DSPIC33EP512GM710-I/PT - 70 MIPS 16-bit DSC, 512KB Flash | Microchip
Référence : DSPIC33EP512GM710-I/PT ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $14.2 | $14,20 |
| 10 | $12.78 | $127,80 |
| 100 | $11.36 | $1 136,00 |
| 500 | $10.05 | $5 025,00 |
| 1 000 | $8.95 | $8 950,00 |
DSPIC33EP512GM710-I/PT Présentation
A digital signal controller (DSC) is a hybrid device that combines the real-time control peripherals and deterministic interrupt behavior of a microcontroller (MCU) with the single-cycle multiply-accumulate (MAC) arithmetic and barrel shifter of a digital signal processor (DSP). In the system hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP: it is a microcontroller-class device with DSP-class math throughput, used where closed-loop control must execute in microseconds. The dsPIC33E family is Microchip's third-generation 16-bit DSC platform targeting motor control, digital power conversion, and automotive sensorless field-oriented control.
Key features include 70 MIPS operation at 70 MHz, 512 KB (170K x 24-bit) flash with 48 KB RAM, 12 motor-control PWM outputs with 1 ns edge resolution, four on-chip op amps with selectable gain, 8/8 input-capture/output-compare channels, two QEI interfaces, four DMA channels, and boundary-scan (JTAG) support. The 100-pin TQFP package exposes four 12-bit ADCs and connectivity including CAN, I2C, IrDA, LIN, SPI, and UART/USART, enabling single-chip control of dual-motor or PFC-plus-motor topologies.
The device is fabricated in CMOS and uses a precision bandgap-based analog core for the integrated op amps and ADC references. The four on-chip op amps eliminate external signal-conditioning stages for current-shunt amplification in motor drives, reducing BOM count and PCB area. Boundary scan (JTAG) and four DMA channels reduce CPU overhead in data-movement-intensive control loops. The barrel shifter accelerates fixed-point DSP operations used in field-oriented control transforms.
Typical applications include sensorless field-oriented control (FOC) of PMSM and BLDC motors, digital power supplies and PFC stages, automotive motor and pump controllers, industrial servo drives, and solar micro-inverters. The 70 MIPS core combined with 1 ns PWM resolution allows current-loop bandwidths above 10 kHz with adequate computational headroom for both Clarke-Park transforms and space-vector modulation.
When designing with this device, note that the 100-pin TQFP (12x12 mm) footprint is shared across the dsPIC33EP512GM710 family, so firmware and layout can be reused across memory and temperature variants. Decouple each VDD pin with a 0.1 uF ceramic capacitor placed within 5 mm of the pin. Place the analog AVdd pins away from switching PWM traces to minimize coupling.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for selection, replacement, and layout decisions.
Alternatives de remplacement direct pour DSPIC33EP512GM710-I/PT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec DSPIC33EP512GM710-I/PT (même facteur de forme et même empreinte) — différant par Package, Operating Temperature, Core Architecture, Qualification, RAM.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
DSPIC33EP512GM710-E/PT
✅ Remplacement direct✓ En stock
$6.55 / unité
Voir la fiche technique →DSPIC33EP512GM710-H/PT
✅ Remplacement direct✓ En stock
$6.3 / unité
Voir la fiche technique →DSPIC33EP512GM710T-I/PT
✅ Remplacement direct✓ En stock
$13.85 / unité
Voir la fiche technique →DSPIC33EP512GM710-E/PTVAO
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DSPIC33EP512GM710T-E/PTVAO
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DSPIC33EP512MC806-E/PT
✅ Remplacement direct✓ En stock
$8.75 / unité
Voir la fiche technique →DSPIC33EP512GM710-I/PT Valeurs maximales et caractéristiques électriques
| Core Processor | dsPIC |
| Core Size | 16-bit |
| Series | dsPIC33EP |
| Speed (MIPS) | 70 MIPS at 70 MHz |
| Program Memory (Flash) | 512 KB (170K x 24-bit) |
| RAM | 48 KB |
| Operating Voltage (VDD) | 3.0 V to 3.6 V |
| Température de fonctionnement | -40 C to +85 C (Industrial) |
| Boîtier | 100-pin TQFP (12x12 mm) |
| Type de montage | Surface Mount |
| Motor-Control PWM Channels | 12 outputs, 1 ns resolution |
| On-Chip Operational Amplifiers | 4 |
| Input Capture / Output Compare | 8 / 8 |
| Quadrature Encoder Interfaces (QEI) | 2 |
| DMA Channels | 4 |
| CAN Modules | 2 (ECAN) |
| Connectivity | CAN, I2C, IrDA, LIN, QEI, SPI, UART/USART |
| Boundary Scan (JTAG) | Yes |
| Process Technology | CMOS |
| Niveau MSL | 3 (168 hours) |
| Statut RoHS | Compliant |
Guide de configuration des broches du DSPIC33EP512GM710-I/PT 100-pin tqfp (12x12 mm)
Configuration des broches du DSPIC33EP512GM710-I/PT (boîtier 100-pin tqfp (12x12 mm)). Ce circuit intégré numérique comprend des GPIO, des interfaces de communication (UART, SPI, I2C) et des broches d'alimentation. Consultez la fiche technique du fabricant pour les fonctions alternatives des broches et les options de configuration. Indispensable pour la conception de systèmes embarqués et la conception de circuits imprimés.
Aucune donnée de brochage détaillée disponible pour DSPIC33EP512GM710-I/PT.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
DSPIC33EP512GM710-I/PT convient pour 6 applications: PMSM / BLDC Field-Oriented Control, Digital Power Supplies and PFC, Automotive Motor and Pump Control, Industrial Servo Drives, Solar Micro-Inverters and String Inverters, Industrial Automation Controllers.
PMSM / BLDC Field-Oriented Control
The DSPIC33EP512GM710-I/PT is purpose-built for sensorless and sensored FOC of permanent-magnet synchronous motors and brushless DC motors. Its 70 MIPS dsPIC core with hardware MAC and barrel shifter executes Clarke-Park transforms and space-vector PWM inside 1 us, leaving headroom for application-layer comms. The 12 PWM channels with 1 ns edge resolution provide 16-bit duty accuracy at 20 kHz switching frequency, while the four integrated op amps enable dual-shunt current sensing without external signal-conditioning stages. Together these peripherals allow current-loop bandwidths above 10 kHz for high-dynamic servo and traction applications.
Recommandé
Digital Power Supplies and PFC
In digitally controlled switch-mode power supplies and power-factor-correction stages, the DSPIC33EP512GM710-I/PT delivers 70 MIPS and 12 PWM channels with 1 ns resolution for interleaved PFC and LLC topologies. The on-chip 12-bit ADC samples within 750 ns, allowing average-current-mode control at switching frequencies up to 2 MHz. Four DMA channels move ADC samples to memory without CPU overhead, enabling cycle-by-cycle regulation. The dual CAN modules and UART peripherals support PMBus, UART-based house-keeping comms, and parallel-module synchronization in modular power converters.
Recommandé
Automotive Motor and Pump Control
Automotive electric water pumps, oil pumps, and HVAC blowers leverage the DSPIC33EP512GM710-I/PT for integrated FOC control over a LIN or CAN interface. Its 100-pin TQFP package supports the full motor-control peripheral set on a single chip, eliminating the need for an external op-amp IC and reducing BOM cost. The industrial temperature grade (-40 C to +85 C) covers under-hood environments, while the AEC-Q100 -VAO catalog variants extend this to automotive-qualified deployments. Dual CAN modules allow gateway communication between the inverter node and the vehicle CAN-FD bus.
Recommandé
Industrial Servo Drives
Precision industrial servo drives use the DSPIC33EP512GM710-I/PT to execute cascaded position-velocity-current control loops at sub-millisecond update rates. The dual QEI interfaces accept A/B/Index signals from two encoders (motor + load) simultaneously, while 8 input-capture channels timestamp feedback pulses. Four on-chip op amps condition current-shunt signals at 50 A peak per phase for sub-1 kW servo axes. JTAG boundary scan and 4 DMA channels reduce CPU overhead in data-movement-intensive loops, leaving the dsPIC core free for the inverse dynamics computation in real time.
Recommandé
Solar Micro-Inverters and String Inverters
In photovoltaic micro-inverters, the DSPIC33EP512GM710-I/PT drives MPPT, interleaved PFC, and full-bridge inversion in a single chip. Its 70 MIPS sustains perturb-and-observe MPPT at 50 Hz update rates while running SVPWM and grid-synchronization PLLs at the same time. The four DMA channels offload ADC sample transfer, freeing CPU cycles for inverter-grid islanding detection. The dual ECAN modules communicate with a centralized panel-level energy-management controller, while IrDA/UART support wireless commissioning in the field.
Recommandé
Industrial Automation Controllers
General-purpose industrial automation controllers leverage the DSPIC33EP512GM710-I/PT for stepper motor control, brushed DC drives, and multi-axis coordination. Its 8/8 input-capture/output-compare channels handle multiple encoder inputs and PWM outputs simultaneously, while 4 DMA channels and JTAG boundary scan simplify firmware bring-up. Dual CAN buses plus UART and SPI allow modular I/O expansion over industrial fieldbus networks. The 48 KB RAM supports real-time motion profiles in addition to the control loop, enabling standalone multi-axis motion sequencing.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DSPIC33EP512GM710-I/PT — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DSPIC33EP512GM710-E/PT | DSPIC33EP512GM710-H/PT | DSPIC33EP512GM710T-I/PT | DSPIC33EP512GM710-E/PTVAO | DSPIC33EP512MC806-E/PT |
|---|---|---|---|---|---|---|
| Package | 100-pin TQFP (12x12 mm) | 100-pin TQFP (12x12 mm) - same | 100-pin TQFP (12x12 mm) - same | 100-pin TQFP (12x12 mm) - same | 100-pin TQFP (12x12 mm) - same | 100-pin TQFP (12x12 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Speed | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS | 60 MIPS (VAO spec) | 70 MIPS |
| Flash / RAM | 512 KB / 48 KB | 512 KB / 48 KB | 512 KB / 48 KB | 512 KB / 48 KB | 512 KB / 48 KB | 512 KB / 48 KB |
| Operating Temperature | -40 C to +85 C (I grade) | -40 C to +125 C | -40 C to +150 C Tj | -40 C to +85 C | -40 C to +125 C | -40 C to +125 C |
| On-Chip Op Amps | 4 | 4 | 4 | 4 | 4 | 0 |
| PWM Channels | 12 | 12 | 12 | 12 | 12 | 12 |
| CAN Modules | 2 (ECAN) | 2 (ECAN) | 2 (ECAN) | 2 (ECAN) | 2 (ECAN) | 2 (ECAN) |
Principaux différenciateurs
- Four on-chip operational amplifiers eliminate external current-sense signal conditioning (vs DSPIC33EP512MC806-E/PT)
- Industrial -40 C to +85 C temperature range matches the most common deployment envelope (vs DSPIC33EP512GM710-E/PT)
- Hardware DSP MAC and barrel shifter accelerate motor-control transforms (vs ATSAM3U4EA-CU (Cortex-M3 MCU))
Notes de conception
Decouple each VDD pin with a 0.1 uF ceramic capacitor placed within 5 mm of the pin. Add a bulk 10 uF tantalum or ceramic capacitor near the IC. Place analog AVdd pins away from switching PWM traces, and route the analog ground (AVss) separately back to a star ground under the IC before joining the digital ground plane.
Estimated: at 70 MIPS and 3.3 V, the DSPIC33EP512GM710-I/PT draws approximately 70 mA active core current, dissipating ~230 mW. In the 100-pin TQFP package with theta_JA around 50 C/W, junction temperature rise is roughly 11.5 C above ambient. Ensure the layout uses a continuous ground pad below the IC for heat spreading; no external heatsink is required for typical motor-control applications.
Do not exceed 3.6 V on any VDD or AVdd pin - latch-up risk. Avoid routing high-current PWM outputs directly adjacent to the analog ADC inputs; use ground shielding or guard traces. The on-chip op amps have limited input common-mode range (typically AVss to AVdd); bias shunts correctly to avoid saturation. Configure unused PWM pins as GPIO outputs low to minimize EMI.
The 1 ns PWM resolution requires the switching node to be free of ringing within 10 ns of the edge. Use gate-driver ICs with sub-25 ns propagation delay matching, and keep the gate-driver-to-MOSFET loop under 1 nH by minimizing physical loop area. Place RC snubbers on each switching node sized to damp the parasitic ringing between 50-100 MHz.
Informations de conformité
RoHS compliant per Microchip product page. Not AEC-Q100 qualified - select DSPIC33EP512GM710-E/PTVAO for automotive. Halogen-free status not explicitly stated in the verified data.
