DSPIC33EP256GP506T-E/PT - 16-bit 60 MIPS DSC 256KB | Microchip
Référence : DSPIC33EP256GP506T-E/PT ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $7.35 | $7,35 |
| 10 | $6.72 | $67,20 |
| 100 | $5.94 | $594,00 |
| 500 | $5.31 | $2 655,00 |
| 1 000 | $4.86 | $4 860,00 |
DSPIC33EP256GP506T-E/PT Présentation
A digital signal controller combines the architecture of a microcontroller (MCU) with the computational core of a digital signal processor (DSP). In the power-management hierarchy of embedded systems, the dsPIC33EP family sits between general-purpose 16-bit MCUs and dedicated DSPs, offering single-cycle MAC instructions, hardware division, and barrel shifting alongside conventional peripherals, making it ideal for control loops that need both deterministic timing and mathematical throughput.
Key differentiating features of the dsPIC33EP GP family include up to 70 MIPS capable core (this -E grade part runs at 60 MIPS), superior ADC performance, CANbus connectivity, a Charge Time Measurement Unit (CTMU), integrated analog comparators, and a Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. Connectivity spans CANbus, I2C, IrDA, LINbus, SPI, and UART/USART, enabling multi-bus industrial nodes on a single chip.
Technically, the device uses a modified Harvard 16-bit architecture with 24-bit instruction words, supporting DSP-style addressing and deterministic interrupt latency. The wide -40C to +125C extended temperature range and AEC-Q100 qualification make the -E suffix variant suitable for automotive and harsh industrial environments where standard -I grade parts (up to 85C ambient) are insufficient.
Typical applications include automotive body and control modules, industrial motor control and digital power conversion, sensor fusion and data acquisition nodes, and general-purpose embedded control requiring CAN networking. The rich peripheral set allows one device to close high-rate control loops while servicing communication stacks.
Design consideration: this -E/PT grade part is specified for extended temperature; derate maximum operating frequency and confirm thermal budget in enclosed, high-temperature enclosures since the 64-TQFP relies on PCB copper for heat dissipation.
This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet, with all pricing as of 2026-09-24.
Alternatives de remplacement direct pour DSPIC33EP256GP506T-E/PT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec DSPIC33EP256GP506T-E/PT (même facteur de forme et même empreinte) — différant par Operating Temperature, Package, RAM, Core Architecture, Packaging.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
DSPIC33EP256GP506-I/PT
✅ Remplacement direct✓ En stock
$4.65 / unité
Voir la fiche technique →DSPIC33EP256GP506T-I/PT
✅ Remplacement direct✓ En stock
Contactez-nous pour le prix
Voir la fiche technique →DSPIC33EP256GP504-I/PT
✅ Remplacement direct✓ En stock
$3.68 / unité
Voir la fiche technique →DSPIC33EP256GP506T-I/MR
✅ Remplacement direct✓ En stock
$4.15 / unité
Voir la fiche technique →DSPIC33EP512GP506-I/PT
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
DSPIC33EP128GP506-I/PT
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
DSPIC33EP256GP506T-E/PT Valeurs maximales et caractéristiques électriques
| Core | 16-bit dsPIC33E DSC |
| Max CPU Speed | 60 MIPs |
| Program Memory (FLASH) | 256KB (85.5K x 24) |
| RAM | 16KB |
| Tension d'alimentation | 3.3 V |
| Boîtier | 64-TQFP (10x10 mm) |
| Température de fonctionnement | -40C to +125C (Extended, -E grade) |
| Type de montage | Surface Mount |
| Connectivity | CANbus, I2C, IrDA, LINbus, SPI, UART/USART |
| Qualification | AEC-Q100 qualified, Automotive |
| Core Technology | CMOS |
| Special Peripherals | CAN, CTMU, Comparators, Op Amps, PTG |
| Terminal Pitch | 0.5 mm |
| Series | dsPIC 33EP |
| Packaging | Tape & Reel (T suffix) |
Configuration des broches de DSPIC33EP256GP506T-E/PT
| Broche 1 | MCLR — Master clear reset (active low) / programming voltage input |
| Broche 2 | AN0/VREF+/CN0/RB0 — Analog input 0 / positive voltage reference / change notification / port B |
| Broche 3 | AN1/VREF-/CN1/RB1 — Analog input 1 / negative voltage reference / change notification / port B |
| Broche 4 | AN2/SS1/CN2/RB2 — Analog input 2 / SPI slave select 1 / CN / port B |
| Broche 5 | AN3/INDX/CN3/RB3 — Analog input 3 / encoder index / CN / port B |
| Broche 6 | AN4/QEA/IC7/CN4/RB4 — Analog input 4 / quadrature A / input capture 7 / CN / port B |
| Broche 7 | AN5/QEB/IC8/CN5/RB5 — Analog input 5 / quadrature B / input capture 8 / CN / port B |
| Broche 8 | AN6/OCFA/RB6 — Analog input 6 / output compare fault A / port B |
| Broche 9 | AN7/RB7 — Analog input 7 / port B |
| Broche 10 | AN8/RB8 — Analog input 8 / port B |
| Broche 11 | AN9/RB9 — Analog input 9 / port B |
| Broche 12 | AN10/RB10 — Analog input 10 / port B |
| Broche 13 | AN11/RB11 — Analog input 11 / port B |
| Broche 14 | VSS — Ground reference |
| Broche 15 | VDD — 3.3V power supply |
| Broche 16 | AN12/RB12 — Analog input 12 / port B |
| Broche 17 | AN13/RB13 — Analog input 13 / port B |
| Broche 18 | AN14/RB14 — Analog input 14 / port B |
| Broche 19 | AN15/OCFB/RB15 — Analog input 15 / output compare fault B / port B |
| Broche 20 | PGD3/U1TX/SDO2/RF3 — Programming data 3 / UART1 TX / SPI2 data out / port F |
| Broche 21 | PGC3/U1RX/SDI2/RF2 — Programming clock 3 / UART1 RX / SPI2 data in / port F |
| Broche 22 | TCK/RA0 — JTAG test clock / port A |
| Broche 23 | TDO/RA1 — JTAG test data out / port A |
| Broche 24 | TMS/RA2 — JTAG test mode select / port A |
| Broche 25 | OSC1/CLKI/RC12 — Oscillator crystal input / external clock in / port C |
| Broche 26 | OSC2/CLKO/RC15 — Oscillator crystal output / clock out / port C |
| Broche 27 | RC1/T2CK — Port C / timer 2 external clock |
| Broche 28 | RC3/T5CK — Port C / timer 5 external clock |
| Broche 29 | RC4/U1TX — Port C / UART1 TX (PPS) |
| Broche 30 | SOSCI/CN1/RC13 — Secondary oscillator input / CN / port C |
| Broche 31 | SOSCO/T1CK/CN0/RC14 — Secondary oscillator output / timer 1 clock / CN / port C |
| Broche 32 | VDD — 3.3V power supply |
| Broche 33 | VSS — Ground reference |
| Broche 34 | RD8/PMD0 — Port D / parallel master port data 0 |
| Broche 35 | RD9/PMD1 — Port D / PMP data 1 |
| Broche 36 | RD10/PMD2 — Port D / PMP data 2 |
| Broche 37 | RD11/PMD3 — Port D / PMP data 3 |
| Broche 38 | RD0/PMBE — Port D / PMP byte enable |
| Broche 39 | RD1/PMCS1 — Port D / PMP chip select 1 |
| Broche 40 | RD2/PMCS2 — Port D / PMP chip select 2 |
| Broche 41 | RD3/PMWR — Port D / PMP write strobe |
| Broche 42 | RD4/PMRD — Port D / PMP read strobe |
| Broche 43 | RD5 — Port D general purpose I/O |
| Broche 44 | RD6 — Port D general purpose I/O |
| Broche 45 | RD7 — Port D general purpose I/O |
| Broche 46 | RG8 — Port G general purpose I/O |
| Broche 47 | RG9 — Port G general purpose I/O |
| Broche 48 | VSS — Ground reference |
| Broche 49 | VDD — 3.3V power supply |
| Broche 50 | RF12 — Port F general purpose I/O (PPS capable) |
| Broche 51 | RF13 — Port F general purpose I/O (PPS capable) |
| Broche 52 | RF4 — Port F general purpose I/O (PPS capable) |
| Broche 53 | RF5 — Port F general purpose I/O (PPS capable) |
| Broche 54 | AVDD — Analog power supply (3.3V) |
| Broche 55 | AVSS — Analog ground |
| Broche 56 | RF6 — Port F general purpose I/O (PPS capable) |
| Broche 57 | RF7 — Port F general purpose I/O (PPS capable) |
| Broche 58 | RE0/PMCS1 — Port E / PMP chip select 1 |
| Broche 59 | RE1/PMCS2 — Port E / PMP chip select 2 |
| Broche 60 | RE2/PMRD — Port E / PMP read strobe |
| Broche 61 | RE3/PMWR — Port E / PMP write strobe |
| Broche 62 | RE4 — Port E general purpose I/O |
| Broche 63 | RE5 — Port E general purpose I/O |
| Broche 64 | RE6/EMUD1 — Port E / emulation data 1 |
Applications typiques
DSPIC33EP256GP506T-E/PT convient pour 6 applications: Automotive Control Modules, Industrial Motor Control, Digital Power Conversion, Data Acquisition and Sensor Nodes, Audio and Communication Gateways, Consumer Appliance Control.
Automotive Control Modules
The DSPIC33EP256GP506T-E/PT is AEC-Q100 qualified with a -40C to +125C extended operating range, exactly matching underhood and body-electronics temperature envelopes. Its 60 MIPS 16-bit core closes deterministic control loops while the ECAN module handles CAN 2.0B networking with hardware message objects, and LINbus-capable UARTs cover low-cost subnetworks. In a body control module, the device can sequence relay and LED loads, run diagnostics via the CTMU, and service the CAN bus simultaneously from one chip. The 256KB FLASH accommodates UDS/OBD-style firmware stacks with room for calibration tables. Thermal design should confirm junction temperature stays within limits at 125C ambient, typically by maximizing PCB copper under the exposed thermal footprint of the 64-TQFP.
Recommandé
Industrial Motor Control
Digital motor control demands fast ADC sampling synchronized to PWM events - precisely what the dsPIC33EP GP family's Peripheral Trigger Generator (PTG) and high-speed ADC enable. The 60 MIPS core executes single-cycle MAC instructions for field-oriented control (FOC) math on PMSM and BLDC motors, while hardware comparators provide cycle-level overcurrent protection without CPU intervention. The 64-TQFP device offers enough PWM outputs for three-phase bridges with complementary or independent modes. Using this -E grade in industrial drives adds margin for hot control cabinets approaching 85C-100C ambient. Implementation typically pairs the DSC with a three-phase gate driver and current-sense amplifiers; the integrated op amps can condition low-side shunt signals, reducing external component count by two to three amplifiers per axis.
Recommandé
Digital Power Conversion
Switching power supplies, LLC converters, and solar micro-inverters require control-loop update rates above 100 kHz with low-jitter PWM. The dsPIC33EP's 60 MIPS throughput, deterministic interrupt latency, and DSP multiply-accumulate instructions sustain proportional-integral compensation loops at these rates while hardware comparators trip PWM outputs within nanoseconds on fault conditions. The PTG autonomously sequences ADC triggers against PWM phase, keeping sampling jitter minimal without loading the CPU. The 256KB FLASH holds multiple converter topologies and commissioning code. This extended-temperature -E variant suits power stages inside sealed industrial enclosures. Design attention should go to ADC input filtering and using the device's high-resolution phase of PWM at light loads to maintain efficiency across the load range.
Recommandé
Data Acquisition and Sensor Nodes
The dsPIC33EP256GP506's fast 12-bit ADC with multiple sample-and-hold channels, CTMU for capacitive or time-of-flight measurement, and integrated op amps make it a compact analog front end for industrial sensing nodes. The 60 MIPS core applies DSP filtering (FIR/IIR) to raw samples in real time, offloading host processors, while SPI and I2C links stream processed data upward and CANbus integrates the node into factory networks. The extended -40C to +125C rating suits sensors mounted on motors, pumps, and outdoor enclosures. With 16KB of RAM and 256KB FLASH, the node buffers waveforms and executes embedded analysis locally. Designers should leverage the PTG to pace conversions at fixed intervals, producing timestamp-consistent data without software jitter.
Recommandé
Audio and Communication Gateways
Multi-protocol gateways bridging CAN, LIN, RS-485, and UART segments benefit from the dsPIC33EP256GP506's six connectivity peripherals (CANbus, I2C, IrDA, LINbus, SPI, UART/USART per DigiKey). The 60 MIPS core runs protocol stacks plus application routing concurrently, and the DSP engine handles audio filtering or tone generation where voice-quality signal processing is needed - the dsPIC lineage originates from DSP architectures. The 256KB FLASH stores multiple protocol firmware images with field-updatable regions. Extended temperature qualification allows deployment in outdoor telecom cabinets. Implement store-and-forward buffering in the 16KB RAM with flow control, and use the Peripheral Trigger Generator to pace DMA transfers between peripherals, minimizing CPU overhead in high-traffic routing scenarios.
Recommandé
Consumer Appliance Control
High-end appliances - induction cooktops, compressors, dishwashers - combine motor control, user-interface sensing, and safety monitoring in one controller. This DSC runs the compressor FOC loop with hardware-protected PWM, reads capacitive touch keys via the CTMU, and supervises temperature sensors through its ADC, eliminating a separate touch controller IC. The 64-TQFP provides generous I/O for displays, relays, and communication to cloud modules over UART. AEC-Q100 pedigree gives appliance makers conservative reliability margins even in consumer budgets. The extended -E grade tolerates hot compressor compartments where standard parts derate. Firmware should partition time-critical control interrupts from the UI task scheduler, and designers must budget the 16KB RAM carefully when adding touch-decimation libraries alongside the motor-control state machine.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DSPIC33EP256GP506T-E/PT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DSPIC33EP256GP506-I/PT | DSPIC33EP256GP506T-I/PT | DSPIC33EP256GP504-I/PT | DSPIC33EP256GP506T-I/MR | DSPIC33EP512GP506-I/PT |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (10x10) | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-QFN - different land pattern | 64-TQFP (10x10) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| FLASH Program Memory | 256KB | 256KB | 256KB | 256KB | 256KB | 512KB |
| Core Speed | 60 MIPs | 60 MIPs (up to 70 MIPs family capability) | 60 MIPs | 60 MIPs | 60 MIPs | 60 MIPs |
| Temperature Range | -40C to +125C (Extended, -E) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| Connectivity | CAN, I2C, IrDA, LIN, SPI, UART | CAN, I2C, IrDA, LIN, SPI, UART | CAN, I2C, IrDA, LIN, SPI, UART | CAN, I2C, IrDA, LIN, SPI, UART | CAN, I2C, IrDA, LIN, SPI, UART | CAN, I2C, IrDA, LIN, SPI, UART |
| Typical Role vs This Part | Extended-temp general purpose DSC | Cost-optimized industrial substitute | Reel-priced industrial substitute | Reduced-RAM/peripheral variant | QFN option for compact PCBs | Double memory for code growth |
Principaux différenciateurs
- Extended -40C to +125C automotive-grade operation (vs DSPIC33EP256GP506T-I/PT)
- Full general-purpose peripheral set with op amps, CTMU, and PTG (vs DSPIC33EP256MC506-I/PT)
- Tape-and-reel (T suffix) volume sourcing (vs DSPIC33EP256GP506-I/PT)
Notes de conception
Provide a clean 3.3V rail with 0.1uF ceramic decoupling at every VDD pin (pins 15, 32, 49) plus bulk 10uF near the device. Keep AVDD (pin 54) on a separate filtered supply - a ferrite bead plus 1uF/0.1uF network from the digital rail significantly improves ADC accuracy. Connect AVSS to a quiet analog ground island. Estimated: at 60 MIPS with peripherals active, core current is typically in the tens of mA range; confirm exact figures in the DS70000657J electrical characteristics tables before finalizing regulator sizing.
The 64-TQFP (10x10 mm, 0.5 mm pitch) requires careful escape routing: use 0.2 mm trace width with 0.2-0.25 mm spacing under the body. Place the ICSP programming header (MCLR, PGD, PGC, VDD, GND) close to pins 1, 20 and 21 with series 100-ohm resistors on PGD/PGC to isolate programming from application loads. Reserve the OSC1/OSC2 pins with short crystal traces and local ground guard if using the primary oscillator. At 125C ambient, maximize 2-oz copper planes under the package to conduct heat away.
Do not confuse temperature grades: this -E/PT part is rated -40C to +125C, but its industrial -I siblings are limited to +85C - substituting an -I part during a shortage silently voids the extended-temperature margin. Also, MCLR must not be driven above 3.3V during normal operation (higher voltages are only valid during programming). Finally, review Peripheral Pin Select (PPS) mappings in firmware before hardware reuse - unlike earlier dsPIC families, UART/SPI/other digital functions are software-routable and a wrong PPS table is a common bring-up failure.
Informations de conformité
AEC-Q100 qualified and classified Automotive per DigiKey and Microchip USA listings. RoHS/lead-free per DigiKey listing; REACH and halogen-free status not stated in provided data.
