ISL8491EIB - 5V RS-485/RS-422 Transceiver | Renesas
Артикул: ISL8491EIB ✗ Снят с производстваISL8491EIB Обзор
An RS-485/RS-422 transceiver is an interface IC that converts digital logic signals into balanced differential signals and receives differential signals from a cable. These differential signaling methods improve noise immunity and allow reliable data transmission over longer cable distances than single-ended interfaces. The ISL8491EIB supports both RS-485 and RS-422 operating modes, while its full-duplex arrangement permits simultaneous transmission and reception when the bus wiring and termination network are configured appropriately.
The main device characteristics are a 5V supply, ±15kV ESD protection, low-power operation, high-speed communication with slew-rate limiting, and separate receive and transmit output-enable pins. The separate enables allow the transmitter and receiver to be controlled independently, which is useful in multidrop RS-485 networks where a node must listen while preventing bus contention. The 14-lead SOIC package is a standard surface-mount format compatible with conventional PCB assembly methods.
The ISL8491EIB is based on the Renesas ISL8491E family, which is positioned for robust industrial data links. ESD protection is particularly important because RS-485 interfaces are commonly exposed to user-accessible cables and connector transients. Slew-rate limiting helps control edge transitions on the bus and reduce unwanted high-frequency content, while the low-power design supports systems where standby and active-state efficiency are important. The exact data rate, receiver thresholds, common-mode limits, and supply-current limits should be confirmed in the manufacturer datasheet before final design release.
Typical applications include industrial automation controllers, factory data buses, building automation equipment, instrumentation links, motor-control systems, and embedded serial interfaces. The full-duplex architecture is especially appropriate for point-to-point RS-422 links and full-duplex RS-485 networks where transmit and receive paths operate simultaneously. Independent enables can support bus segmentation, controlled test modes, or systems that need to mute a receiver during certain operating states.
Designers should follow the pin-description table in the manufacturer datasheet when assigning PCB tracks, particularly for enable inputs, ground connections, driver outputs, and receiver inputs. The external network must include appropriate termination, biasing, protection, and decoupling components for the selected RS-485 or RS-422 topology. Confirm the exact ISL8491EIB ordering code, package marking, and operating-temperature limits before production release.
This page consolidates the available ISL8491EIB product information, direct replacement options, package information, and practical interface-design guidance to support faster component evaluation and sourcing decisions.
Аналоги без доработки для ISL8491EIB — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ISL8491EIB (тот же форм-фактор и посадочное место) — отличается по ESD Protection, Package, Product Type.
ISL8491EIBZ
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ISL8491EIB-T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ISL8491EIBZ-T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
ISL8491EIB Характеристики
| Product Type | Full-duplex RS-485/RS-422 transceiver |
| Напряжение питания | 5 V |
| ESD Protection | ±15 kV |
| Power Class | Low power |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Duplex Mode | Full duplex |
| Supported Standards | RS-422 and RS-485 |
| Transmitter Output Type | Slew-rate limited differential output |
| Transmit Output Enable | Dedicated pin |
| Receive Output Enable | Dedicated pin |
| Корпус | 14-lead SOIC |
| Число выводов | 14 pins |
| Тип монтажа | Surface mount |
| Диапазон рабочих температур | -40°C to +85°C |
| Manufacturer | Renesas Electronics |
Руководство по цоколевке ISL8491EIB в корпусе 14-lead soic
Цоколевка для ISL8491EIB (корпус 14-lead soic). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для ISL8491EIB.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
ISL8491EIB подходит для 6 применениеs: Industrial Automation Data Buses, Factory Equipment Networking, Building Automation Controllers, Instrumentation and Sensor Gateways, Motor and Power-Control Communication, Embedded RS-422 Point-to-Point Links.
Industrial Automation Data Buses
The ISL8491EIB fits full-duplex industrial automation links that require a 5V RS-485/RS-422 interface, ±15kV ESD protection, and independent transmit and receive enables. It can sit between a controller UART and a balanced field bus, allowing the host to exchange data without relying on a single-ended serial port. The slew-rate-limited driver helps moderate edge activity on the bus, while the 14-lead SOIC supports conventional surface-mount assembly. Confirm the target baud rate and common-mode requirements in the manufacturer datasheet before selecting the associated termination and protection network.
Рекомендуется
Factory Equipment Networking
Use the ISL8491EIB in factory equipment when the communication port must support RS-422 or RS-485 over a longer balanced cable. Its full-duplex architecture supports simultaneous command transmission and status reception in point-to-point installations, while the separate enable pins let firmware isolate the driver or receiver during controlled states. The ±15kV ESD protection is useful on equipment-to-equipment cables, but connector surge protection may still be required. Validate the bus topology, grounding method, and termination locations against the actual cable length and node count.
Рекомендуется
Building Automation Controllers
The ISL8491EIB is appropriate for building automation controllers that exchange commands and sensor status over balanced RS-485 or RS-422 wiring. A 5V interface supports low-voltage embedded control systems, and the independent transmit and receive enables offer precise control over bus participation. The -40°C to +85°C temperature range suits equipment installed in temperature-variable building environments. Care should be taken at building power interfaces and long distribution runs, where the communications bus may be exposed to different ground potentials and induced transients.
Рекомендуется
Instrumentation and Sensor Gateways
The ISL8491EIB can connect an embedded controller to remote instrumentation over a full-duplex RS-422 link. Separate transmit and receive enables help define operating states, while the balanced interface reduces susceptibility to common-mode noise relative to a single-ended link. Its ±15kV ESD protection adds useful protection when the transceiver is placed near an external sensor or measurement connector. The design still needs local decoupling, verified cable termination, and protection appropriate to the field-side environment.
Рекомендуется
Motor and Power-Control Communication
The ISL8491EIB supports isolated command and feedback connections in motor-control and power-conversion equipment where an embedded processor communicates with a remote controller. The 5V RS-485/RS-422 interface can carry control information while separate enables prevent unintended bus drive. Its low-power designation is useful in compact control assemblies, and its 14-lead SOIC footprint simplifies routing between a processor and a protected cable connector. Review common-mode limits, grounding, and bus protection because power-control environments can produce significant electrical transients.
Рекомендуется
Embedded RS-422 Point-to-Point Links
The ISL8491EIB is well suited to point-to-point RS-422 communication between two embedded systems because it provides a full-duplex transmitter and receiver in one 14-lead package. The independent enable inputs allow each endpoint to control direction-related states independently, which is helpful for boot, test, and maintenance modes. Slew-rate limiting helps control transition behavior on the balanced pair. For reliable operation, terminate the receiver at the cable end and route the differential conductors as a pair, with grounding and protection tailored to the application.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ISL8491EIB — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ISL8491EIBZ | ISL8491EIB-T | ISL8491EIBZ-T |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 14-SOIC | 14-SOIC - same | 14-SOIC - same | 14-SOIC - same |
| Transceiver Type | Full-duplex RS-485/RS-422 | Full-duplex RS-485/RS-422 | Full RS-422/RS-485 | Full RS-422/RS-485 |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V |
| ESD Protection | ±15 kV | ±15 kV family rating | ±15 kV family rating | ±15 kV family rating |
| Driver / Receiver Count | 1 transmitter / 1 receiver | 1 transmitter / 1 receiver | 1 transmitter / 1 receiver | 1 transmitter / 1 receiver |
| Output Enables | Separate receive and transmit enables | Separate receive and transmit enables | Separate receive and transmit enables | Separate receive and transmit enables |
Ключевые отличия
- Independent communication-direction control (против ISL8491EIB-T)
- Matched 5V differential interface architecture (против ISL8491EIBZ)
- Protected industrial interface family (против ISL8491EIBZ-T)
Заметки по проектированию
Route the RS-485/RS-422 differential pair as a tightly coupled pair over a continuous reference plane. Keep the transceiver, protection network, and connector in the same signal region, and minimize stubs from the cable connector to the transceiver. Place receive termination at the receiver end rather than beside the transmitter when the topology requires only one termination point.
Do not substitute an ordering suffix without checking temperature grade, package form, marking, and lifecycle status. The ISL8491EIB, ISL8491EIBZ, ISL8491EIB-T, and ISL8491EIBZ-T appear in indexed 14-SOIC listings, but the suffix can affect commercial conditions and qualification. Complete a manufacturer ordering-table comparison before approving any replacement for production.
Use the slew-rate-limited outputs with a controlled differential impedance and appropriate cable termination. Avoid long unprotected traces between the transceiver and protection components, and verify that enable inputs remain in defined states during reset so the driver cannot contend with another node. For field cables, evaluate additional surge protection and common-mode transients separately from the ±15kV ESD rating.
Информация о соответствии
The ISL8491EIB is an RS-485/RS-422 interface IC rather than an automotive-qualified component. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses were not stated in the indexed product information.