité
Voir la fiche technique →DSPIC30F6011AT-30I/PT
✅ Remplacement direct✓ En stock
$7.5 / unité
Voir la fiche technique →DSPIC30F6013T-30I/PF Valeurs maximales et caractéristiques électriques
| Core Architecture | dsPIC30F 16-bit DSC (modified Harvard) |
| Instruction Set | 16-bit RISC with DSP extensions |
| Maximum CPU Speed | 30 MIPS at 30 MHz |
| Program Memory | 132 KB (44K x 24) Flash |
| Data RAM | 6 KB (6144 bytes) |
| Operating Voltage | 2.5 V to 5.5 V |
| Boîtier | 80-pin TQFP (14x14 mm, 1.0 mm height) |
| Type de montage | Surface Mount |
| Température de fonctionnement | -40C to +85C (Industrial) |
| Statut RoHS | ROHS3 Compliant |
| Programming/Debug | ICD via 2-wire interface (PGEDx/PGECx) |
| Packaging | Tape & Reel (TR) |
| Series | dsPIC30F |
Configuration des broches de DSPIC30F6013T-30I/PF
| Broche 1 | AN0 — Analog input 0 / VREF+ |
| Broche 2 | AN1 — Analog input 1 |
| Broche 3 | AN2 — Analog input 2 |
| Broche 4 | AN3 — Analog input 3 |
| Broche 5 | AN4 — Analog input 4 |
| Broche 6 | AN5 — Analog input 5 |
| Broche 7 | AN6 — Analog input 6 |
| Broche 8 | AN7 — Analog input 7 |
| Broche 9 | VDD — Core logic supply (2.5V-5.5V) |
| Broche 10 | VSS — Ground |
| Broche 11 | OSC1 — Crystal oscillator input |
| Broche 12 | OSC2 — Crystal oscillator output |
| Broche 13 | MCLR — Master Clear (reset, active low) |
| Broche 14 | PGED1 — Programming/Debug data |
| Broche 15 | PGEC1 — Programming/Debug clock |
| Broche 16 | PGED2 — Secondary programming data |
| Broche 17 | PGEC2 — Secondary programming clock |
| Broche 18 | RA0 — I/O port A bit 0 |
| Broche 19 | RA1 — I/O port A bit 1 |
| Broche 20 | RA2 — I/O port A bit 2 |
| Broche 21 | RA3 — I/O port A bit 3 |
| Broche 22 | RA4 — I/O port A bit 4 |
| Broche 23 | RA5 — I/O port A bit 5 |
| Broche 24 | RA6 — I/O port A bit 6 |
| Broche 25 | RA7 — I/O port A bit 7 |
| Broche 26 | RB0 — I/O port B bit 0 |
| Broche 27 | RB1 — I/O port B bit 1 |
| Broche 28 | RB2 — I/O port B bit 2 |
| Broche 29 | RB3 — I/O port B bit 3 |
| Broche 30 | RB4 — I/O port B bit 4 |
| Broche 31 | RB5 — I/O port B bit 5 |
| Broche 32 | RB6 — I/O port B bit 6 |
| Broche 33 | RB7 — I/O port B bit 7 |
| Broche 34 | RC0 — I/O port C bit 0 |
| Broche 35 | RC1 — I/O port C bit 1 |
| Broche 36 | RC2 — I/O port C bit 2 |
| Broche 37 | RC3 — I/O port C bit 3 |
| Broche 38 | RC4 — I/O port C bit 4 |
| Broche 39 | RC5 — I/O port C bit 5 |
| Broche 40 | RC6 — I/O port C bit 6 |
| Broche 41 | RC7 — I/O port C bit 7 |
| Broche 42 | RD0 — I/O port D bit 0 |
| Broche 43 | RD1 — I/O port D bit 1 |
| Broche 44 | RD2 — I/O port D bit 2 |
| Broche 45 | RD3 — I/O port D bit 3 |
| Broche 46 | RD4 — I/O port D bit 4 |
| Broche 47 | RD5 — I/O port D bit 5 |
| Broche 48 | RD6 — I/O port D bit 6 |
| Broche 49 | RD7 — I/O port D bit 7 |
| Broche 50 | RE0 — I/O port E bit 0 |
| Broche 51 | RE1 — I/O port E bit 1 |
| Broche 52 | RE2 — I/O port E bit 2 |
| Broche 53 | RE3 — I/O port E bit 3 |
| Broche 54 | RE4 — I/O port E bit 4 |
| Broche 55 | RE5 — I/O port E bit 5 |
| Broche 56 | RE6 — I/O port E bit 6 |
| Broche 57 | RE7 — I/O port E bit 7 |
| Broche 58 | RF0 — I/O port F bit 0 |
| Broche 59 | RF1 — I/O port F bit 1 |
| Broche 60 | RF2 — I/O port F bit 2 |
| Broche 61 | RF3 — I/O port F bit 3 |
| Broche 62 | RF4 — I/O port F bit 4 |
| Broche 63 | RF5 — I/O port F bit 5 |
| Broche 64 | RF6 — I/O port F bit 6 |
| Broche 65 | RF7 — I/O port F bit 7 |
| Broche 66 | RG0 — I/O port G bit 0 |
| Broche 67 | RG1 — I/O port G bit 1 |
| Broche 68 | RG2 — I/O port G bit 2 |
| Broche 69 | RG3 — I/O port G bit 3 |
| Broche 70 | AVDD — Analog supply |
| Broche 71 | AVSS — Analog ground |
| Broche 72 | VDD — Core logic supply |
| Broche 73 | VSS — Ground |
| Broche 74 | C1RX — CAN1 receive |
| Broche 75 | C1TX — CAN1 transmit |
| Broche 76 | U1RX — UART1 receive |
| Broche 77 | U1TX — UART1 transmit |
| Broche 78 | PWM1H — PWM1 high-side output |
| Broche 79 | PWM1L — PWM1 low-side output |
| Broche 80 | NC — Not connected (per datasheet) |
Applications typiques
DSPIC30F6013T-30I/PF convient pour 6 applications: BLDC / PMSM Motor Control, Digital Power Conversion (UPS / Solar Inverter), Automotive Body and Chassis Controllers, Audio Signal Processing, Industrial Sensor Signal Conditioning, Uninterruptible Power Supply (UPS) Controllers.
BLDC / PMSM Motor Control
The DSPIC30F6013T-30I/PF's 30 MIPS DSP engine, motor-control PWM module, and 12-bit ADC make it ideal for brushless DC and permanent-magnet synchronous motor drives. Its single-cycle 16x16 MAC supports field-oriented control (FOC) algorithms with torque ripple below 2%. The 80-pin TQFP exposes sufficient PWM channels and ADC inputs for direct three-phase inverter drive without external logic. Engineers implementing sensorless FOC benefit from the DSP engine's fractional arithmetic for Park/Clarke transforms and PI loop execution under 10 us per control cycle. The 6 KB RAM accommodates state estimators and reference frames. Compared with general-purpose MCUs lacking DSP extensions, the dsPIC30F reduces CPU loading by 40-60% in motor-control firmware.
Recommandé
Digital Power Conversion (UPS / Solar Inverter)
For digital power supplies and solar inverter MPPT algorithms, the DSPIC30F6013T-30I/PF combines DSP throughput with MCU determinism. The 30 MIPS engine executes voltage-mode and current-mode control loops at 50-100 kHz switching frequencies. The 12-bit ADC samples feedback signals at sub-microsecond conversion rates, and the PWM module generates phase-shifted gate-drive waveforms for bridgeless PFC topologies. The 132 KB Flash accommodates state-space control firmware and lookup tables for MPPT and THD optimization. Operating from 2.5V-5.5V, the device interfaces directly to 3.3V gate drivers and 5V analog front-ends. The 6 KB RAM holds ADC sample buffers and PID state variables.
Recommandé
Automotive Body and Chassis Controllers
The DSPIC30F6013T-30I/PF's industrial temperature range (-40C to +85C), CAN peripheral, and DSP capability suit automotive body controllers for window lifts, seat positioners, and HVAC blowers. The 30 MIPS throughput executes multiple LIN/CAN message handlers alongside motor-control routines without CPU starvation. The 80-pin TQFP provides sufficient I/O for sensor interfacing and H-bridge driver control. Automotive applications benefit from the DSP engine for sensor fusion in chassis control units, where accelerometer and gyroscope data are filtered in real time. Although AEC-Q100 qualification is not stated, the device's industrial temperature grade and robust Flash memory support under-hood and body-module deployments.
Recommandé
Audio Signal Processing
The DSPIC30F6013T-30I/PF delivers DSP throughput for low-cost audio effects processors, equalizers, and active noise-cancellation front-ends. Its single-cycle MAC executes biquad filters and FFTs at CD-quality sample rates (44.1 kHz). The 132 KB Flash stores filter coefficients and preset tables, while 6 KB RAM buffers audio frames. The I2S-compatible SPI peripheral interfaces to common audio codecs. Compared with dedicated audio DSPs, the dsPIC30F trades absolute throughput for integrated MCU peripherals and lower BOM cost. Typical use cases include karaoke mixers, hearing-aid pre-processing, and guitar multi-effects pedals.
Recommandé
Industrial Sensor Signal Conditioning
For industrial process control, the DSPIC30F6013T-30I/PF digitizes and filters signals from strain gauges, thermocouples, and pressure sensors. Its 12-bit ADC (up to 16 channels) multiplexes sensor inputs, and the DSP engine implements digital IIR filters with 60 dB stopband attenuation. The 2.5V-5.5V supply range supports 4-20 mA loop-powered transmitters and 24V industrial buses via external regulators. UART/SPI/CAN peripherals connect to PLC backplanes and industrial Ethernet gateways. The 132 KB Flash stores calibration constants and linearization tables for thermocouple cold-junction compensation.
Recommandé
Uninterruptible Power Supply (UPS) Controllers
The DSPIC30F6013T-30I/PF's DSP engine excels in UPS digital control loops, where it computes inverter output voltage regulation, battery charging profiles, and load-sharing algorithms in real time. The motor-control PWM module generates sine-triangle PWM with dead-time insertion for IGBT gate drives. The 80-pin TQFP provides dedicated pins for grid synchronization, battery management, and bypass switching. The 6 KB RAM holds grid-cycle state variables, while 132 KB Flash stores inverter firmware and battery chemistry profiles. Operating from 2.5V-5.5V, the device pairs with external gate drivers and isolated ADC front-ends.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DSPIC30F6013T-30I/PF — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DSPIC30F6014T-30I/PF | DSPIC30F6013AT-30I/PT | DSPIC30F6013A-30I/PF | DSPIC30F6012AT-30I/PF |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-pin TQFP (14x14) | 80-pin TQFP (14x14) - same | 80-pin TQFP (14x14) - same | 80-pin TQFP (14x14) - same | 80-pin TQFP (14x14) - same |
| Flash Memory | 132 KB | 132 KB | 132 KB | 132 KB | 144 KB |
| RAM | 6 KB | 6 KB | 6 KB | 6 KB | 8 KB |
| CPU Speed | 30 MIPS at 30 MHz | 30 MIPS at 30 MHz | 30 MIPS at 30 MHz | 30 MIPS at 30 MHz | 30 MIPS at 30 MHz |
| CAN Peripheral | Yes (1x CAN) | Yes (1x CAN) | Yes (1x CAN) | Yes (1x CAN) | Yes (1x CAN) |
| Lifecycle Status | Obsolete | Obsolete | Active | Active | Active |
| Operating Voltage | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
| RoHS Compliance | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant |
Principaux différenciateurs
- Single-cycle 16x16 MAC DSP engine (vs DSPIC30F4013-20I/ML)
- 132 KB Flash with 80-pin TQFP package (vs DSPIC30F5011-30I/PT)
- Active lifecycle silicon A revision available (vs DSPIC30F6013T-30I/PF (this part))
Notes de conception
The 80-pin TQFP package has a typical theta_JA of approximately 45-55 C/W on a standard 4-layer JEDEC test board. At full 30 MIPS operation with all peripherals active, internal dissipation is approximately 0.5-0.8 W. For motor-control applications driving high-current IGBTs via external gate drivers, ensure the PCB provides adequate copper pour (at least 1 sq inch) connected to the thermal pad or VSS pins to keep junction temperature below 125 C. In enclosed industrial enclosures, consider airflow or heat-sinking the inverter heatsink shared with the DSC thermal mass.
Place 100 nF decoupling capacitors as close as possible to each VDD/VSS pair (typically 4-6 pairs on the 80-pin TQFP). Add a 10 uF bulk capacitor near the AVDD pin for ADC reference stability. Keep analog input traces (AN0-AN15) away from PWM switching traces and clock signals to minimize coupling. For motor-control applications, route the three-phase PWM outputs (PWM1H/L through PWM3H/L) symmetrically with equal-length traces to maintain switching timing alignment.
When migrating code from DSPIC30F6013 to DSPIC30F6013A silicon revision, consult the device errata document - the 'A' revision fixes several PWM and ADC peripheral bugs but may introduce silicon ID changes that affect bootloader code. Do not assume Q15 fractional arithmetic without configuring the CORCON register appropriately. When using the CAN peripheral, configure the CAN I/O pins via the PPS (Peripheral Pin Select) module before enabling the CAN module, or the device may enter an undefined state.
The DSPIC30F6013T-30I/PF's 30 MIPS operation generates fast-edge signals on PWM outputs (rise times <10 ns). Use series damping resistors (10-33 ohm) on PWM outputs driving long cables or external gate drivers to limit ringing. For ADC inputs, add RC low-pass filters (1 kohm + 100 pF) to reject switching noise from PWM traces crossing analog signal paths. Verify signal integrity with oscilloscope measurements at full load before finalizing PCB layout.
Informations de conformité
ROHS3 Compliant per Microchip USA product page. AEC-Q100 qualification not stated for this part; AEC-Q100 grade variants may exist in the dsPIC33 family for automotive applications. REACH compliance inferred from Microchip's standard compliance statements.
