Texas Instruments

INA125TDA1 - Precision Instrumentation Amplifier Die | TI

Référence : INA125TDA1 ✓ Actif
10,000 V/V Vdss 0.025 uA Id Rectangular die Package
MOQ : 1 |

INA125TDA1 Présentation

The Texas Instruments INA125TDA1 is a single-circuit instrumentation amplifier with an integrated precision voltage reference, a maximum voltage gain of 10,000, a minimum common-mode rejection ratio of 107 dB, and a nominal bandwidth of 0.15 MHz, supplied in rectangular die form with 17 terminals. It is designed for precision differential-signal conditioning where high common-mode rejection, adjustable gain, and a low-noise reference are important.

An instrumentation amplifier is a specialized analog amplifier that measures the voltage difference between two inputs while rejecting signals common to both inputs. Within the amplifier hierarchy, an instrumentation amplifier is a differential amplifier optimized for high input impedance, accurate gain control, and excellent common-mode rejection. This makes it more useful than a general-purpose operational amplifier for sensor outputs, bridge circuits, and other systems where large common-mode voltages may coexist with a small differential signal.

The INA125TDA1 provides a gain of up to 10,000, a minimum CMRR of 107 dB, and a nominal bandwidth of 0.15 MHz. Its integrated precision voltage reference can support bridge excitation and other measurement systems that require an internal reference. The listed maximum input bias current of 0.025 uA is also useful in high-impedance sensor applications because it minimizes disturbance of the source being measured.

Internally, the device combines instrumentation-amplifier signal conditioning with a precision reference in one circuit. The broad gain range supports applications ranging from moderate-level sensor signals to millivolt-level inputs. Because gain and bandwidth trade against one another in practical signal chains, the usable bandwidth generally decreases at higher gains, so the selected gain must be checked against the required measurement bandwidth and settling behavior.

Typical uses include load-cell and strain-gauge front ends, precision bridge measurement, low-level differential sensing, industrial instrumentation, and laboratory signal conditioning. The die format is particularly relevant to manufacturers that require bare-die assembly, wafer-level integration, or customized packaging rather than a standard leaded or surface-mount package.

Design work should begin with the manufacturer's INA125 pin-description table and electrical-characteristics table because the exposed die requires assembly-specific bonding and the exact terminal assignments are critical. Designers should also verify gain-set resistor values, reference loading, supply headroom, output swing, input common-mode limits, and the bandwidth required at the selected gain before releasing a production design.

This page combines the die-level device information, verified pricing record, functional family comparisons, and application-specific engineering guidance to support sourcing and design decisions. It distinguishes the bare-die INA125TDA1 from packaged INA125 devices and emphasizes why package, pinout, qualification, and thermal requirements must be verified during replacement planning.

Alternatives de remplacement direct pour INA125TDA1 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Aucune alternative de remplacement direct disponible pour ce produit.

Demander des alternatives

INA125TDA1 Valeurs maximales et caractéristiques électriques

Device Type Single-circuit instrumentation amplifier with precision voltage reference
Number of Circuits 1 circuit
Maximum Voltage Gain 10,000 V/V
Minimum Common-Mode Rejection Ratio 107 dB
Nominal Bandwidth 0.15 MHz
Maximum Average Bias Current 0.025 uA
Package Type Rectangular die
Number of Terminals 17 terminals
Die Width 1.9558 mm
Mounting Form No-lead die assembly
Reference Integrated precision voltage reference
Input Type Differential input
Common-Mode Rejection 107 dB minimum

Guide de configuration des broches du INA125TDA1 rectangular die

Configuration des broches du INA125TDA1 (boîtier rectangular die). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.

Schéma de brochage du boîtier rectangular die pour le INA125TDA1

Aucune donnée de brochage détaillée disponible pour INA125TDA1.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

INA125TDA1 convient pour 6 applications: Load-Cell Front End, Precision Bridge Measurement, Low-Level Differential Sensing, Industrial Instrumentation, Laboratory Signal Conditioning, Custom Semiconductor Integration.

⚖️

Load-Cell Front End

The INA125TDA1 fits load-cell and strain-gauge measurements that produce small differential signals in the presence of a much larger common-mode bridge excitation. Its maximum voltage gain of 10,000 supports high-gain signal extraction, while the 107 dB minimum common-mode rejection ratio helps prevent excitation voltage from dominating the measurement. The integrated precision voltage reference can support bridge-oriented designs. During implementation, verify the actual bridge excitation scheme, gain-set resistor network, input common-mode limits, output swing, and the 0.15 MHz nominal bandwidth at the intended gain.

🏭

Precision Bridge Measurement

INA125TDA1 is appropriate for precision bridge excitation and readout circuits where excitation accuracy, common-mode rejection, and differential gain determine measurement quality. A maximum gain of 10,000 can increase millivolt-level bridge imbalance to a more useful output range, while the integrated precision voltage reference provides a local reference option. The design must account for gain-dependent bandwidth, reference stability, bridge impedance, resistor tolerance, and input bias current. A custom die assembly also requires a controlled pad map, orientation procedure, and electrical test plan.

🧩

Low-Level Differential Sensing

The INA125TDA1 can condition low-level differential outputs from sensors when the design benefits from high common-mode rejection rather than a conventional single-ended amplifier stage. Its 0.025 uA maximum average bias current is favorable for high-impedance sources, while the 107 dB minimum CMRR helps reject shared noise or voltage on both inputs. Engineers should verify whether the sensor output is truly differential, confirm the usable bandwidth at the selected gain, and keep routing symmetrical to minimize conversion of common-mode disturbance into differential error.

🏭

Industrial Instrumentation

INA125TDA1 supports custom industrial instrumentation that must amplify differential sensor signals under varying common-mode conditions. The high maximum gain of 10,000 and 107 dB minimum CMRR provide useful headroom for low-amplitude process measurements, while the precision reference supports systems requiring a controlled internal reference. For factory equipment, the die should be integrated into a qualified assembly with stable thermal behavior, protected routing, clean grounding, and appropriate calibration. Validate the complete channel against environmental noise, electrical isolation requirements, and long-term offset and drift performance.

🖥️

Laboratory Signal Conditioning

INA125TDA1 can serve as the analog front end of a laboratory measurement instrument when small differential signals require adjustable gain and strong common-mode rejection. Its maximum gain of 10,000 accommodates sensitive sensor and bridge inputs, and the integrated precision voltage reference may simplify reference architecture for specialized equipment. Instrument designers should account for the nominal 0.15 MHz bandwidth, gain-bandwidth behavior, settling requirements, input capacitance, and output-drive limitations. Bare-die assembly also makes thermal characterization and post-assembly calibration especially relevant to instrument-level accuracy.

🔧

Custom Semiconductor Integration

The rectangular 17-terminal die format makes INA125TDA1 suitable for manufacturers integrating the INA125 directly into a custom module, wafer-level assembly, or application-specific semiconductor package. The 1.9558 mm listed die width provides a physical constraint for bonding and layout planning, while the single-circuit instrumentation amplifier and precision reference support a compact analog front end. Integration engineering must define pad assignment, die orientation, clean handling, wire-bond or flip-chip parameters, heat dissipation, continuity tests, and final calibration. The finished assembly should be validated against the electrical performance of the packaged INA125 family.

What is the INA125TDA1?
The INA125TDA1 is a single-circuit Texas Instruments instrumentation amplifier with an integrated precision voltage reference, supplied as a rectangular no-lead die. According to the Texas Instruments INA125 product page and manufacturer datasheet, the device supports a maximum voltage gain of 10,000, a minimum common-mode rejection ratio of 107 dB, and a nominal bandwidth of 0.15 MHz. It is intended for precision differential-signal conditioning in industrial, laboratory, bridge-measurement, and custom semiconductor-assembly applications.
What are the key specifications of INA125TDA1 that engineers should know?
The principal INA125TDA1 specifications are a 10,000 maximum voltage gain, 107 dB minimum common-mode rejection ratio, 0.15 MHz nominal bandwidth, and 0.025 uA maximum average bias current. Texas Instruments identifies the device as a single-circuit instrumentation amplifier with a precision voltage reference and packages this ordering option as a 17-terminal rectangular die. The die width is listed as 1.9558 mm, so bonding, pad assignment, and assembly layout require careful review before use.
Where can I download the INA125TDA1 datasheet PDF?
The INA125TDA1 datasheet should be obtained from the Texas Instruments INA125 product page or the manufacturer PDF linked by that page. The official product page is https://www.ti.com/product/INA125 and provides ordering information, quality data, and supporting documents for the INA125 family. Use the die-specific pin-description and ordering information when assigning the 17 terminals; third-party PDF mirrors can help locate a document but should not replace the manufacturer source for production design.
Where is the INA125TDA1 pinout located?
The INA125TDA1 pinout is documented through the terminal-assignment information associated with the Texas Instruments INA125 datasheet and its die-ordering documentation. The device has 17 terminals in a rectangular die configuration rather than a standard leaded package. Do not assign connections by analogy with packaged INA125 variants: use the manufacturer's terminal table to map supply, reference, gain-setting, input, output, and exposed or mechanical terminals before creating a bond map or fixture.
Is the INA125TDA1 suitable for load-cell and strain-gauge measurements?
The INA125TDA1 is suitable for load-cell and strain-gauge front ends when the required gain, bandwidth, common-mode range, and reference behavior match the measurement system. Its maximum gain of 10,000 can accommodate small differential bridge outputs, while its 107 dB minimum CMRR helps reject large common-mode excitation voltages. The integrated precision voltage reference is valuable for bridge excitation, but the actual excitation scheme, resistor tolerances, output range, and bandwidth must be verified against the manufacturer datasheet.
What is the difference between INA125TDA1 and INA128?
INA125TDA1 is the bare-die form of the INA125 family, whereas INA128 is a separate packaged precision instrumentation-amplifier product. Texas Instruments describes INA128 as offering higher precision, lower noise, and strong capacitive-load drive capability, while INA125TDA1 combines an instrumentation amplifier with a precision voltage reference. These differences make INA128 relevant for signal-chain performance comparisons, but not a die-to-package drop-in replacement because its package, terminal arrangement, and electrical behavior must be assessed independently.
What is the difference between INA125TDA1 and INA828?
INA125TDA1 and INA828 belong to different instrumentation-amplifier families and do not share a verified package or pin arrangement. The INA125TDA1 provides an integrated precision voltage reference and is offered here as a 17-terminal rectangular die, whereas INA828 is a distinct precision amplifier family listed by Texas Instruments in its alternate-product comparison. A board-level substitution would require complete checks of gain, bandwidth, noise, input and output ranges, reference requirements, power supply, layout, and package geometry.
When should I choose INA125TDA1 over INA128?
Choose INA125TDA1 when the design specifically needs the INA125-family combination of an instrumentation amplifier and integrated precision reference, and when bare-die assembly is acceptable or required. Consider INA128 instead when its higher-precision, lower-noise architecture and capacitive-load drive capability better match a packaged signal-chain design. The decision must include device qualification, die bonding, thermal performance, reference noise, common-mode range, stability, and the exact output bandwidth required by the measurement channel.
When should I choose INA125TDA1 over INA828?
Choose INA125TDA1 when an integrated precision voltage reference, die-level assembly, and the specific INA125 electrical characteristics are essential to the design. Choose INA828 when its separate-family performance and packaged implementation are better suited to the application. Because no pin-compatible equivalence between these products has been established, a footprint change, signal-path recalculation, stability review, and new qualification cycle should be expected rather than treating the change as a drop-in replacement.
What can replace INA125TDA1?
No verified pin-compatible drop-in replacement for INA125TDA1 has been established in the available family comparison. INA128 and INA828 are relevant functional alternatives, but neither is demonstrated as having the same rectangular 17-terminal die footprint, terminal assignments, and electrical behavior. A practical replacement search must compare die dimensions, bonding pads, pad functions, gain network, reference voltage, supply range, common-mode range, noise, bandwidth, output swing, and qualification requirements.
Is INA125TDA1 the same as INA128?
No. INA125TDA1 is a bare-die INA125-family instrumentation amplifier with an integrated precision reference, while INA128 is a distinct packaged instrumentation-amplifier family with different precision, noise, and load-drive characteristics. Their functions overlap, but equivalence requires a detailed electrical and footprint review. In particular, the 17-terminal die configuration of INA125TDA1 does not permit treating a conventional INA128 package as a direct pin-for-pin substitution.
Is INA125TDA1 the same as INA828?
No. INA125TDA1 and INA828 are different instrumentation-amplifier products with different package forms, documentation, and design characteristics. INA125TDA1 is a 17-terminal rectangular die with an integrated precision reference, while INA828 belongs to a separate packaged family. Their overlap in differential-signal conditioning does not establish interchangeability. Confirm the complete electrical limits, gain network, supply arrangement, stability, layout, and mechanical interface before approving either as the replacement for the other.
Where can I buy INA125TDA1 online?
Use the Request a Quote form on this page to request INA125TDA1 availability, current lead time, minimum order quantity, and assembly or delivery requirements. The bare-die format may require coordination with a qualified assembly process, so include the intended bonding method, die orientation, quantity, and target schedule in the request. Stock status and lead time should be confirmed at quotation time because die inventory and assembly capacity can vary with demand.
What is the lead time for INA125TDA1?
The current lead time for INA125TDA1 should be requested through the Request a Quote form on this page. The device is sold as a die rather than a conventional finished package, so the quotation should also cover any required assembly, test, inspection, or delivery coordination. Provide the annual demand, forecast horizon, desired trace quantity, and bonding process so the supplier can confirm a meaningful delivery commitment.
Is INA125TDA1 in stock?
Current INA125TDA1 stock should be confirmed through the Request a Quote form on this page. A recorded inventory reference does not replace a transaction-specific stock confirmation for a bare-die device, especially when packaging, testing, or assembly requirements are involved. Include the required quantity, target date, die-handling requirements, and shipment destination in the request to obtain the most useful availability response.
How much does INA125TDA1 cost?
Use the Request a Quote form on this page for the current INA125TDA1 price. The quote should reflect the exact die ordering option, requested quantity, assembly or testing requirements, delivery terms, and any applicable shipping or handling needs. Pricing for bare-die semiconductors can depend on order volume and procurement conditions, so a live quotation is more useful than a historical unit-price record for production planning.
What design checks are required for an INA125TDA1 die assembly?
An INA125TDA1 die assembly should be reviewed for pad mapping, die orientation, bond-wire or flip-chip constraints, thermal paths, cleanliness, and electrical performance after packaging. The 17-terminal assignment must follow the manufacturer terminal table, and the analog layout should provide a low-impedance ground, clean supply decoupling, controlled gain resistors, and minimal differential-loop area. Because this is a bare die, assembly yield and post-packaging test must be included in the product verification plan.

Données de référence d'ingénierie pour INA125TDA1 — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose INA125TDA1 when the design specifically requires an INA125-family instrumentation amplifier, an integrated precision voltage reference, and bare-die assembly. Its maximum gain of 10,000, 107 dB minimum CMRR, and 0.025 uA maximum average bias current make it relevant for bridge, strain-gauge, and low-level differential measurement systems. Choose INA128 when a packaged, higher-precision, lower-noise amplifier with stronger capacitive-load drive is more important than die integration and the INA125 reference architecture. Choose INA828 only after checking its separate family requirements against the full signal chain. Neither functional alternative is established as a pin-compatible replacement for the 17-terminal die, so any substitution should be treated as a redesign with new package, layout, stability, thermal, and qualification work.

Comparaison avec les alternatives

Paramètre Ce produit
Package Rectangular 17-terminal die
Brand Texas Instruments
Circuit Count 1 circuit
Maximum Voltage Gain 10,000 V/V
Minimum Common-Mode Rejection Ratio 107 dB
Nominal Bandwidth 0.15 MHz
Maximum Average Bias Current 0.025 uA
Integrated Reference Precision voltage reference

Principaux différenciateurs

  • Bare-die integration format (vs INA128)
  • Integrated precision voltage reference (vs INA828)
  • High common-mode rejection (vs INA128)

Notes de conception

Use the manufacturer terminal-description table to create the bonding map before layout work begins. Maintain symmetrical routing between the differential inputs, place gain-setting components close to their specified terminals, and provide a low-impedance return for every supply and reference connection. Because the device is supplied as a die, document die orientation, pad numbering, bond sequence, and inspection criteria as part of the assembly drawing rather than relying on a conventional package land pattern.

Treat the input network, reference connection, and output path as high-impedance precision analog routes. Keep copper and switching nodes away from the die pads, use short differential connections, and return analog current through a quiet ground structure. The 0.15 MHz nominal bandwidth should be treated as a starting characteristic rather than a guaranteed bandwidth at every gain; verify gain-bandwidth behavior, settling, capacitive loading, and output drive in the manufacturer electrical-characteristics table.

Do not substitute a packaged INA125 variant or a different instrumentation-amplifier family solely by function. The die dimensions, terminal count, pad assignment, reference implementation, gain network, and package parasitics can differ materially. Before releasing a replacement, compare input common-mode range, output swing, gain error, CMRR, offset, noise, bandwidth, supply range, and reference performance, then repeat thermal and functional testing after the new assembly is built.

Develop a thermal plan around the assembled die, copper, substrate, bond wires, and enclosure rather than the die alone. The listed die width of 1.9558 mm does not establish junction temperature or allowable dissipation, and those figures cannot be inferred without the assembly geometry and operating conditions. Correlate temperature-sensitive measurements during characterization, define safe handling limits for assembly, and verify production calibration across the intended ambient range.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated for this die ordering option. Confirm the applicable quality and environmental documentation with Texas Instruments before qualification.

Données vérifiées le : 2026-11-19 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

INA125TDA1 datasheet INA125TDA1 pinout INA125TDA1 datasheet pdf INA125TDA1 die package INA125TDA1 instrumentation amplifier INA125TDA1 precision reference INA125TDA1 equivalent INA125TDA1 replacement INA125TDA1 cross reference INA125TDA1 price INA125TDA1 stock Texas Instruments INA125TDA1 INA125TDA1 load cell amplifier INA125TDA1 vs INA128 INA125TDA1 17 terminal die

Composants & termes associés

Texas Instruments INA125TDA1 INA125 INA128 INA828 instrumentation amplifier differential amplifier analog amplifier precision voltage reference common-mode rejection ratio CMRR voltage gain input bias current nominal bandwidth load-cell amplifier strain-gauge bridge industrial instrumentation laboratory signal conditioning rectangular die 17-terminal die surface-mount assembly semiconductor precision measurement low-level differential sensing
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ