ISL8325IB-T - Dual 60Ω SPST Analog Switch | Renesas Electronics
부품 번호: ISL8325IB-T ✓ 활성ISL8325IB-T 개요
An analog switch is a solid-state semiconductor device that connects or isolates circuit nodes using controlled voltage signals. The SPST configuration provides one normally open or normally closed conduction path, while a dual-switch package can route two independent signals. Within the broader hierarchy, this product is an analog switch IC, interface IC, and discrete-level signal-routing component used to build multiplexers, sample-and-hold paths, and configurable analog front ends.
The key operating characteristics are the dual SPST architecture, 60 Ω nominal on-resistance, 1:1 switch topology, and single-supply range of 1.8 V to 12 V. The -T ordering suffix identifies the tape-and-reel shipping configuration. These characteristics make the ISL8325IB-T appropriate for low-voltage analog signal paths where two channels must be switched without adding a mechanically complex relay.
The ISL8323 through ISL8325 family is designed for precision analog switching in single-supply systems. Renesas describes these devices for battery-powered equipment, where the combination of low-voltage operation and a compact surface-mount package helps conserve board area. Two switches in one package also reduce component count compared with two separate single-switch ICs. Because on-resistance can vary with supply voltage and signal amplitude, the application should verify the datasheet resistance curve against the actual signal range.
Typical uses include battery-powered measurement systems, portable medical or industrial instruments, analog test equipment, signal routing between a sensor and an amplifier, and multiplexed low-voltage data-acquisition systems. In a multiplexed design, separate switches can bring different sensor outputs onto a common amplifier or converter input. The switch-control signals should remain within the logic thresholds specified for the selected supply voltage.
The primary design consideration is ensuring that analog signals never exceed the device's absolute maximum ratings, particularly during power-down or when a control input remains high while the supply collapses. Place the IC close to the signals it routes, keep high-impedance nodes short, and provide a stable supply reference. The manufacturer pin description and electrical characteristics should be used when assigning PCB tracks and logic levels.
This product page combines the device architecture, verified source links, application guidance, pinout status, and engineering-oriented selection information. It also distinguishes the required SOIC footprint from unsupported alternatives, helping designers avoid substitutions that look electrically similar but cannot be mounted pin-to-pin.
드롭인 대체품: ISL8325IB-T — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ISL8325IB-T (동일 폼 팩터 및 풋프린트) — 차이점: Number of Terminals, On Resistance.
ISL8325IB
✅ 드롭인가격 문의
데이터시트 보기 →ISL8323IB-T
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →ISL8324IB-T
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →ISL83483IBZ-T
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ISL83491IBZ
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ISL8325IB-T 최대 정격 & 전기적 특성
| Number of Circuits | 2 circuits |
| Switch Configuration | Dual SPST |
| On Resistance | 60 ohm |
| Signal-to-Switch Ratio | 1:1 |
| Supply Type | Single supply |
| Minimum Supply Voltage | 1.8 V |
| Maximum Supply Voltage | 12 V |
| 패키지 | 8-pin SOIC |
| 실장 유형 | Surface mount |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
| Number of Terminals | 8 |
| Device Type | Analog switch IC |
ISL8325IB-T rectangular 핀 구성 가이드
ISL8325IB-T(rectangular 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: ISL8325IB-T.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ISL8325IB-T 적합 용도: 6 애플리케이션s: Battery-Powered Measurement Systems, Portable Industrial Sensors, Low-Voltage Data Acquisition, Analog Test Equipment, Portable Medical Instruments, Signal Routing and Multiplexing.
Battery-Powered Measurement Systems
The ISL8325IB-T fits battery-powered measurement equipment because it supports a single 1.8 V to 12 V supply and combines two independent SPST switches in one 8-pin SOIC. It can route selected sensor or conditioning signals into a shared analog front end while limiting the number of discrete switching packages. Because the control thresholds and switching transients depend on the supply voltage, configure the logic levels and signal amplitudes from the manufacturer electrical characteristics before finalizing the battery operating range.
추천
Portable Industrial Sensors
The dual SPST topology of the ISL8325IB-T allows two sensor paths to be selected independently in compact industrial sensing equipment. Its 60 Ω nominal on-resistance and 1:1 topology suit low-frequency analog measurement paths, while the 8-pin SOIC package simplifies board assembly. The design should keep switched nodes away from high-impedance amplifiers during transitions and confirm that source signals remain within the device's absolute maximum limits at the lowest battery voltage.
추천
Low-Voltage Data Acquisition
The ISL8325IB-T can provide two selectable analog channels in a low-voltage data-acquisition front end. Each SPST path can connect a different sensor output toward a shared amplifier or converter input, reducing routing complexity while maintaining a compact 8-pin SOIC footprint. Verify switch leakage, charge injection, and off-state behavior against the measurement accuracy and bandwidth requirements, since those numerical characteristics are application-sensitive and should be taken from the manufacturer datasheet.
추천
Analog Test Equipment
The ISL8325IB-T is appropriate for switching two test signals within compact analog test equipment because the package integrates two SPST switches and supports supplies from 1.8 V to 12 V. The 60 Ω nominal on-resistance provides a defined starting point for loss budgeting, although the complete frequency-dependent resistance must be checked at the signal frequency. Place the switch close to the instrumentation node and use short, shielded routing when measuring small signals.
추천
Portable Medical Instruments
The ISL8325IB-T can route two low-level analog channels in portable medical instrumentation when the interface is designed around its 1.8 V to 12 V single-supply capability. The dual SPST arrangement reduces component count, while the small SOIC package supports compact assemblies. Signal integrity and safety depend on the complete system architecture, so engineers should validate leakage, switching transients, isolation requirements, and control behavior under worst-case operating conditions.
추천
Signal Routing and Multiplexing
The ISL8325IB-T is useful in simple two-channel analog multiplexing arrangements because each SPST switch independently connects or isolates a signal path. Designers can build selectable sensor inputs, switched test points, or configurable amplifier paths without using a relay. The 60 Ω nominal on-resistance must be included in the signal-path budget, and the control outputs should be driven only when the supply is stable enough to prevent unintended intermediate switch states.
추천
엔지니어링 참조 데이터: ISL8325IB-T — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ISL8325IB | ISL8323IB-T | ISL8324IB-T | ISL83483IBZ-T | ISL83491IBZ |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 8-pin SOIC | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
주요 차별점
- Combines two independent analog switches in one compact package (vs ISL8325IB)
- Supports low-voltage single-supply designs (vs ISL8323IB-T)
- Uses the same 8-pin SOIC footprint as the principal family alternatives (vs ISL8324IB-T)
설계 노트
Do not treat all members of the ISL832x or ISL834xx families as automatically interchangeable. Although the alternatives listed here use the same 8-pin SOIC footprint, switch-state behavior, control polarity, logic thresholds, and detailed electrical limits can vary by family member. Compare every numbered pin and the application-relevant electrical characteristics against the manufacturer datasheet before releasing a substitution to production.
Route the switched analog signals as short, direct traces from the ISL8325IB-T to the nodes they control. Keep the common and switched nodes away from clocks, power inductors, and digital return paths. Use a continuous ground reference, place the supply bypass capacitor close to the device, and observe the manufacturer's layout guidance when the switch sits next to high-impedance amplifier inputs or precision converter references.
Budget for the 60 ohm nominal on-resistance and any frequency-dependent variation when designing dividers, sensor interfaces, or gain stages. Switching capacitance and charge injection can create transient errors on high-impedance nodes, while off-state leakage can disturb high-impedance measurements. Confirm the actual signal bandwidth, source impedance, capacitance, and required accuracy using the manufacturer switching and leakage characteristics.
Apply control signals only after the supply has stabilized. Control transitions while VCC is rising or falling can produce unintended intermediate switch states or transient current. Check the absolute maximum supply and input-voltage limits at every operating condition, and design the logic driver so its high and low levels meet the manufacturer thresholds for the selected supply voltage.
규정 준수 정보
The available product descriptions identify the device as an industrial-grade analog switch but do not explicitly state its RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. Request current compliance documentation through the Request a Quote form.