Analog Devices

ADM3491AN-1 - 3.3V 20Mbps RS-485/RS-422 Transceiver | Analog Devices

Référence : ADM3491AN-1 ✓ Actif
3.3 V Vdss EIA RS-485 and RS-422 Rds(on) 14-lead SOIC Package
MOQ : 1 |

ADM3491AN-1 Présentation

The Analog Devices ADM3491AN-1 is a low-power differential line transceiver operating from a single 3.3 V supply, with a maximum data rate of 20 Mbps in a 14-lead SOIC package. It combines a differential line driver and differential line receiver for balanced RS-485 and RS-422 communication, while a shutdown mode helps reduce consumption in power-sensitive systems.

A differential line transceiver is an interface IC that transmits data across balanced, noise-resistant lines while receiving signals with high common-mode rejection. RS-485 supports robust multipoint communication over relatively long cable runs, whereas RS-422 emphasizes full-duplex point-to-point links. Within the interface hierarchy, the ADM3491AN-1 belongs to the RS-485/RS-422 transceiver class, connects digital controllers to physical communication lines, and operates as part of a broader industrial communications system.

Key features include a single 3.3 V power supply, low-power operation, full-duplex communication, and a shutdown function. The identified low-power figure is 840 uA, while the cited data rate reaches 20 Mbps. Its differential driver and receiver architecture provides a practical balance between communication throughput, power consumption, and system complexity. The separate driver and receiver paths support simultaneous transmission and reception in full-duplex RS-422 networks.

The ADM3491 family is intended for balanced data transmission and supports both Electronic Industries Association RS-485 and RS-422 interfaces. Communication protocols can use the transceiver as the physical-layer interface beneath UART, industrial automation, instrumentation, or industrial Ethernet equipment. The 3.3 V supply also allows direct integration with modern low-voltage controllers, reducing the need for level-shift or separate line-driver circuitry.

Typical uses include industrial control links, factory automation nodes, sensor and instrumentation networks, building-control equipment, and data-acquisition systems. In these applications, the balanced line helps reject common-mode noise encountered near motors, relays, and long cables. The 20 Mbps capability is useful for links that require higher throughput than conventional low-speed RS-485 nodes while retaining the simplicity of a serial differential interface.

PCB design should preserve the differential signal path, use a continuous ground reference, and place termination and protection components near the line interface. The shutdown control should be driven only after the transmitter and receiver signals are placed in a safe state. Operating temperature, enable polarity, receiver fail-safe behavior, and electrical limits should be confirmed against the manufacturer datasheet before production release.

This page combines the device function, verified operating characteristics, package information, interface-design guidance, and comparison criteria for evaluating the ADM3491 family against compatible interface transceivers.

Alternatives de remplacement direct pour ADM3491AN-1 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec ADM3491AN-1 (même facteur de forme et même empreinte) — différant par Mounting Type, Package, Supply Voltage, Logic Compatibility, Maximum Data Rate.

Analog Devices
Mounting Type: Through-hole
Package: 12-pin PDIP
Supply Voltage: 3.3 V ± 0.3 V
Comparer avec ADM3491AN-1 →
Analog Devices
Logic Compatibility: 5 V logic interoperable
Maximum Data Rate: 10 Mbps
Comparer avec ADM3491AN-1 →

ADM3491AN

✅ Remplacement direct
Analog Devices
📦 14-lead SOIC
3.3 V ± 0.3 V · 20 Mbps · 840 µA · 2 nA · 19 kΩ · 50 transceivers · Full duplex · EIA RS-485 and EIA RS-422

Contactez-nous pour le prix

Voir la fiche technique →

ADM3491ARZ

✅ Remplacement direct
Analog Devices
📦 14-lead SOIC
Full-duplex differential line transceiver · EIA RS-422 and EIA RS-485 · 3.3 V · 10 Mbps · 19 kΩ · 50 transceivers · 840 µA · 2 nA

Contactez-nous pour le prix

Voir la fiche technique →

ADM3491-1

✅ Remplacement direct
📦 14-lead SOIC
Same 3.3 V differential RS-485/RS-422 transceiver family and 14-lead SOIC format; the -1 family designation must be checked against required speed and ordering parameters.

📋 Alternative de référence (hors catalogue)

ADM3491AN-1 Spécifications

Product Type Low-power differential RS-485/RS-422 line transceiver
Tension d'alimentation 3.3 V
Maximum Data Rate 20 Mbps
Low-Power Consumption 840 uA
Supported Standards EIA RS-485 and RS-422
Communication Mode Full duplex
Driver Architecture Differential line driver
Receiver Architecture Differential line receiver
Power-Down Feature Yes, shutdown mode
Boîtier 14-lead SOIC
Type de montage Surface mount

Guide de configuration des broches du ADM3491AN-1 14-lead soic

Configuration des broches du ADM3491AN-1 (boîtier 14-lead soic). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.

Schéma de brochage du boîtier 14-lead soic pour le ADM3491AN-1

Aucune donnée de brochage détaillée disponible pour ADM3491AN-1.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

ADM3491AN-1 convient pour 6 applications: Industrial Automation Serial Links, Factory Sensor Networks, Instrumentation and Test Equipment, Building Control Networks, Data Acquisition Systems, Power-Sensitive Communication Modules.

🏭

Industrial Automation Serial Links

The ADM3491AN-1 fits industrial automation equipment that needs a balanced, noise-resistant communication interface on a 3.3 V power rail. Its integrated differential driver and receiver support full-duplex RS-422 or RS-485 links, while the cited 20 Mbps capability provides more throughput than required for slow sensor polling. The low-power figure of 840 uA and shutdown mode help control system consumption when a node is inactive. In a controller or remote I/O module, the transceiver can connect a serial processor directly to a field cable, subject to the manufacturer’s enable, termination, and loading requirements.

🧩

Factory Sensor Networks

The ADM3491AN-1 is suitable for factory sensor networks where cables run near relays, motor drives, and switching equipment. Differential signaling rejects common-mode noise better than a single-ended serial interface, while the 3.3 V supply can simplify integration with sensor controllers and gateways. Its full-duplex architecture can support dedicated transmit and receive paths where RS-422 point-to-point wiring is used. The 840 uA cited low-power figure makes the device relevant to distributed nodes, although overall node consumption must include the host processor, isolation, and cable-driver loading.

🔧

Instrumentation and Test Equipment

The ADM3491AN-1 supports balanced serial connections in instrumentation and test equipment where a compact, low-voltage physical-layer interface is required. The differential receiver and driver are appropriate for communicating between a controller and external measurement equipment over RS-422, while the transceiver also supports RS-485 networks. Its listed 20 Mbps rate accommodates data-intensive instrument links and provides margin for shorter, well-controlled connections. The shutdown function can disable the interface during idle periods, and the 14-lead SOIC package simplifies assembly on conventional mixed-signal boards.

🏠

Building Control Networks

The ADM3491AN-1 can serve as the balanced line interface in building-control equipment connected to distributed sensors, actuators, or access-control nodes. A single 3.3 V supply is convenient for low-power controllers, while differential signaling improves robustness against common-mode disturbances found in building wiring. The device supports RS-485 and RS-422, allowing designers to match the topology to cable length and communication architecture. Its full-duplex operation supports simultaneous command and status traffic when separate balanced pairs are used, and shutdown mode can reduce consumption during inactive periods.

📊

Data Acquisition Systems

The ADM3491AN-1 is appropriate for distributed data-acquisition systems that transfer sensor, status, or configuration data over balanced copper links. Its differential driver and receiver reduce susceptibility to common-mode noise, and the 3.3 V operation can interface directly with modern embedded controllers. The cited 20 Mbps capability is useful where acquisition nodes transmit compact data bursts or where short laboratory and industrial cables support higher rates. Designers should use the datasheet timing limits to preserve adequate rise and fall time at the selected baud rate.

🔋

Power-Sensitive Communication Modules

The ADM3491AN-1 fits compact communication modules that prioritize low power and a single 3.3 V supply. Its low-power figure of 840 uA, differential communication paths, and shutdown mode allow the physical interface to remain efficient while inactive. The device can bridge a low-voltage controller to an RS-485 or RS-422 network without adding a separate line-driver package. Because the 20 Mbps maximum is a headline capability rather than a universal cable-rate guarantee, designers should select baud rate and cable length together and apply the appropriate termination and protection network.

What is the operating voltage of the ADM3491AN-1?
The ADM3491AN-1 operates from a single 3.3 V power supply. According to the Analog Devices ADM3491 product page, the device is a low-power differential transceiver intended for power-sensitive balanced communications. This supply arrangement allows direct use with 3.3 V digital controllers and simplifies mixed-signal board partitioning while the shutdown mode provides an additional way to reduce current when the interface is not active.
What is the maximum data rate of ADM3491AN-1?
The ADM3491AN-1 supports a maximum data rate of 20 Mbps. The listed ADM3491AN data identifies a 3.3 V, full-duplex RS-485 transceiver rated at 20 Mbps, while the Analog Devices family page describes the family as a low-power RS-485/RS-422 transceiver. Confirm the complete timing, enable, and loading conditions in the manufacturer datasheet before using the maximum rate on a specific cable.
Where can I download the ADM3491AN-1 datasheet PDF?
The official ADM3491AN-1 documentation begins on the Analog Devices ADM3491 product page at https://www.analog.com/en/products/adm3491.html. From that page, open the datasheet and select the ordering-code information for the 14-lead SOIC version. Use the manufacturer document for the authoritative pin description, electrical limits, timing diagrams, shutdown behavior, and recommended application circuit.
Where can I find the ADM3491AN-1 pinout?
The ADM3491AN-1 pinout is published in the pin-description table and package drawing in the Analog Devices ADM3491 datasheet. The device is associated with a 14-lead SOIC package. Assign PCB nets from that table rather than inferring connections from transceiver family conventions, particularly for driver-enable, receiver-enable, ground, supply, and differential bus pins.
What interfaces does the ADM3491AN-1 support?
The ADM3491AN-1 supports balanced EIA RS-485 and RS-422 communications through an integrated differential driver and differential receiver. According to Analog Devices, the ADM3491-1 family is intended for balanced data transmission and complies with both RS-485 and RS-422 requirements. The actual bus topology, termination, biasing, and operating mode must be selected from the corresponding interface standard.
Is ADM3491AN-1 suitable for low-power industrial applications?
Yes, the ADM3491AN-1 suits power-sensitive 3.3 V industrial and instrumentation systems because it combines low-power operation, a cited 840 uA consumption figure, and shutdown capability. Its differential RS-485 or RS-422 interface also supports noise-robust balanced links. The transceiver should still be evaluated against the complete module power budget, cable length, data rate, and thermal environment.
ADM3491AN-1 vs ADM3491AN - which is the correct ordering code?
The ADM3491AN-1 and ADM3491AN appear within the same Analog Devices ADM3491 family, but the ordering suffix must be matched to the required temperature, packaging, and qualification conditions. The ADM3491AN listing identifies a 3.3 V, full-duplex, 20 Mbps RS-485 transceiver, while the ADM3491AN-1 page is the exact target ordering code. Confirm the ordering table before treating either listing as interchangeable.
When should I choose ADM3491AN-1 over a lower-speed RS-485 transceiver?
Choose the ADM3491AN-1 when a balanced 3.3 V link must support data rates up to the cited 20 Mbps limit. It is especially relevant for full-duplex industrial links, instrumentation, and factory systems where throughput matters. A lower-speed transceiver may be preferable when the application uses slow polling and prioritizes lower power or a different bus architecture, but it cannot be assumed to preserve the ADM3491AN-1 data-rate capability.
What can replace the ADM3491AN-1 on the same PCB?
The closest confirmed same-package choice is another ordering configuration in the ADM3491 family, such as ADM3491AN or ADM3491ARZ in a 14-lead SOIC package. Compatibility still depends on the exact speed grade, temperature range, enable logic, and shutdown behavior. Use the manufacturer ordering table and compare those specifications before applying any replacement to production hardware.
What is the best Analog Devices equivalent for ADM3491AN-1?
The best Analog Devices-family equivalent is an ADM3491 ordering code that retains the same 14-lead SOIC pinout, 3.3 V operation, differential driver and receiver, shutdown function, and required data rate. ADM3491AN and ADM3491ARZ are the closest identified alternatives, but suffix-specific electrical and temperature requirements must be checked. A same-brand alternative is preferable only when its ordering parameters are identical.
Where to buy ADM3491AN-1 online?
Use the Request a Quote form on this page to request ADM3491AN-1 availability, lot quantity, and lead time. The form is the appropriate route for a quote based on the exact ADM3491AN-1 ordering code and its 14-lead SOIC package. Clearly state the required quantity, delivery location, and whether reel, tray, or another approved packing format is needed.
What is the price of ADM3491AN-1?
The current unit price for ADM3491AN-1 should be obtained through the Request a Quote form on this page. Quote processing depends on the exact quantity, supply condition, packaging format, and delivery requirements. Submit the target MPN and quantity to receive current pricing and commercial terms without relying on a stale catalog amount.
What is the lead time for ADM3491AN-1?
The current lead time for ADM3491AN-1 is handled through the Request a Quote form on this page. The form should be submitted with the required quantity, date code preference, packaging format, and ship-to location. These details allow the order to be evaluated against actual component availability instead of assuming a fixed factory or distribution lead time.
Is ADM3491AN-1 in stock?
Current ADM3491AN-1 stock status should be confirmed through the Request a Quote form on this page. Include the required quantity and packaging preference in the request. The manufacturer lists the ADM3491 as a production product, but order-specific inventory and lead time should not be inferred from general product status.
What are the key specifications of ADM3491AN-1 that engineers should know?
The ADM3491AN-1 is a 3.3 V, low-power, full-duplex differential transceiver for RS-485 and RS-422 balanced links, with a cited maximum rate of 20 Mbps and low-power figure of 840 uA. It integrates a differential driver and receiver and includes shutdown mode in a 14-lead SOIC package. These characteristics place it between low-speed field-bus transceivers and faster short-reach balanced-data interfaces.
Can ADM3491AN-1 be used in a full-duplex RS-422 link?
Yes, the ADM3491AN-1 can support a full-duplex balanced RS-422 link because it contains both a differential line driver and a differential line receiver. The 3.3 V supply and shutdown mode are useful in compact, power-sensitive equipment. Verify enable timing, termination values, driver-loading limits, and grounding against the manufacturer datasheet before finalizing the circuit.

Données de référence d'ingénierie pour ADM3491AN-1 — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose ADM3491AN-1 for a compact 3.3 V system that needs a full-duplex differential RS-485 or RS-422 interface and may benefit from the cited 20 Mbps data rate. Its differential driver and receiver, shutdown mode, and 14-lead SOIC package make it appropriate for industrial controllers, instrumentation, and low-power communication modules. Select ADM3491AN when that ordering code satisfies the required temperature, qualification, and packing conditions; select ADM3491ARZ when its specific ordering parameters and sourcing format fit the design. ADM3491-1 is another family option, but its exact speed grade and ordering conditions should be checked. Before final selection, verify enable polarity, electrical limits, receiver fail-safe operation, and shutdown behavior against the manufacturer datasheet. The alternatives share the same family footprint, but package identity alone does not replace a complete parameter review.

Comparaison avec les alternatives

Paramètre Ce produit ADM3491AN ADM3491ARZ ADM3491-1
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Package 14-lead SOIC 14-lead SOIC 14-lead SOIC 14-lead SOIC
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V
Communication Mode Full duplex Full duplex Full duplex Full duplex
Supported Standards EIA RS-485 and RS-422 EIA RS-485 and RS-422 EIA RS-485 and RS-422 EIA RS-485 and RS-422
Driver and Receiver Architecture Differential driver and differential receiver Differential driver and differential receiver Differential driver and differential receiver Differential driver and differential receiver
Shutdown Function Yes Yes Yes Yes
Lifecycle Status Active Active Active Active

Principaux différenciateurs

  • Higher cited throughput within the ADM3491 family ordering options (vs ADM3491ARZ)
  • Single low-voltage supply simplifies controller integration (vs ADM3491-1)
  • Full-duplex balanced interface with integrated shutdown (vs ADM3491AN)

Notes de conception

Route the differential bus as a tightly matched pair with continuous ground beneath it, and keep the transceiver interface section away from switching nodes and high-current return paths. Place termination, biasing, and protection components near the bus connector or transceiver pins, whichever is electrically appropriate for the topology. Maintain a low-impedance ground return beneath the pair and avoid long stubs because they can degrade signal integrity and alter the usable bus rate.

Decouple the 3.3 V supply close to the transceiver supply pins with the capacitance and voltage rating specified by the manufacturer. Keep the shutdown control in a defined state during reset so the transmitter cannot drive the bus unexpectedly. Before enabling the driver, apply the required bus-idle condition so that multiple nodes do not conflict during startup. Account for the transceiver’s load current, supply noise, and line-driver dissipation in the rail and thermal design.

Do not select RS-485 and RS-422 termination and biasing as if the interfaces were electrically identical. RS-485 commonly uses termination at both cable ends and may require fail-safe biasing, while a full-duplex RS-422 point-to-point link normally uses termination only at the receiver end. Confirm enable polarity, receiver output state during shutdown, and cable-length-versus-baud-rate limits in the ADM3491 manufacturer datasheet before releasing the PCB.

The cited 20 Mbps capability should be treated as a device-level maximum rather than a guarantee for every cable, topology, or protection network. Use controlled-impedance wiring, minimize stub lengths, and evaluate rise and fall time at the receiver when operating near the upper rate limit. If the application requires longer cables or lower power, reduce the baud rate and validate the complete bus with representative cable lengths and grounding conditions.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The ADM3491 product materials identify the family as a 3.3 V RS-485/RS-422 transceiver, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was confirmed for the exact ADM3491AN-1 ordering code.

Recherches associées

ADM3491AN-1 datasheet ADM3491AN-1 pinout ADM3491AN-1 datasheet pdf ADM3491AN-1 14-SOIC pinout ADM3491AN-1 equivalent ADM3491AN-1 replacement ADM3491AN-1 cross reference ADM3491AN-1 vs ADM3491AN ADM3491AN-1 application circuit ADM3491AN-1 RS-485 transceiver Analog Devices ADM3491AN-1 ADM3491AN-1 price ADM3491AN-1 stock ADM3491AN-1 lead time ADM3491AN-1 footprint

Composants & termes associés

Analog Devices ADM3491AN-1 ADM3491AN ADM3491ARZ ADM3491-1 RS-485 transceiver RS-422 transceiver differential line transceiver differential line driver differential line receiver balanced data transmission full duplex half duplex EIA RS-485 EIA RS-422 14-lead SOIC SOIC package family surface-mount package 3.3 V power supply 20 Mbps data rate 840 uA low-power figure shutdown mode common-mode rejection industrial automation factory automation
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ