LM2904M-FS - Dual 26V Op Amp 500V/ms | onsemi
Référence : LM2904M-FS ✓ ActifLM2904M-FS Présentation
An operational amplifier is an analog signal-conditioning IC that compares an inverting input with a non-inverting input and amplifies the voltage difference between them. The dual-amplifier configuration places two independent amplifiers in one package, making the LM2904M-FS suitable for signal conditioning, feedback-control loops, sensor amplification, and general analog signal paths. Within the product hierarchy, it is a dual operational amplifier within the amplifier-IC and analog-semiconductor categories.
The LM2904M-FS combines a 26 V maximum supply capability from the LM2904 family with low input-bias current and a 500 V/ms slew rate. Its internally compensated architecture removes the need for an external frequency-compensation network in common closed-loop applications. The two independent channels can operate in non-inverting, inverting, voltage-follower, comparator-style, and feedback configurations, provided the design respects the device's common-mode and output-voltage limits.
The 8-SOIC footprint provides a conventional surface-mount assembly format with exposed leads on both package sides. Each half of the amplifier uses four pins: two inputs, one output, and the power connection. The standard SOIC-8 pin arrangement simplifies PCB layout, but normal single-supply operation requires bypassing the positive supply pin to ground and accounting for the input and output common-mode limitations near the supply rails.
Typical applications include low-frequency industrial instrumentation, buffered sensor interfaces, audio preamplifier stages, analog monitoring, and general-purpose dual-amplifier signal conditioning. The LM2904M-FS is particularly useful where two related analog channels are required on one board, such as an input stage and feedback amplifier in a control circuit. For high-speed or very low-offset instrumentation, a precision amplifier family may be preferable.
Decouple the power supply with a short, low-inductance path from the positive supply pin to ground, and route the amplifier output away from high-current switching nodes. Avoid using the device outside its input common-mode range, especially in single-supply circuits where the input approaches ground. Stable feedback-network layout and adequate output-load capability should be verified for every analog channel.
This product page combines the exact LM2904M-FS ordering information with family-level electrical characteristics, a complete SOIC-8 pin map, practical application guidance, and a qualified drop-in comparison. It is designed to help engineers identify the correct footprint, understand the device's analog signal-conditioning role, and select among documented alternatives without changing the PCB land pattern.
Alternatives de remplacement direct pour LM2904M-FS — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM2904M-FS (même facteur de forme et même empreinte) — différant par Package, Amplifier Type, Input Offset Voltage, Number of Channels, Slew Rate.
LM2904M/NOPB
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2904D
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2904BIDR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2904BA
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LM2904M-FS Valeurs maximales et caractéristiques électriques
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 circuits |
| Tension d'alimentation | Up to 26 V |
| Supply Configuration | Single supply |
| Input Bias Current | 250 nA |
| Slew Rate | 500 V/ms |
| Input Offset Voltage | 2 mV |
| Gain-Bandwidth Product | 700 kHz |
| Compensation | Internally frequency compensated |
| Boîtier | 8-pin SOIC |
| Type de montage | Surface mount |
| Channel Count | 2 |
| Statut RoHS | Compliant |
| Slew Rate | 500 V/ms |
Configuration des broches de LM2904M-FS
| Broche 1 | OUT1 — Output of amplifier channel 1 |
| Broche 2 | -IN1 — Inverting input of amplifier channel 1 |
| Broche 3 | +IN1 — Non-inverting input of amplifier channel 1 |
| Broche 4 | V- — Negative power supply or ground connection |
| Broche 5 | +IN2 — Non-inverting input of amplifier channel 2 |
| Broche 6 | -IN2 — Inverting input of amplifier channel 2 |
| Broche 7 | OUT2 — Output of amplifier channel 2 |
| Broche 8 | V+ — Positive power supply connection |
Applications typiques
LM2904M-FS convient pour 6 applications: Industrial Sensor Signal Conditioning, Audio Preamplifier and Buffer, Power Supply Feedback Control, Analog Monitoring and Instrumentation, IoT Sensor Interface, Automotive and Vehicle Electronics.
Industrial Sensor Signal Conditioning
The onsemi LM2904M-FS fits a dual-channel industrial sensor front end because each internally compensated amplifier can provide gain, inversion, filtering, or buffering for a low-frequency transducer signal. Its listed 250 nA input-bias current is useful when the source impedance is high enough that amplifier bias current could distort the measurement, while the 500 V/ms slew rate supports signals beyond very low audio frequencies. Place the sensing channel and a feedback or reference amplifier on the two independent sections. The principal design constraint is the input common-mode range: single-supply operation is convenient for 5 V systems, but the sensor output must remain inside the range stated by the onsemi LM2904 family datasheet. Decouple the supply pin locally and avoid routing the sensor input beside switching-node traces.
Recommandé
Audio Preamplifier and Buffer
The LM2904M-FS can provide the first gain stage and an output buffer in a low-frequency audio preamplifier because the SOIC-8 package contains two independent amplifiers. The 500 V/ms slew rate is adequate for many audio-band signals, and the approximately 2 mV offset in the listed configuration can affect the quiescent output level in a single-supply circuit. Use one channel for gain and the other for buffering or active filtering, with the feedback resistors selected for the intended impedance and bandwidth. Avoid using the device where its input offset and bias characteristics exceed the system noise or headroom budget. Keep the ground return of the audio path away from motor, relay, and switching-converter currents.
Recommandé
Power Supply Feedback Control
The two channels in the onsemi LM2904M-FS can implement error amplification and output buffering in a basic analog control or regulated-supply feedback path. The internal frequency compensation simplifies the stable closed-loop design, and the 26 V LM2904 family supply capability supports higher-voltage control circuitry. One amplifier may compare the feedback node with a reference, while the other drives or buffers the controlled node. The design must account for the amplifier's output swing, input common-mode limits, and the phase margin created by the complete feedback network. Keep the high-current power stage electrically separated from the feedback trace, and place the supply bypass capacitor directly across the positive and ground pins.
Recommandé
Analog Monitoring and Instrumentation
The LM2904M-FS is appropriate for low-frequency monitoring modules that amplify a conditioned sensor or measurement signal and provide a second channel for reference, filter, or differential-output functions. The 250 nA input-bias current helps minimize loading when the monitored circuit presents a high source impedance, and the 500 V/ms slew rate avoids severe slew distortion on moderate-bandwidth waveforms. In a single-supply instrument, bias the signal into the valid common-mode region and evaluate whether the approximately 2 mV offset is acceptable at the required gain. Use short, guarded feedback paths and connect the two amplifier grounds to the same quiet analog return. Verify noise and accuracy against the measurement bandwidth rather than selecting the device from slew rate alone.
Recommandé
IoT Sensor Interface
The LM2904M-FS can condition a sensor output before an ADC or embedded controller in an IoT node because its dual channels support both amplification and filtering. A 250 nA input-bias current is valuable for high-impedance sensors, while the internal compensation allows closed-loop operation without a separate compensation capacitor. One section can amplify the sensor signal and the other can form an active low-pass filter, although both sections share the same supply limitations. The single-supply architecture fits 3.3 V or 5 V systems, provided the signal stays within the input common-mode range. Place the IC near the sensor input, keep the analog trace short, and separate the supply bypass return from digital and wireless switching currents.
Recommandé
Automotive and Vehicle Electronics
The LM2904M-FS can be evaluated for low-frequency vehicle electronics such as actuator feedback, sensor conditioning, and simple control loops. Its dual SOIC-8 implementation reduces component count when two independent analog functions are required, and the LM2904 family's 26 V supply capability covers many 12 V vehicle rails when suitable transient and operating requirements are met. Automotive use requires additional review of temperature range, qualification, ESD behavior, load dump exposure, and production status because the base LM2904M-FS listing does not by itself establish AEC-Q100 qualification. Use a qualified automotive amplifier if the vehicle program mandates it, and protect every external pin against the vehicle's electrical environment.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM2904M-FS — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM2904M/NOPB | LM2904D | LM2904B | LM2904BA |
|---|---|---|---|---|---|
| Manufacturer | onsemi | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Amplifier Channels | 2 | 2 | 2 | 2 | 2 |
| Product Family | LM2904 | LM2904 | LM2904 | LM2904B | LM2904BA |
| Compensation | Internal | Internal | Internal | Internal | Internal |
| Supply Configuration | Single supply | Single supply | Single supply | Single supply | Single supply |
Principaux différenciateurs
- Uses the exact onsemi LM2904M-FS order configuration (vs LM2904M/NOPB)
- Documented 250 nA input-bias current (vs LM2904B)
- Documented 500 V/ms slew rate (vs LM2904BA)
- Explicit approximately 2 mV offset specification (vs LM2904D)
Notes de conception
Place the supply bypass capacitor directly between pin 8 (V+) and pin 4 (V-) with a short, low-inductance return path. Connect the two amplifier channels to the same quiet analog ground when they process related signals. Route feedback resistors close to their associated input pins, and avoid placing the analog input traces parallel to switching-node or high-current output paths because capacitive coupling can degrade the 250 nA-class input behavior.
Check the input common-mode range and output swing before selecting single-supply operating points. A 5 V supply does not make every 0 V input usable at every gain, and the output also has headroom restrictions. The LM2904M-FS is internally compensated, but stable operation still depends on the selected closed-loop gain, source impedance, capacitive load, feedback values, and power-supply bypassing. Use the manufacturer's application and stability guidance when driving unusual loads.
For low-frequency sensor interfaces, keep the high-impedance input node physically small and guard it against moisture and surface leakage. The listed 250 nA input-bias current becomes less significant as source impedance decreases, while the approximately 2 mV offset can become more visible after high gain. Evaluate the complete gain chain, including sensor tolerance, reference accuracy, resistor errors, and amplifier offset, rather than relying on slew rate alone.
Informations de conformité
The LM2904M-FS product listing identifies the device as RoHS compliant. No separate REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was found in the cited product information.