Renesas Electronics

ISL8491EIB - 5V RS-485/RS-422 Transceiver | Renesas

Référence : ISL8491EIB ✗ Fin de vie
5 V Vdss RS-422 and RS-485 Rds(on) 14-lead SOIC Package
MOQ : 1 |

ISL8491EIB Présentation

The Renesas ISL8491EIB is a 5V, low-power, full-duplex RS-485/RS-422 interface transceiver with ±15kV ESD protection, slew-rate-limited high-speed operation, and separate receive and transmit output-enable pins. It is packaged in a 14-lead SOIC and is designed for industrial communication links requiring both differential transmit and differential receive capability.

An RS-485/RS-422 transceiver is an interface IC that converts digital logic signals into balanced differential signals and receives differential signals from a cable. These differential signaling methods improve noise immunity and allow reliable data transmission over longer cable distances than single-ended interfaces. The ISL8491EIB supports both RS-485 and RS-422 operating modes, while its full-duplex arrangement permits simultaneous transmission and reception when the bus wiring and termination network are configured appropriately.

The main device characteristics are a 5V supply, ±15kV ESD protection, low-power operation, high-speed communication with slew-rate limiting, and separate receive and transmit output-enable pins. The separate enables allow the transmitter and receiver to be controlled independently, which is useful in multidrop RS-485 networks where a node must listen while preventing bus contention. The 14-lead SOIC package is a standard surface-mount format compatible with conventional PCB assembly methods.

The ISL8491EIB is based on the Renesas ISL8491E family, which is positioned for robust industrial data links. ESD protection is particularly important because RS-485 interfaces are commonly exposed to user-accessible cables and connector transients. Slew-rate limiting helps control edge transitions on the bus and reduce unwanted high-frequency content, while the low-power design supports systems where standby and active-state efficiency are important. The exact data rate, receiver thresholds, common-mode limits, and supply-current limits should be confirmed in the manufacturer datasheet before final design release.

Typical applications include industrial automation controllers, factory data buses, building automation equipment, instrumentation links, motor-control systems, and embedded serial interfaces. The full-duplex architecture is especially appropriate for point-to-point RS-422 links and full-duplex RS-485 networks where transmit and receive paths operate simultaneously. Independent enables can support bus segmentation, controlled test modes, or systems that need to mute a receiver during certain operating states.

Designers should follow the pin-description table in the manufacturer datasheet when assigning PCB tracks, particularly for enable inputs, ground connections, driver outputs, and receiver inputs. The external network must include appropriate termination, biasing, protection, and decoupling components for the selected RS-485 or RS-422 topology. Confirm the exact ISL8491EIB ordering code, package marking, and operating-temperature limits before production release.

This page consolidates the available ISL8491EIB product information, direct replacement options, package information, and practical interface-design guidance to support faster component evaluation and sourcing decisions.

Alternatives de remplacement direct pour ISL8491EIB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec ISL8491EIB (même facteur de forme et même empreinte) — différant par ESD Protection, Package, Product Type.

Renesas Electronics
ESD Protection: 15 kV
Package: 14-pin SOIC
Product Type: RS-422/RS-485 transceiver
Comparer avec ISL8491EIB →

ISL8491EIBZ

✅ Remplacement direct
📦 14-SOIC
Same 14-SOIC RS-485/RS-422 family and 1TX/1RX architecture; ordering-suffix conditions differ by 0% in the indexed functional rating

📋 Alternative de référence (hors catalogue)

ISL8491EIB-T

✅ Remplacement direct
📦 14-SOIC
Same 14-SOIC 1TX/1RX full-duplex RS-485/RS-422 configuration; operating-temperature and lifecycle details differ by 0% in the indexed functional rating

📋 Alternative de référence (hors catalogue)

ISL8491EIBZ-T

✅ Remplacement direct
📦 14-SOIC
Same 14-SOIC 1TX/1RX full-duplex RS-485/RS-422 configuration; ordering and lifecycle conditions differ by 0% in the indexed functional rating

📋 Alternative de référence (hors catalogue)

ISL8491EIB Spécifications

Product Type Full-duplex RS-485/RS-422 transceiver
Tension d'alimentation 5 V
ESD Protection ±15 kV
Power Class Low power
Number of Drivers 1
Number of Receivers 1
Duplex Mode Full duplex
Supported Standards RS-422 and RS-485
Transmitter Output Type Slew-rate limited differential output
Transmit Output Enable Dedicated pin
Receive Output Enable Dedicated pin
Boîtier 14-lead SOIC
Nombre de broches 14 pins
Type de montage Surface mount
Plage de température de fonctionnement -40°C to +85°C
Manufacturer Renesas Electronics

Guide de configuration des broches du ISL8491EIB 14-lead soic

Configuration des broches du ISL8491EIB (boîtier 14-lead soic). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier 14-lead soic pour le ISL8491EIB

Aucune donnée de brochage détaillée disponible pour ISL8491EIB.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

ISL8491EIB convient pour 6 applications: Industrial Automation Data Buses, Factory Equipment Networking, Building Automation Controllers, Instrumentation and Sensor Gateways, Motor and Power-Control Communication, Embedded RS-422 Point-to-Point Links.

🏭

Industrial Automation Data Buses

The ISL8491EIB fits full-duplex industrial automation links that require a 5V RS-485/RS-422 interface, ±15kV ESD protection, and independent transmit and receive enables. It can sit between a controller UART and a balanced field bus, allowing the host to exchange data without relying on a single-ended serial port. The slew-rate-limited driver helps moderate edge activity on the bus, while the 14-lead SOIC supports conventional surface-mount assembly. Confirm the target baud rate and common-mode requirements in the manufacturer datasheet before selecting the associated termination and protection network.

🏭

Factory Equipment Networking

Use the ISL8491EIB in factory equipment when the communication port must support RS-422 or RS-485 over a longer balanced cable. Its full-duplex architecture supports simultaneous command transmission and status reception in point-to-point installations, while the separate enable pins let firmware isolate the driver or receiver during controlled states. The ±15kV ESD protection is useful on equipment-to-equipment cables, but connector surge protection may still be required. Validate the bus topology, grounding method, and termination locations against the actual cable length and node count.

🏠

Building Automation Controllers

The ISL8491EIB is appropriate for building automation controllers that exchange commands and sensor status over balanced RS-485 or RS-422 wiring. A 5V interface supports low-voltage embedded control systems, and the independent transmit and receive enables offer precise control over bus participation. The -40°C to +85°C temperature range suits equipment installed in temperature-variable building environments. Care should be taken at building power interfaces and long distribution runs, where the communications bus may be exposed to different ground potentials and induced transients.

📟

Instrumentation and Sensor Gateways

The ISL8491EIB can connect an embedded controller to remote instrumentation over a full-duplex RS-422 link. Separate transmit and receive enables help define operating states, while the balanced interface reduces susceptibility to common-mode noise relative to a single-ended link. Its ±15kV ESD protection adds useful protection when the transceiver is placed near an external sensor or measurement connector. The design still needs local decoupling, verified cable termination, and protection appropriate to the field-side environment.

⚡

Motor and Power-Control Communication

The ISL8491EIB supports isolated command and feedback connections in motor-control and power-conversion equipment where an embedded processor communicates with a remote controller. The 5V RS-485/RS-422 interface can carry control information while separate enables prevent unintended bus drive. Its low-power designation is useful in compact control assemblies, and its 14-lead SOIC footprint simplifies routing between a processor and a protected cable connector. Review common-mode limits, grounding, and bus protection because power-control environments can produce significant electrical transients.

🔧

Embedded RS-422 Point-to-Point Links

The ISL8491EIB is well suited to point-to-point RS-422 communication between two embedded systems because it provides a full-duplex transmitter and receiver in one 14-lead package. The independent enable inputs allow each endpoint to control direction-related states independently, which is helpful for boot, test, and maintenance modes. Slew-rate limiting helps control transition behavior on the balanced pair. For reliable operation, terminate the receiver at the cable end and route the differential conductors as a pair, with grounding and protection tailored to the application.

Where can I download the ISL8491EIB datasheet PDF?
The ISL8491EIB datasheet is available through the Renesas ISL8491E product page and the indexed datasheet documents linked on this page. The manufacturer describes a ±15kV ESD-protected, 5V, low-power, full-duplex RS-485/RS-422 transceiver in a 14-lead package. Use the manufacturer document for final pin functions, electrical limits, recommended application circuits, and ordering information.
What are the key specifications of ISL8491EIB?
The ISL8491EIB is a 5V, low-power, full-duplex RS-485/RS-422 transceiver with ±15kV ESD protection, high-speed slew-rate-limited operation, and separate transmit and receive output-enable pins. It provides one driver and one receiver in a 14-lead SOIC package. The indexed Mouser listing also identifies a -40°C to +85°C temperature range.
Where can I find the ISL8491EIB pinout?
The ISL8491EIB pin assignment is published in the manufacturer datasheet under the 14-lead package pin-description table. The family description confirms a 14-lead pinout with dedicated receive and transmit output-enable pins. Use that table for exact numbering and signal names when laying out the PCB, because this page does not reproduce the complete pin map.
Is ISL8491EIB a full-duplex RS-485 transceiver?
Yes, the ISL8491EIB is a full-duplex RS-485/RS-422 transceiver with one transmitter and one receiver. The manufacturer describes separate receive and transmit output-enable pins, allowing each direction to be controlled independently. Full-duplex operation is well suited to point-to-point RS-422 links and properly configured full-duplex RS-485 networks.
What is the ESD protection level of ISL8491EIB?
The Renesas ISL8491EIB provides ±15kV ESD protection. This rating applies to the ISL8491E family identified on the manufacturer product page. Because the complete surge, immunity, and pin-specific test conditions are not reproduced here, consult the manufacturer datasheet before applying the ±15kV figure to a particular connector or cable configuration.
What is the supply voltage of ISL8491EIB?
The ISL8491EIB operates from a 5V supply. This value is stated in the manufacturer product-page description and is also reflected in the indexed distributor identification of the device as a 5V RS-485/RS-422 interface IC. Confirm absolute maximum and recommended supply limits in the manufacturer datasheet during schematic review.
ISL8491EIB vs ISL8491EIBZ - which is the correct ordering code?
The ISL8491EIB is the base device designation, while ISL8491EIBZ is an indexed Renesas/Intersil ordering variant. The manufacturer family entry identifies the ISL8491E, and Mouser indexes ISL8491EIBZ as a 14-lead, 5V, one-transmit/one-receive RS-485/RS-422 interface IC. Verify the package, temperature, and marking requirements before treating the suffix variants as interchangeable.
What can replace the obsolete ISL8491EIB?
The closest indexed replacements are the Renesas ISL8491EIB-T, ISL8491EIBZ-T, and ISL8491EIBZ orderings, all associated with the same 14-SOIC RS-485/RS-422 family. The ISL8491EIB-T is explicitly identified as obsolete, so lifecycle status, temperature grade, and exact pin configuration must be checked before replacement. No verified cross-brand drop-in replacement was identified.
Is ISL8491EIB the same as ISL8491EIBZ?
ISL8491EIB and ISL8491EIBZ belong to the same Renesas ISL8491E transceiver family and are associated with a 14-lead SOIC package. However, the ordering suffix can encode temperature grade, packaging, or other commercial conditions. Compare the manufacturer ordering table, top-marking scheme, and datasheet limits before substituting one code for the other.
When should I choose ISL8491EIB over another RS-485 transceiver?
Choose the ISL8491EIB when the design requires a 5V, full-duplex RS-485/RS-422 interface with ±15kV ESD protection and independent transmit and receive enables. It is particularly appropriate for point-to-point industrial links, factory equipment, and building automation. Select another device when the design requires a different data rate, supply range, package, half-duplex architecture, isolation, or automotive qualification.
Is ISL8491EIB suitable for industrial automation equipment?
The ISL8491EIB is suitable for many industrial automation communication interfaces because it supports RS-485 and RS-422 at 5V, includes ±15kV ESD protection, and provides independent output enables. Its -40°C to +85°C range also suits extended industrial environments. The complete electrical limits and isolation requirements should still be checked against the target equipment standard.
How should termination and biasing be designed for ISL8491EIB?
Termination and biasing must be sized for the exact RS-485 or RS-422 topology rather than copied blindly between designs. Place termination at the physical cable ends, use a bias network only where required, and route the differential pair as a tightly coupled pair to minimize common-mode conversion. The manufacturer application circuit should guide connector protection, grounding, and enable-state requirements.
Does ISL8491EIB need external transceiver protection?
The ISL8491EIB already includes ±15kV ESD protection, but that does not eliminate the need to evaluate the complete cable and connector path. Long cables and field-accessible connectors may require additional surge, clamping, or isolation components. Select those parts using the applicable surge waveform and common-mode limits rather than the ESD rating alone.
Where can I buy ISL8491EIB?
Use the Request a Quote form on this page to ask for ISL8491EIB availability, current condition, lead time, and sourcing options. Because the ISL8491EIB is an obsolete order code, confirm whether the request should be fulfilled with the related Renesas ISL8491EIB-T, ISL8491EIBZ-T, or ISL8491EIBZ ordering rather than assuming all suffix codes have the same commercial status.
What is the price of ISL8491EIB?
Current unit pricing for the obsolete ISL8491EIB should be requested through the Request a Quote form on this page. The indexed distributor pages cover availability and product identity but do not expose an explicit quantity-break table for this exact base order code. A quote request allows XAIPART to confirm the correct suffix, condition, quantity, and current sourcing path.
What is the lead time and stock status for ISL8491EIB?
Stock, minimum order quantity, and lead time for the obsolete ISL8491EIB should be confirmed through the Request a Quote form on this page. The family remains represented by several Renesas orderings, but the base ISL8491EIB and its suffix variants can have different lifecycle and inventory conditions. Provide the required quantity and target suffix when requesting a quote.

Données de référence d'ingénierie pour ISL8491EIB — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose ISL8491EIB when an existing design requires the base Renesas 14-lead SOIC full-duplex RS-485/RS-422 interface, 5V operation, independent transmit and receive enables, and the ISL8491E family's ±15kV ESD protection. Because the order code is obsolete and the ISL8491EIB-T is also identified as obsolete, use a Request a Quote request to determine whether a related ISL8491EIBZ or ISL8491EIBZ-T order can satisfy the exact mechanical, temperature, and marking requirements. Select a different transceiver when the design requires a different package, higher speed, broader supply range, half-duplex operation, galvanic isolation, or automotive qualification. No verified cross-brand pin-to-pin replacement was identified, so an engineering review is required before introducing a second-source device.

Comparaison avec les alternatives

Paramètre Ce produit ISL8491EIBZ ISL8491EIB-T ISL8491EIBZ-T
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 14-SOIC 14-SOIC - same 14-SOIC - same 14-SOIC - same
Transceiver Type Full-duplex RS-485/RS-422 Full-duplex RS-485/RS-422 Full RS-422/RS-485 Full RS-422/RS-485
Supply Voltage 5 V 5 V 5 V 5 V
ESD Protection ±15 kV ±15 kV family rating ±15 kV family rating ±15 kV family rating
Driver / Receiver Count 1 transmitter / 1 receiver 1 transmitter / 1 receiver 1 transmitter / 1 receiver 1 transmitter / 1 receiver
Output Enables Separate receive and transmit enables Separate receive and transmit enables Separate receive and transmit enables Separate receive and transmit enables

Principaux différenciateurs

  • Independent communication-direction control (vs ISL8491EIB-T)
  • Matched 5V differential interface architecture (vs ISL8491EIBZ)
  • Protected industrial interface family (vs ISL8491EIBZ-T)

Notes de conception

Route the RS-485/RS-422 differential pair as a tightly coupled pair over a continuous reference plane. Keep the transceiver, protection network, and connector in the same signal region, and minimize stubs from the cable connector to the transceiver. Place receive termination at the receiver end rather than beside the transmitter when the topology requires only one termination point.

Do not substitute an ordering suffix without checking temperature grade, package form, marking, and lifecycle status. The ISL8491EIB, ISL8491EIBZ, ISL8491EIB-T, and ISL8491EIBZ-T appear in indexed 14-SOIC listings, but the suffix can affect commercial conditions and qualification. Complete a manufacturer ordering-table comparison before approving any replacement for production.

Use the slew-rate-limited outputs with a controlled differential impedance and appropriate cable termination. Avoid long unprotected traces between the transceiver and protection components, and verify that enable inputs remain in defined states during reset so the driver cannot contend with another node. For field cables, evaluate additional surge protection and common-mode transients separately from the ±15kV ESD rating.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The ISL8491EIB is an RS-485/RS-422 interface IC rather than an automotive-qualified component. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses were not stated in the indexed product information.

Recherches associées

ISL8491EIB datasheet ISL8491EIB pinout ISL8491EIB datasheet pdf ISL8491EIB replacement ISL8491EIB equivalent ISL8491EIB cross reference Renesas ISL8491EIB ISL8491EIB 5V transceiver ISL8491EIB 14-SOIC ISL8491EIB RS-485 application circuit ISL8491EIB vs ISL8491EIBZ ISL8491EIB price ISL8491EIB stock ISL8491EIB footprint

Composants & termes associés

Renesas Electronics ISL8491EIB ISL8491EIBZ ISL8491EIB-T ISL8491EIBZ-T RS-485 RS-422 interface transceiver line driver line receiver balanced differential signaling full duplex 14-SOIC SOIC family surface-mount package ESD protection slew-rate limiting transmit output enable receive output enable industrial automation factory automation building automation 5V transceiver semiconductor
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ