DSPIC33EP256GP506T-E/PT - 16-bit 60 MIPS DSC 256KB | Microchip
Артикул: DSPIC33EP256GP506T-E/PT ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $7.35 | $7,35 |
| 10 | $6.72 | $67,20 |
| 100 | $5.94 | $594,00 |
| 500 | $5.31 | $2.655,00 |
| 1.000 | $4.86 | $4.860,00 |
DSPIC33EP256GP506T-E/PT Обзор
A digital signal controller combines the architecture of a microcontroller (MCU) with the computational core of a digital signal processor (DSP). In the power-management hierarchy of embedded systems, the dsPIC33EP family sits between general-purpose 16-bit MCUs and dedicated DSPs, offering single-cycle MAC instructions, hardware division, and barrel shifting alongside conventional peripherals, making it ideal for control loops that need both deterministic timing and mathematical throughput.
Key differentiating features of the dsPIC33EP GP family include up to 70 MIPS capable core (this -E grade part runs at 60 MIPS), superior ADC performance, CANbus connectivity, a Charge Time Measurement Unit (CTMU), integrated analog comparators, and a Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. Connectivity spans CANbus, I2C, IrDA, LINbus, SPI, and UART/USART, enabling multi-bus industrial nodes on a single chip.
Technically, the device uses a modified Harvard 16-bit architecture with 24-bit instruction words, supporting DSP-style addressing and deterministic interrupt latency. The wide -40C to +125C extended temperature range and AEC-Q100 qualification make the -E suffix variant suitable for automotive and harsh industrial environments where standard -I grade parts (up to 85C ambient) are insufficient.
Typical applications include automotive body and control modules, industrial motor control and digital power conversion, sensor fusion and data acquisition nodes, and general-purpose embedded control requiring CAN networking. The rich peripheral set allows one device to close high-rate control loops while servicing communication stacks.
Design consideration: this -E/PT grade part is specified for extended temperature; derate maximum operating frequency and confirm thermal budget in enclosed, high-temperature enclosures since the 64-TQFP relies on PCB copper for heat dissipation.
This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet, with all pricing as of 2026-09-24.
Аналоги без доработки для DSPIC33EP256GP506T-E/PT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DSPIC33EP256GP506T-E/PT (тот же форм-фактор и посадочное место) — отличается по Operating Temperature, Package, RAM, Core Architecture, Packaging.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
DSPIC33EP256GP506-I/PT
✅ Прямая замена✓ В наличии
$4.65 / шт.
Открыть даташит →DSPIC33EP256GP506T-I/PT
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →DSPIC33EP256GP504-I/PT
✅ Прямая замена✓ В наличии
$3.68 / шт.
Открыть даташит →DSPIC33EP256GP506T-I/MR
✅ Прямая замена✓ В наличии
$4.15 / шт.
Открыть даташит →DSPIC33EP512GP506-I/PT
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP128GP506-I/PT
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
DSPIC33EP256GP506T-E/PT Максимальные параметры и электрические характеристики
| Core | 16-bit dsPIC33E DSC |
| Max CPU Speed | 60 MIPs |
| Program Memory (FLASH) | 256KB (85.5K x 24) |
| RAM | 16KB |
| Напряжение питания | 3.3 V |
| Корпус | 64-TQFP (10x10 mm) |
| Рабочая температура | -40C to +125C (Extended, -E grade) |
| Тип монтажа | Surface Mount |
| Connectivity | CANbus, I2C, IrDA, LINbus, SPI, UART/USART |
| Qualification | AEC-Q100 qualified, Automotive |
| Core Technology | CMOS |
| Special Peripherals | CAN, CTMU, Comparators, Op Amps, PTG |
| Terminal Pitch | 0.5 mm |
| Series | dsPIC 33EP |
| Packaging | Tape & Reel (T suffix) |
Конфигурация выводов DSPIC33EP256GP506T-E/PT
| Контакт 1 | MCLR — Master clear reset (active low) / programming voltage input |
| Контакт 2 | AN0/VREF+/CN0/RB0 — Analog input 0 / positive voltage reference / change notification / port B |
| Контакт 3 | AN1/VREF-/CN1/RB1 — Analog input 1 / negative voltage reference / change notification / port B |
| Контакт 4 | AN2/SS1/CN2/RB2 — Analog input 2 / SPI slave select 1 / CN / port B |
| Контакт 5 | AN3/INDX/CN3/RB3 — Analog input 3 / encoder index / CN / port B |
| Контакт 6 | AN4/QEA/IC7/CN4/RB4 — Analog input 4 / quadrature A / input capture 7 / CN / port B |
| Контакт 7 | AN5/QEB/IC8/CN5/RB5 — Analog input 5 / quadrature B / input capture 8 / CN / port B |
| Контакт 8 | AN6/OCFA/RB6 — Analog input 6 / output compare fault A / port B |
| Контакт 9 | AN7/RB7 — Analog input 7 / port B |
| Контакт 10 | AN8/RB8 — Analog input 8 / port B |
| Контакт 11 | AN9/RB9 — Analog input 9 / port B |
| Контакт 12 | AN10/RB10 — Analog input 10 / port B |
| Контакт 13 | AN11/RB11 — Analog input 11 / port B |
| Контакт 14 | VSS — Ground reference |
| Контакт 15 | VDD — 3.3V power supply |
| Контакт 16 | AN12/RB12 — Analog input 12 / port B |
| Контакт 17 | AN13/RB13 — Analog input 13 / port B |
| Контакт 18 | AN14/RB14 — Analog input 14 / port B |
| Контакт 19 | AN15/OCFB/RB15 — Analog input 15 / output compare fault B / port B |
| Контакт 20 | PGD3/U1TX/SDO2/RF3 — Programming data 3 / UART1 TX / SPI2 data out / port F |
| Контакт 21 | PGC3/U1RX/SDI2/RF2 — Programming clock 3 / UART1 RX / SPI2 data in / port F |
| Контакт 22 | TCK/RA0 — JTAG test clock / port A |
| Контакт 23 | TDO/RA1 — JTAG test data out / port A |
| Контакт 24 | TMS/RA2 — JTAG test mode select / port A |
| Контакт 25 | OSC1/CLKI/RC12 — Oscillator crystal input / external clock in / port C |
| Контакт 26 | OSC2/CLKO/RC15 — Oscillator crystal output / clock out / port C |
| Контакт 27 | RC1/T2CK — Port C / timer 2 external clock |
| Контакт 28 | RC3/T5CK — Port C / timer 5 external clock |
| Контакт 29 | RC4/U1TX — Port C / UART1 TX (PPS) |
| Контакт 30 | SOSCI/CN1/RC13 — Secondary oscillator input / CN / port C |
| Контакт 31 | SOSCO/T1CK/CN0/RC14 — Secondary oscillator output / timer 1 clock / CN / port C |
| Контакт 32 | VDD — 3.3V power supply |
| Контакт 33 | VSS — Ground reference |
| Контакт 34 | RD8/PMD0 — Port D / parallel master port data 0 |
| Контакт 35 | RD9/PMD1 — Port D / PMP data 1 |
| Контакт 36 | RD10/PMD2 — Port D / PMP data 2 |
| Контакт 37 | RD11/PMD3 — Port D / PMP data 3 |
| Контакт 38 | RD0/PMBE — Port D / PMP byte enable |
| Контакт 39 | RD1/PMCS1 — Port D / PMP chip select 1 |
| Контакт 40 | RD2/PMCS2 — Port D / PMP chip select 2 |
| Контакт 41 | RD3/PMWR — Port D / PMP write strobe |
| Контакт 42 | RD4/PMRD — Port D / PMP read strobe |
| Контакт 43 | RD5 — Port D general purpose I/O |
| Контакт 44 | RD6 — Port D general purpose I/O |
| Контакт 45 | RD7 — Port D general purpose I/O |
| Контакт 46 | RG8 — Port G general purpose I/O |
| Контакт 47 | RG9 — Port G general purpose I/O |
| Контакт 48 | VSS — Ground reference |
| Контакт 49 | VDD — 3.3V power supply |
| Контакт 50 | RF12 — Port F general purpose I/O (PPS capable) |
| Контакт 51 | RF13 — Port F general purpose I/O (PPS capable) |
| Контакт 52 | RF4 — Port F general purpose I/O (PPS capable) |
| Контакт 53 | RF5 — Port F general purpose I/O (PPS capable) |
| Контакт 54 | AVDD — Analog power supply (3.3V) |
| Контакт 55 | AVSS — Analog ground |
| Контакт 56 | RF6 — Port F general purpose I/O (PPS capable) |
| Контакт 57 | RF7 — Port F general purpose I/O (PPS capable) |
| Контакт 58 | RE0/PMCS1 — Port E / PMP chip select 1 |
| Контакт 59 | RE1/PMCS2 — Port E / PMP chip select 2 |
| Контакт 60 | RE2/PMRD — Port E / PMP read strobe |
| Контакт 61 | RE3/PMWR — Port E / PMP write strobe |
| Контакт 62 | RE4 — Port E general purpose I/O |
| Контакт 63 | RE5 — Port E general purpose I/O |
| Контакт 64 | RE6/EMUD1 — Port E / emulation data 1 |
Типичное применение
DSPIC33EP256GP506T-E/PT подходит для 6 применениеs: Automotive Control Modules, Industrial Motor Control, Digital Power Conversion, Data Acquisition and Sensor Nodes, Audio and Communication Gateways, Consumer Appliance Control.
Automotive Control Modules
The DSPIC33EP256GP506T-E/PT is AEC-Q100 qualified with a -40C to +125C extended operating range, exactly matching underhood and body-electronics temperature envelopes. Its 60 MIPS 16-bit core closes deterministic control loops while the ECAN module handles CAN 2.0B networking with hardware message objects, and LINbus-capable UARTs cover low-cost subnetworks. In a body control module, the device can sequence relay and LED loads, run diagnostics via the CTMU, and service the CAN bus simultaneously from one chip. The 256KB FLASH accommodates UDS/OBD-style firmware stacks with room for calibration tables. Thermal design should confirm junction temperature stays within limits at 125C ambient, typically by maximizing PCB copper under the exposed thermal footprint of the 64-TQFP.
Рекомендуется
Industrial Motor Control
Digital motor control demands fast ADC sampling synchronized to PWM events - precisely what the dsPIC33EP GP family's Peripheral Trigger Generator (PTG) and high-speed ADC enable. The 60 MIPS core executes single-cycle MAC instructions for field-oriented control (FOC) math on PMSM and BLDC motors, while hardware comparators provide cycle-level overcurrent protection without CPU intervention. The 64-TQFP device offers enough PWM outputs for three-phase bridges with complementary or independent modes. Using this -E grade in industrial drives adds margin for hot control cabinets approaching 85C-100C ambient. Implementation typically pairs the DSC with a three-phase gate driver and current-sense amplifiers; the integrated op amps can condition low-side shunt signals, reducing external component count by two to three amplifiers per axis.
Рекомендуется
Digital Power Conversion
Switching power supplies, LLC converters, and solar micro-inverters require control-loop update rates above 100 kHz with low-jitter PWM. The dsPIC33EP's 60 MIPS throughput, deterministic interrupt latency, and DSP multiply-accumulate instructions sustain proportional-integral compensation loops at these rates while hardware comparators trip PWM outputs within nanoseconds on fault conditions. The PTG autonomously sequences ADC triggers against PWM phase, keeping sampling jitter minimal without loading the CPU. The 256KB FLASH holds multiple converter topologies and commissioning code. This extended-temperature -E variant suits power stages inside sealed industrial enclosures. Design attention should go to ADC input filtering and using the device's high-resolution phase of PWM at light loads to maintain efficiency across the load range.
Рекомендуется
Data Acquisition and Sensor Nodes
The dsPIC33EP256GP506's fast 12-bit ADC with multiple sample-and-hold channels, CTMU for capacitive or time-of-flight measurement, and integrated op amps make it a compact analog front end for industrial sensing nodes. The 60 MIPS core applies DSP filtering (FIR/IIR) to raw samples in real time, offloading host processors, while SPI and I2C links stream processed data upward and CANbus integrates the node into factory networks. The extended -40C to +125C rating suits sensors mounted on motors, pumps, and outdoor enclosures. With 16KB of RAM and 256KB FLASH, the node buffers waveforms and executes embedded analysis locally. Designers should leverage the PTG to pace conversions at fixed intervals, producing timestamp-consistent data without software jitter.
Рекомендуется
Audio and Communication Gateways
Multi-protocol gateways bridging CAN, LIN, RS-485, and UART segments benefit from the dsPIC33EP256GP506's six connectivity peripherals (CANbus, I2C, IrDA, LINbus, SPI, UART/USART per DigiKey). The 60 MIPS core runs protocol stacks plus application routing concurrently, and the DSP engine handles audio filtering or tone generation where voice-quality signal processing is needed - the dsPIC lineage originates from DSP architectures. The 256KB FLASH stores multiple protocol firmware images with field-updatable regions. Extended temperature qualification allows deployment in outdoor telecom cabinets. Implement store-and-forward buffering in the 16KB RAM with flow control, and use the Peripheral Trigger Generator to pace DMA transfers between peripherals, minimizing CPU overhead in high-traffic routing scenarios.
Рекомендуется
Consumer Appliance Control
High-end appliances - induction cooktops, compressors, dishwashers - combine motor control, user-interface sensing, and safety monitoring in one controller. This DSC runs the compressor FOC loop with hardware-protected PWM, reads capacitive touch keys via the CTMU, and supervises temperature sensors through its ADC, eliminating a separate touch controller IC. The 64-TQFP provides generous I/O for displays, relays, and communication to cloud modules over UART. AEC-Q100 pedigree gives appliance makers conservative reliability margins even in consumer budgets. The extended -E grade tolerates hot compressor compartments where standard parts derate. Firmware should partition time-critical control interrupts from the UI task scheduler, and designers must budget the 16KB RAM carefully when adding touch-decimation libraries alongside the motor-control state machine.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DSPIC33EP256GP506T-E/PT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DSPIC33EP256GP506-I/PT | DSPIC33EP256GP506T-I/PT | DSPIC33EP256GP504-I/PT | DSPIC33EP256GP506T-I/MR | DSPIC33EP512GP506-I/PT |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (10x10) | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-QFN - different land pattern | 64-TQFP (10x10) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| FLASH Program Memory | 256KB | 256KB | 256KB | 256KB | 256KB | 512KB |
| Core Speed | 60 MIPs | 60 MIPs (up to 70 MIPs family capability) | 60 MIPs | 60 MIPs | 60 MIPs | 60 MIPs |
| Temperature Range | -40C to +125C (Extended, -E) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| Connectivity | CAN, I2C, IrDA, LIN, SPI, UART | CAN, I2C, IrDA, LIN, SPI, UART | CAN, I2C, IrDA, LIN, SPI, UART | CAN, I2C, IrDA, LIN, SPI, UART | CAN, I2C, IrDA, LIN, SPI, UART | CAN, I2C, IrDA, LIN, SPI, UART |
| Typical Role vs This Part | Extended-temp general purpose DSC | Cost-optimized industrial substitute | Reel-priced industrial substitute | Reduced-RAM/peripheral variant | QFN option for compact PCBs | Double memory for code growth |
Ключевые отличия
- Extended -40C to +125C automotive-grade operation (против DSPIC33EP256GP506T-I/PT)
- Full general-purpose peripheral set with op amps, CTMU, and PTG (против DSPIC33EP256MC506-I/PT)
- Tape-and-reel (T suffix) volume sourcing (против DSPIC33EP256GP506-I/PT)
Заметки по проектированию
Provide a clean 3.3V rail with 0.1uF ceramic decoupling at every VDD pin (pins 15, 32, 49) plus bulk 10uF near the device. Keep AVDD (pin 54) on a separate filtered supply - a ferrite bead plus 1uF/0.1uF network from the digital rail significantly improves ADC accuracy. Connect AVSS to a quiet analog ground island. Estimated: at 60 MIPS with peripherals active, core current is typically in the tens of mA range; confirm exact figures in the DS70000657J electrical characteristics tables before finalizing regulator sizing.
The 64-TQFP (10x10 mm, 0.5 mm pitch) requires careful escape routing: use 0.2 mm trace width with 0.2-0.25 mm spacing under the body. Place the ICSP programming header (MCLR, PGD, PGC, VDD, GND) close to pins 1, 20 and 21 with series 100-ohm resistors on PGD/PGC to isolate programming from application loads. Reserve the OSC1/OSC2 pins with short crystal traces and local ground guard if using the primary oscillator. At 125C ambient, maximize 2-oz copper planes under the package to conduct heat away.
Do not confuse temperature grades: this -E/PT part is rated -40C to +125C, but its industrial -I siblings are limited to +85C - substituting an -I part during a shortage silently voids the extended-temperature margin. Also, MCLR must not be driven above 3.3V during normal operation (higher voltages are only valid during programming). Finally, review Peripheral Pin Select (PPS) mappings in firmware before hardware reuse - unlike earlier dsPIC families, UART/SPI/other digital functions are software-routable and a wrong PPS table is a common bring-up failure.
Информация о соответствии
AEC-Q100 qualified and classified Automotive per DigiKey and Microchip USA listings. RoHS/lead-free per DigiKey listing; REACH and halogen-free status not stated in provided data.
