ISL8325IB-T - Dual 60Ω SPST Analog Switch | Renesas Electronics
Référence : ISL8325IB-T ✓ ActifISL8325IB-T Présentation
An analog switch is a solid-state semiconductor device that connects or isolates circuit nodes using controlled voltage signals. The SPST configuration provides one normally open or normally closed conduction path, while a dual-switch package can route two independent signals. Within the broader hierarchy, this product is an analog switch IC, interface IC, and discrete-level signal-routing component used to build multiplexers, sample-and-hold paths, and configurable analog front ends.
The key operating characteristics are the dual SPST architecture, 60 Ω nominal on-resistance, 1:1 switch topology, and single-supply range of 1.8 V to 12 V. The -T ordering suffix identifies the tape-and-reel shipping configuration. These characteristics make the ISL8325IB-T appropriate for low-voltage analog signal paths where two channels must be switched without adding a mechanically complex relay.
The ISL8323 through ISL8325 family is designed for precision analog switching in single-supply systems. Renesas describes these devices for battery-powered equipment, where the combination of low-voltage operation and a compact surface-mount package helps conserve board area. Two switches in one package also reduce component count compared with two separate single-switch ICs. Because on-resistance can vary with supply voltage and signal amplitude, the application should verify the datasheet resistance curve against the actual signal range.
Typical uses include battery-powered measurement systems, portable medical or industrial instruments, analog test equipment, signal routing between a sensor and an amplifier, and multiplexed low-voltage data-acquisition systems. In a multiplexed design, separate switches can bring different sensor outputs onto a common amplifier or converter input. The switch-control signals should remain within the logic thresholds specified for the selected supply voltage.
The primary design consideration is ensuring that analog signals never exceed the device's absolute maximum ratings, particularly during power-down or when a control input remains high while the supply collapses. Place the IC close to the signals it routes, keep high-impedance nodes short, and provide a stable supply reference. The manufacturer pin description and electrical characteristics should be used when assigning PCB tracks and logic levels.
This product page combines the device architecture, verified source links, application guidance, pinout status, and engineering-oriented selection information. It also distinguishes the required SOIC footprint from unsupported alternatives, helping designers avoid substitutions that look electrically similar but cannot be mounted pin-to-pin.
Alternatives de remplacement direct pour ISL8325IB-T — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec ISL8325IB-T (même facteur de forme et même empreinte) — différant par Number of Terminals, On Resistance.
ISL8325IB
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →ISL8323IB-T
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →ISL8324IB-T
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →ISL83483IBZ-T
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL83491IBZ
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
ISL8325IB-T Valeurs maximales et caractéristiques électriques
| Number of Circuits | 2 circuits |
| Switch Configuration | Dual SPST |
| On Resistance | 60 ohm |
| Signal-to-Switch Ratio | 1:1 |
| Supply Type | Single supply |
| Minimum Supply Voltage | 1.8 V |
| Maximum Supply Voltage | 12 V |
| Boîtier | 8-pin SOIC |
| Type de montage | Surface mount |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
| Number of Terminals | 8 |
| Device Type | Analog switch IC |
Guide de configuration des broches du ISL8325IB-T rectangular
Configuration des broches du ISL8325IB-T (boîtier rectangular). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour ISL8325IB-T.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
ISL8325IB-T convient pour 6 applications: Battery-Powered Measurement Systems, Portable Industrial Sensors, Low-Voltage Data Acquisition, Analog Test Equipment, Portable Medical Instruments, Signal Routing and Multiplexing.
Battery-Powered Measurement Systems
The ISL8325IB-T fits battery-powered measurement equipment because it supports a single 1.8 V to 12 V supply and combines two independent SPST switches in one 8-pin SOIC. It can route selected sensor or conditioning signals into a shared analog front end while limiting the number of discrete switching packages. Because the control thresholds and switching transients depend on the supply voltage, configure the logic levels and signal amplitudes from the manufacturer electrical characteristics before finalizing the battery operating range.
Recommandé
Portable Industrial Sensors
The dual SPST topology of the ISL8325IB-T allows two sensor paths to be selected independently in compact industrial sensing equipment. Its 60 Ω nominal on-resistance and 1:1 topology suit low-frequency analog measurement paths, while the 8-pin SOIC package simplifies board assembly. The design should keep switched nodes away from high-impedance amplifiers during transitions and confirm that source signals remain within the device's absolute maximum limits at the lowest battery voltage.
Recommandé
Low-Voltage Data Acquisition
The ISL8325IB-T can provide two selectable analog channels in a low-voltage data-acquisition front end. Each SPST path can connect a different sensor output toward a shared amplifier or converter input, reducing routing complexity while maintaining a compact 8-pin SOIC footprint. Verify switch leakage, charge injection, and off-state behavior against the measurement accuracy and bandwidth requirements, since those numerical characteristics are application-sensitive and should be taken from the manufacturer datasheet.
Recommandé
Analog Test Equipment
The ISL8325IB-T is appropriate for switching two test signals within compact analog test equipment because the package integrates two SPST switches and supports supplies from 1.8 V to 12 V. The 60 Ω nominal on-resistance provides a defined starting point for loss budgeting, although the complete frequency-dependent resistance must be checked at the signal frequency. Place the switch close to the instrumentation node and use short, shielded routing when measuring small signals.
Recommandé
Portable Medical Instruments
The ISL8325IB-T can route two low-level analog channels in portable medical instrumentation when the interface is designed around its 1.8 V to 12 V single-supply capability. The dual SPST arrangement reduces component count, while the small SOIC package supports compact assemblies. Signal integrity and safety depend on the complete system architecture, so engineers should validate leakage, switching transients, isolation requirements, and control behavior under worst-case operating conditions.
Recommandé
Signal Routing and Multiplexing
The ISL8325IB-T is useful in simple two-channel analog multiplexing arrangements because each SPST switch independently connects or isolates a signal path. Designers can build selectable sensor inputs, switched test points, or configurable amplifier paths without using a relay. The 60 Ω nominal on-resistance must be included in the signal-path budget, and the control outputs should be driven only when the supply is stable enough to prevent unintended intermediate switch states.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour ISL8325IB-T — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | ISL8325IB | ISL8323IB-T | ISL8324IB-T | ISL83483IBZ-T | ISL83491IBZ |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-pin SOIC | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Principaux différenciateurs
- Combines two independent analog switches in one compact package (vs ISL8325IB)
- Supports low-voltage single-supply designs (vs ISL8323IB-T)
- Uses the same 8-pin SOIC footprint as the principal family alternatives (vs ISL8324IB-T)
Notes de conception
Do not treat all members of the ISL832x or ISL834xx families as automatically interchangeable. Although the alternatives listed here use the same 8-pin SOIC footprint, switch-state behavior, control polarity, logic thresholds, and detailed electrical limits can vary by family member. Compare every numbered pin and the application-relevant electrical characteristics against the manufacturer datasheet before releasing a substitution to production.
Route the switched analog signals as short, direct traces from the ISL8325IB-T to the nodes they control. Keep the common and switched nodes away from clocks, power inductors, and digital return paths. Use a continuous ground reference, place the supply bypass capacitor close to the device, and observe the manufacturer's layout guidance when the switch sits next to high-impedance amplifier inputs or precision converter references.
Budget for the 60 ohm nominal on-resistance and any frequency-dependent variation when designing dividers, sensor interfaces, or gain stages. Switching capacitance and charge injection can create transient errors on high-impedance nodes, while off-state leakage can disturb high-impedance measurements. Confirm the actual signal bandwidth, source impedance, capacitance, and required accuracy using the manufacturer switching and leakage characteristics.
Apply control signals only after the supply has stabilized. Control transitions while VCC is rising or falling can produce unintended intermediate switch states or transient current. Check the absolute maximum supply and input-voltage limits at every operating condition, and design the logic driver so its high and low levels meet the manufacturer thresholds for the selected supply voltage.
Informations de conformité
The available product descriptions identify the device as an industrial-grade analog switch but do not explicitly state its RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. Request current compliance documentation through the Request a Quote form.