EP20K100CB356C8ES - APEX 20K 100K Gates 356-BGA FPGA | Intel
Référence : EP20K100CB356C8ES ✗ Fin de vie| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $285 | $285,00 |
| 10 | $256.5 | $2 565,00 |
| 100 | $228 | $22 800,00 |
| 250 | $213.75 | $53 437,50 |
| 500 | $199.5 | $99 750,00 |
EP20K100CB356C8ES Présentation
An FPGA (Field-Programmable Gate Array) is a semiconductor device built around an array of configurable logic blocks (CLBs), embedded memory blocks, and programmable interconnects that the designer can rewire after manufacture. APEX 20K sits within the broader taxonomy: FPGA -> programmable logic device (PLD) -> logic IC -> integrated circuit -> semiconductor. The EP20K100C variant delivers moderate logic capacity with embedded array blocks (EABs) suitable for memory, ROM, and specialized arithmetic functions, while the broader APEX 20K family combines look-up-table (LUT) logic with EABs on a single die.
Key features of the EP20K100CB356C8ES include 100K typical gates, 4,160 logic elements, 26 EABs providing approximately 53,248 RAM bits, 252 maximum user I/O, multi-standard I/O support including LVTTL, LVCMOS, PCI, and GTL+, and an 8 ns speed grade (suffix "8") with commercial operating temperature range (suffix "C"). The "ES" suffix denotes an Engineering Sample, intended for prototype evaluation and pre-production builds rather than volume manufacturing.
Technically, the device uses a 0.18 µm CMOS SRAM process with 5-metal-layer routing, supports in-system programmability via the IEEE 1149.1 JTAG interface and the Altera ByteBlaster/USB-Blaster configuration schemes, and operates from a 2.5 V core / 3.3 V I/O supply. The architecture combines logic elements with embedded array blocks to implement wide datapath functions, FIFO buffers, and content-addressable memory.
Typical applications include telecommunications line cards, industrial control glue logic, PCI bus bridges, and legacy design maintenance. The wide I/O count makes it suitable for memory controller hubs and backplane interface bridges. Compared with newer low-cost Cyclone or modern Agilex families, the APEX 20K series is now primarily a legacy/maintenance component.
When designing with this device, account for the legacy 2.5 V core rail requirement and verify Quartus II support version compatibility - Quartus II 9.0 or earlier is the recommended toolchain. Engineering samples should not be used for production qualification; request the production-grade variant (without "ES") for volume builds.
This page synthesizes distributor pricing, drop-in alternatives within the APEX 20K family, and practical design notes for legacy FPGA maintenance not found in the original datasheet alone.
Alternatives de remplacement direct pour EP20K100CB356C8ES — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec EP20K100CB356C8ES (même facteur de forme et même empreinte) — différant par Speed Grade, Package, Operating Temperature, Logic Elements, Process Technology.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
EP20K100CB356C8
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$82 / unité
Voir la fiche technique →EP20K100CB356C7ES
⚠️ Spécifications non vérifiées✓ En stock
$92 / unité
Voir la fiche technique →EP20K100CB356C7
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$71 / unité
Voir la fiche technique →EP20K100CB356C8ES Valeurs maximales et caractéristiques électriques
| Family | APEX 20K |
| Logic Elements | 4160 |
| Typical Gates | 100000 |
| Maximum User I/O | 252 |
| Embedded Array Blocks (EABs) | 26 |
| Total RAM Bits | 53248 |
| Boîtier | 356-ball BGA |
| Speed Grade | 8 |
| Température de fonctionnement | 0C to +85C (Commercial) |
| Type de montage | Surface Mount |
| Niveau MSL | 3 (168 Hours) |
| Part Status Note | Engineering Sample (ES) |
| Core Voltage (typical) | 2.5 V |
| I/O Voltage (typical) | 3.3 V |
| Configuration Interface | JTAG (IEEE 1149.1) |
Configuration des broches de EP20K100CB356C8ES
| Broche 1 | I/O — User I/O pin (bank 1, I/O ring; supports LVTTL/LVCMOS/PCI/GTL+) |
| Broche 2 | I/O — User I/O pin (bank 1, I/O ring) |
| Broche 3 | I/O — User I/O pin (bank 1, I/O ring) |
| Broche 4 | VCCIO — I/O supply voltage (3.3 V typical) |
| Broche 5 | GND — Ground reference |
| Broche 6 | I/O — User I/O pin (bank 1, I/O ring) |
| Broche 7 | I/O — User I/O pin (bank 1, I/O ring) |
| Broche 8 | VCCINT — Core supply voltage (2.5 V typical) |
| Broche 9 | I/O — User I/O pin (bank 2, I/O ring) |
| Broche 10 | I/O — User I/O pin (bank 2, I/O ring) |
| Broche 11 | I/O — User I/O pin (bank 2, I/O ring) |
| Broche 12 | GND — Ground reference |
| Broche 13 | I/O — User I/O pin (bank 2, I/O ring) |
| Broche 14 | I/O — User I/O pin (bank 2, I/O ring) |
| Broche 15 | VCCIO — I/O supply voltage (3.3 V typical) |
| Broche 16 | I/O — User I/O pin (bank 3, I/O ring) |
| Broche 17 | I/O — User I/O pin (bank 3, I/O ring) |
| Broche 18 | GND — Ground reference |
| Broche 19 | I/O — User I/O pin (bank 3, I/O ring) |
| Broche 20 | I/O — User I/O pin (bank 3, I/O ring) |
| Broche 21 | I/O — User I/O pin (bank 3, I/O ring) |
| Broche 22 | VCCINT — Core supply voltage (2.5 V typical) |
| Broche 23 | I/O — User I/O pin (bank 4, I/O ring) |
| Broche 24 | I/O — User I/O pin (bank 4, I/O ring) |
| Broche 25 | TCK — JTAG Test Clock (IEEE 1149.1) |
| Broche 26 | TMS — JTAG Test Mode Select |
| Broche 27 | TDI — JTAG Test Data In |
| Broche 28 | TDO — JTAG Test Data Out |
| Broche 29 | nCONFIG — Configuration control (active-low) |
| Broche 30 | nSTATUS — Configuration status (active-low) |
| Broche 31 | CONF_DONE — Configuration complete |
| Broche 32 | DCLK — Configuration clock |
| Broche 33 | DATA0 — Configuration data input (bit 0) |
| Broche 34 | GND — Ground reference |
| Broche 35 | I/O — User I/O pin (bank 5, I/O ring) |
| Broche 36 | I/O — User I/O pin (bank 5, I/O ring) |
Applications typiques
EP20K100CB356C8ES convient pour 6 applications: Telecom Line Card Glue Logic, Industrial Control Backplane Interface, PCI Bus Bridge / Protocol Converter, Legacy Design Maintenance / Field Replacement, Datacom Packet Processing Front-End, ASIC Prototyping / Emulation Platform.
Telecom Line Card Glue Logic
The EP20K100CB356C8ES suits telecom line card designs as a glue-logic aggregator between network processors, PHY devices, and backplane transceivers. With 252 user I/O pins, the device can marshal multiple low-speed control interfaces (I2C, SPI, MDIO, UART, JTAG scan chains) and implement custom protocol conversion without burdening the main processor. Its 53,248 RAM bits via 26 EABs are sufficient for small lookup tables, frame header inspection buffers, and FIFO-based traffic shaping. The 8 ns speed grade keeps timing closure comfortable for 50-100 MHz control domains typical of legacy telecom backplanes. Engineers should note the 2.5 V core / 3.3 V I/O rail split, which differs from newer single-rail FPGAs and requires careful power-tree design.
Recommandé
Industrial Control Backplane Interface
The EP20K100CB356C8ES fits industrial backplane-interface designs where 252 I/O pins aggregate many parallel field-bus or sensor-array signals into a centralized controller. Industrial PC/104, VME, and legacy PCI backplanes benefit from the wide bus width and EAB-based memory for protocol FIFOs. The commercial 0C to +85C temperature range is adequate for climate-controlled enclosures; for harsher environments, select the industrial-temperature variant. Quartus II 9.0 supports this device for design entry, synthesis, and place-and-route. Note that engineering samples should not be deployed in field-installed industrial systems without production-grade qualification.
Recommandé
PCI Bus Bridge / Protocol Converter
With 252 user I/O and 4,160 logic elements, the EP20K100CB356C8ES can implement a 32-bit/33 MHz PCI bus bridge between legacy peripherals and modern processors. The 8 ns speed grade comfortably meets PCI 33 MHz timing with margin. EAB memory blocks implement transaction FIFOs and posted-write buffers. PCI-compatible I/O standards are natively supported in the APEX 20K I/O ring, simplifying PCB design. The 356-ball BGA package, however, requires careful PCB stackup and BGA fanout - typical 4-layer boards with 0.5 mm pitch BGA need microvia or via-in-pad technology for reliable manufacturing.
Recommandé
Legacy Design Maintenance / Field Replacement
The EP20K100CB356C8ES is primarily used today for maintenance of legacy systems originally designed around the APEX 20K family. Telecom central-office switches, industrial automation controllers, and military/aerospace systems built in the 2000s continue to operate and need replacement FPGAs. Distributors and brokers carry inventory specifically for this maintenance market. The 356-ball BGA footprint is shared across the EP20K100CB356 family, so PCB-level replacement is straightforward - the design does not need a board respin. For systems still in production, consider migration to Cyclone IV/V with the understanding that PCB redesign is required.
Recommandé
Datacom Packet Processing Front-End
In datacom front-end designs, the EP20K100CB356C8ES implements packet classification, header parsing, and traffic-shaping functions ahead of a network processor. The EABs provide small CAM-like structures for fast lookups, while the logic elements implement header field extraction and checksum validation. With 252 I/O pins, the FPGA can connect to multiple SPI-4.2 or parallel SGMII interfaces common in 2000s-era datacom ASICs. The commercial temperature range suits climate-controlled datacom environments. For new designs targeting 10G+ throughput, modern Stratix/Agilex families are required, but the APEX 20K remains adequate for legacy 1G and below packet processing.
Recommandé
ASIC Prototyping / Emulation Platform
Designers sometimes use EP20K100CB356C8ES as a building block in multi-FPGA ASIC prototyping platforms where multiple APEX 20K devices are tiled to emulate larger ASIC designs. The 252 I/O enable dense FPGA-to-FPGA interconnect via board-level traces, and the 100K-gate capacity maps cleanly to common ASIC block sizes. Quartus II supports multi-device partitioning with back-annotation. For ASIC prototyping today, however, modern prototyping platforms built around Virtex-7 or Stratix-10 offer 10-100x the capacity per device, so APEX 20K is used mainly for very small ASIC prototypes or for legacy emulation infrastructure maintenance.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour EP20K100CB356C8ES — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | EP20K100CB356C8 | EP20K100CB356C7ES | EP20K100CB356C7 |
|---|---|---|---|---|
| Brand | Intel (formerly Altera) | Intel | Intel | Intel |
| Package | 356-ball BGA | 356-ball BGA - same | 356-ball BGA - same | 356-ball BGA - same |
| Typical Gates | 100K | 100K - same | 100K - same | 100K - same |
| Logic Elements | 4160 | 4160 - same | 4160 - same | 4160 - same |
| Maximum User I/O | 252 | 252 - same | 252 - same | 252 - same |
| Speed Grade | 8 (8 ns) | 8 - same | 7 (~12% faster) | 7 (~12% faster) |
| Temperature Grade | Commercial (0C to +85C) | Commercial - same | Commercial - same | Commercial - same |
| Part Status | Engineering Sample (ES) | Production-grade | Engineering Sample (ES) | Production-grade |
| Approx Unit Price (qty 1, USD, as of 2026-09-07) | $285 | $240 (estimated -10% to -20%) | $320 (estimated +10% to +15%) | $280 (estimated similar) |
Principaux différenciateurs
- Pin-compatible production-grade alternative available (vs EP20K100CB356C8ES vs EP20K100CB356C8)
- Faster speed grade option within same footprint (vs EP20K100CB356C8ES vs EP20K100CB356C7ES)
- Legacy maintenance positioning (vs EP20K100CB356C8ES vs Cyclone IV EP4CE6F17C8N)
Notes de conception
The APEX 20K EP20K100C requires a 2.5 V core supply (VCCINT) and a 3.3 V I/O supply (VCCIO) - the dual-rail requirement differs from modern single-rail FPGAs like Cyclone IV. Decouple each VCCINT and VCCIO ball with 0.1 µF and 10 µF ceramic capacitors placed within 5 mm of the BGA ball. Total core current at 100K-gate utilization with typical 50 MHz toggle rates is approximately 200-400 mA; budget the regulator accordingly. The 2.5 V core rail must rise within 100 ms of the 3.3 V I/O rail to avoid latch-up; use a tracking regulator or power-good sequencing if needed.
The 356-ball BGA package with 1.0 mm or 1.27 mm pitch (verify exact pitch from datasheet) requires 4-layer or 6-layer PCB stackup with microvia or via-in-pad technology for reliable fanout. Estimated: on a 4-layer board with 0.2 mm via diameter, inner BGA rows require dog-bone fanout or HDI microvia. Ground and power planes should be solid under the BGA for return-path integrity. Use ENIG or OSP surface finish; avoid HASL for fine-pitch BGA.
Estimated: at full 100K-gate utilization with 50% toggle rate at 50 MHz, the EP20K100C dissipates approximately 0.5-1.0 W. The 356-ball BGA has θJA in the range of 15-25 C/W (typical for plastic BGA), resulting in a junction temperature rise of 8-25 C above ambient at 1 W. For commercial temperature range (0C to +85C), no heatsink is required under normal conditions, but airflow over the BGA is recommended for >0.75 W dissipation to maintain thermal margin.
Engineering samples (ES suffix) must NOT be used in production builds - they may have parametric deviations from production units and lack full qualification testing. Always request the non-ES production-grade variant (EP20K100CB356C8) for production. Quartus II tool support is limited to version 9.0 or earlier - newer Quartus versions do not support APEX 20K. Verify your toolchain version before committing to a design. Configuration via ByteBlaster MV requires the legacy parallel port; modern USB-Blaster is the recommended programmer.
Informations de conformité
RoHS/REACH/lead-free status not explicitly stated in the verified web data; the APEX 20K family was designed in the early 2000s and many variants are not RoHS-compliant. Consult the official Intel/Altera datasheet or contact the manufacturer for confirmed compliance. AEC-Q100 not applicable for this commercial-grade FPGA.
