LM2903PWR - Dual Open-Collector Comparator | Texas Instruments
Référence : LM2903PWR ✓ ActifLM2903PWR Présentation
A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input rises above the inverting input. In the larger semiconductor hierarchy, the LM2903 belongs to the comparator and analog IC family, where its differential inputs, open-collector outputs, and wide supply tolerance support robust sensing across industrial voltage ranges.
The LM2903PWR provides two independent comparison channels in one package. Its open-collector outputs can sink output current while remaining in a high-impedance state when inactive, allowing pull-up resistors to set the logic-high voltage and multiple comparator outputs to share a bus when wired appropriately. Rail-to-rail input operation extends the usable common-mode range toward the supply limits, which is valuable in battery-powered and industrial designs.
The improved LM2903B family associated with this device is specified for operation up to 38V, an ESD rating of 2kV HBM, input offset voltage as low as 0.37mV, input bias current as low as 3.5nA, supply current of 200µA per comparator, and response time of 1µs. These characteristics improve on older LM393-family performance while retaining the established LM2903 function and pin arrangement.
Typical uses include DC threshold monitors, overvoltage and undervoltage detection, sensor conditioning, window comparators, and industrial control logic. In a typical application, each comparator evaluates a signal against a reference generated by a resistor divider, while external pull-up resistors convert the open-collector output into a valid logic-high state.
Layout should keep input traces short, route sensitive comparison nodes away from switching-node currents, and place input and reference-network components close to the device. A common ground reference and stable bypass capacitance are essential because comparator decisions depend on the difference between two input voltages.
This page combines manufacturer device information, verified distributor listings, package identification, replacement analysis, and application-focused design guidance. It also distinguishes confirmed drop-in options from alternatives that cannot be installed on the same 8-pin TSSOP footprint without redesign.
Alternatives de remplacement direct pour LM2903PWR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM2903PWR (même facteur de forme et même empreinte) — différant par Package, Input Bias Current, Operating Temperature Range, Comparator Type, Number of Channels.
LM2903PWRG4
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2903PWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2903PWR Valeurs maximales et caractéristiques électriques
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Type de sortie | Open-collector |
| Input Common-Mode Range | Rail-to-rail |
| Supply Voltage Range | ±18V / 36V total |
| Maximum Rating of LM2903B Family | Up to 38V |
| Input Offset Voltage | 0.37mV maximum |
| Input Bias Current | 3.5nA maximum |
| Courant d'alimentation | 200µA per comparator |
| Response Time | 1µs |
| ESD Rating | 2kV HBM |
| Boîtier | 8-pin TSSOP |
| Type de montage | Surface mount |
| Statut RoHS | RoHS Compliant |
Guide de configuration des broches du LM2903PWR 8-pin tssop
Configuration des broches du LM2903PWR (boîtier 8-pin tssop). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour LM2903PWR.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
LM2903PWR convient pour 6 applications: Industrial Overvoltage Detection, Battery Voltage Window Monitor, Sensor Signal Conditioning, Control System Limit Detector, Automotive-Level Logic Interface, Analog-to-Digital Conversion Front End.
Industrial Overvoltage Detection
The LM2903PWR fits industrial voltage-monitoring circuits because its dual open-collector comparators can evaluate upper and lower system thresholds against separate references. Each channel compares a divided feedback voltage with a reference, and the open-collector outputs can directly pull down an alarm or interlock line. The associated LM2903B specifications include operation up to 38V, 0.37mV maximum input offset voltage, and 3.5nA maximum input bias current, helping preserve threshold accuracy. The 8-pin TSSOP package also reduces board area compared with two separate single comparators. Designers should account for input and output current, pull-up resistance, and the comparator’s 1µs family response time when defining fault-detection timing.
Recommandé
Battery Voltage Window Monitor
A dual LM2903PWR configuration is well suited to battery-pack window monitoring, where one channel can detect an upper limit and the other can detect a lower limit. The LM2903 family is associated with a ±18V, or 36V total, operating range, while the improved B-family information lists a maximum rating of up to 38V. Rail-to-rail input behavior helps the channels evaluate signals near supply-rail conditions, and the 200µA-per-comparator supply-current figure supports low-power monitoring. External pull-up resistors define the logic-high output voltage, allowing the open-collector fault signals to connect to a host controller. Resistor-divider tolerances and input offset voltage should be included in the threshold-error budget.
Recommandé
Sensor Signal Conditioning
The LM2903PWR can convert a slowly changing sensor signal into a sharp digital event by comparing the sensor against a locally generated reference. The rail-to-rail input characteristic is useful for sensors whose operating range approaches a supply rail, while the 0.37mV maximum offset and 3.5nA maximum bias-current figures from the improved LM2903B family reduce sensitivity to reference-network error. Each open-collector output can sink current directly or drive an external pull-up. The dual configuration supports two independently scaled sensor channels or a hysteresis window. Place the divider and reference components near the relevant input pins to minimize parasitic pickup and keep the sensor return path separated from high-current switching returns.
Recommandé
Control System Limit Detector
The LM2903PWR provides two independent decision channels for industrial control boards that must enforce operating limits or enable a machine only within a valid range. One comparator can detect an upper control-point crossing while the second handles the lower crossing, allowing a wired logic implementation with open-collector outputs. The family’s 1µs response time supports relatively prompt transitions, and the associated LM2903B specifications list 2kV HBM ESD protection and a maximum rating of up to 38V. The TSSOP package keeps the two channels close together on a compact control PCB. Designers should validate the pull-up voltage against the driven logic and account for simultaneous output transitions when defining fault-response behavior.
Recommandé
Automotive-Level Logic Interface
The dual open-collector architecture of the LM2903PWR is useful for interfacing a 12V-class electrical system to low-voltage digital logic. Two channels can monitor separate vehicle electrical conditions, while pull-up resistors connect the outputs to the logic rail required by the receiving device. The verified product information identifies the associated improved LM2903B family as a 2kV HBM ESD-rated device with maximum ratings up to 38V. A qualified production design should select the exact ordering option and temperature grade required by its automotive specification rather than assuming that every LM2903PWR ordering designation has the same qualification status. The TSSOP layout also supports compact electronic control-unit construction.
Recommandé
Analog-to-Digital Conversion Front End
The LM2903PWR can serve as a fast threshold element ahead of an ADC or digital control input when an analog signal needs to be converted into an immediate event. Its differential inputs support comparison against a local reference, while the open-collector output can be pulled up to the receiving logic rail. The 1µs family response time helps minimize the interval between crossing the threshold and generating the digital indication. Two channels can handle separate thresholds, such as a warning and shutdown event, without requiring two packages. Keep the comparator input traces short, provide a low-noise reference, and avoid routing them near switching power stages. The input common-mode range and supply limits must be checked against the analog signal and transient environment.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM2903PWR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM2903PWRG4 | LM2903PWR |
|---|---|---|---|
| Package | 8-TSSOP | 8-TSSOP | 8-TSSOP |
| Brand | Texas Instruments | Texas Instruments | ROHM Semiconductor |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Output Type | Open-collector | Open-collector | Open-collector |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail |
Principaux différenciateurs
- Two independent comparator channels in one compact package (vs LM2901PW)
- Wide supply capability for industrial threshold detection (vs LM2903PWRG4)
- Low-offset dual-channel sensing (vs LM2903PWR)
Notes de conception
Keep the two differential input nets short and place their reference-divider components close to the relevant input pins. Route the pair together to minimize differential pickup from switching nodes and keep the comparator ground return continuous beneath the device. Because threshold accuracy depends on the difference between two input voltages, unequal input routing or a noisy shared ground can create errors larger than the specified 0.37mV offset in the improved LM2903B family.
Attach a suitable bypass capacitor from each device supply connection to the appropriate ground reference and place it immediately beside the package. Keep the pull-up return current separate from sensitive input-return paths where practical. The associated family specifies 200µA supply current per comparator, but total supply demand also includes input currents, pull-up load current, leakage, and output-transition effects.
Do not treat the open-collector output as a push-pull logic output. It can sink current when active but requires an external pull-up resistor to establish a high voltage. Confirm that the pull-up rail is compatible with every connected load, and do not exceed the device-family supply and absolute-maximum ratings. Verify the exact ordering option because the same LM2903PWR code is associated with more than one manufacturer.
Informations de conformité
The verified distributor search identifies LM2903PWR as RoHS Compliant. Automotive qualification and other compliance attributes were not established for the exact ordering option.