LM2904VQDRG4 - Dual 30V 700kHz Op Amp | Texas Instruments
Référence : LM2904VQDRG4 ✓ ActifLM2904VQDRG4 Présentation
An operational amplifier, or op amp, is a high-gain differential amplifier whose external feedback network determines its closed-loop behavior. A dual op amp combines two amplifiers in one package, reducing board area when a circuit needs two related analog functions. Within the broader semiconductor hierarchy, an op amp is an analog integrated circuit used for linear amplification, filtering, comparison, and feedback control.
The LM2904VQDRG4 is intended for general-purpose applications rather than precision or high-speed signal chains. Its 700 kHz gain-bandwidth product is suitable for low-to-moderate bandwidth amplification, while the 30 V supply rating allows operation from single or dual supplies. A 500 µA per-channel quiescent current helps limit power consumption in battery-operated and low-power equipment. The broad -40°C to 125°C operating range supports industrial and automotive environments.
Each channel can be configured as an inverting amplifier, non-inverting amplifier, voltage follower, comparator, or active-filter building block. Common-mode and output-drive behavior must be checked against the specific operating point because the LM2904V trades precision and bandwidth for wide supply-voltage tolerance and low quiescent current. The dual configuration is particularly useful when a board requires gain in one signal path and buffering or active filtering in another.
Typical uses include transducer-signal conditioning, 4-20 mA current-loop receivers, low-side current sensing, sensor amplification, power-supply feedback, audio preamplification, and industrial control loops. The device is also suitable for battery-powered instrumentation because its low quiescent current reduces the supply burden when both channels are not continuously active.
Design layouts should keep input and feedback traces short, place input-biasing resistors close to the amplifier pins, and avoid routing high-current switching paths beneath the SOIC footprint. Decoupling capacitors should be connected with minimal loop area, and unused amplifier channels should be configured according to the Texas Instruments datasheet rather than left open. Verify input and output swing, common-mode range, output-current capability, and stability for every selected feedback network.
This product page combines the Texas Instruments family specifications, exact MPN packaging details, lifecycle-oriented sourcing guidance, and application-focused design guidance. It also highlights the need to distinguish verified drop-in alternatives from electrically similar devices that require different packages or different pin assignments.
Alternatives de remplacement direct pour LM2904VQDRG4 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM2904VQDRG4 (même facteur de forme et même empreinte) — différant par Package, Operating Temperature Range, Automotive Qualification, Input Offset Voltage, Slew Rate.
LM2904VQDRG4Q1
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2904BIDR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2904BA
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
CA0158AE
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LM2904VQDRG4 Valeurs maximales et caractéristiques électriques
| Product Type | Dual operational amplifier |
| Number of Amplifier Channels | 2 channels |
| Maximum Supply Voltage | 30 V |
| Single-Supply Operating Range | 3 V to 30 V |
| Dual-Supply Operating Range | ±4.5 V to ±15 V |
| Gain-Bandwidth Product | 700 kHz |
| Courant de repos | 500 µA per channel |
| Plage de température de fonctionnement | -40°C to 125°C |
| Boîtier | 8-pin SOIC (D) |
| Nombre de broches | 8 pins |
| Type de montage | Surface mount |
| Amplifier Classification | General-purpose operational amplifier |
| Automotive Qualification | Qualified variant available as LM2904VQDRG4Q1 |
Configuration des broches de LM2904VQDRG4
| Broche 1 | OUTA — Amplifier A output |
| Broche 2 | IN A- — Amplifier A inverting input |
| Broche 3 | IN A+ — Amplifier A non-inverting input |
| Broche 4 | V- — Negative supply connection |
| Broche 5 | IN B+ — Amplifier B non-inverting input |
| Broche 6 | IN B- — Amplifier B inverting input |
| Broche 7 | OUTB — Amplifier B output |
| Broche 8 | V+ — Positive supply connection |
Applications typiques
LM2904VQDRG4 convient pour 6 applications: Industrial Sensor Signal Conditioning, Low-Side Current Sensing, Battery-Powered Instrumentation, Audio Preamplification, Active Filtering and Control Loops, Automotive and Heavy Equipment Control.
Industrial Sensor Signal Conditioning
The LM2904VQDRG4 is well suited to amplifying weak sensor signals in industrial control equipment because its two channels can handle related gain and filtering functions in one 8-pin SOIC package. The 700 kHz gain-bandwidth product supports low-to-moderate bandwidth signals, while the 30 V maximum supply rating accommodates industrial rails more readily than many low-voltage precision amplifiers. The 500 µA per-channel quiescent current also limits power demand in distributed sensing systems. During design, verify the input common-mode range against the sensor output and confirm output swing at the selected gain before committing the circuit.
Recommandé
Low-Side Current Sensing
The LM2904VQDRG4 can amplify the voltage produced by a low-value shunt resistor when the common-mode voltage remains within the amplifier's permitted input range. Its 700 kHz gain-bandwidth product is adequate for many current-monitoring loops, and the dual package permits a second channel to support gain, filtering, or offset correction. The wide 3 V to 30 V single-supply range supports control systems operating from higher-voltage rails. Accurate current measurement depends on checking offset voltage, bias current, common-mode limits, and shunt-induced output swing in the final operating point.
Recommandé
Battery-Powered Instrumentation
The LM2904VQDRG4 fits portable measurement and monitoring equipment that needs two general-purpose analog channels without the power demand of a high-speed precision amplifier. Its approximately 500 µA quiescent current per channel is valuable when the amplifier must remain connected to a battery, while the 3 V minimum single-supply voltage supports low-energy designs. The -40°C to 125°C specification provides broad environmental coverage. Designers should still evaluate input bias current, noise, and leakage against the sensor source impedance because low quiescent current alone does not establish metrological accuracy.
Recommandé
Audio Preamplification
The LM2904VQDRG4 can provide the first gain stage in a low-frequency audio preamplifier or active tone-control circuit. Its 700 kHz gain-bandwidth product covers the audio band, and the dual package allows one channel to amplify while the other implements a buffer, filter, or complementary gain path. The broad supply-voltage range is useful in legacy and industrial equipment operating from elevated rails. Because the LM2904V is a general-purpose amplifier rather than a low-noise audio part, designers should evaluate input voltage noise, distortion at the required signal level, output swing, and stability with the selected feedback network.
Recommandé
Active Filtering and Control Loops
The two amplifiers in the LM2904VQDRG4 can implement independent active-filter or feedback-control sections when the required bandwidth remains well below the 700 kHz gain-bandwidth product. A dual package reduces footprint and component count in analog control boards, while operation from -40°C to 125°C supports equipment exposed to wide environmental variation. Stability depends on noise gain, source impedance, load capacitance, and component tolerances, so the manufacturer-recommended compensation methods should be used. Check output drive against the feedback network because a wide voltage rating does not guarantee equal drive capability into every load.
Recommandé
Automotive and Heavy Equipment Control
For automotive or heavy-equipment applications requiring a qualified device, the LM2904VQDRG4Q1 provides the same 8-pin SOIC architecture and dual 30 V, 700 kHz operational-amplifier characteristics highlighted for LM2904VQDRG4. The -40°C to 125°C operating range suits demanding equipment environments, while two channels can support actuator feedback, sensor conditioning, or buffered references. Qualification alone does not guarantee suitability for every functional safety or environmental requirement; the complete manufacturer quality document, schematic review, grounding strategy, and transient analysis remain necessary for production designs.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM2904VQDRG4 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM2904VQDRG4Q1 | LM2904B | LM2904BA | CA0158AE |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics |
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Amplifier Configuration | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
Principaux différenciateurs
- Direct automotive-qualified option (vs LM2904VQDRG4Q1)
- Broad supply-voltage capability in a dual package (vs CA0158AE)
- Low quiescent demand with two independent channels (vs LM2904B)
Notes de conception
Route each inverting-input and feedback connection directly to the relevant SOIC pin without intervening test pads or long branches. Keep resistor networks close to pins 2 and 6, and keep output routing away from the input and supply pins. This reduces parasitic feedback and helps preserve the stability margin expected from the 700 kHz gain-bandwidth device.
Place the supply bypass capacitor immediately between pins 4 and 8 with a short, low-inductance return path. If the circuit uses split positive and negative rails, decouple each rail independently according to the manufacturer layout guidance. Confirm that the maximum total supply voltage remains at or below 30 V, including startup overshoot, because transient overshoot can damage a device even when its nominal operating point is valid.
Do not assume that a 30 V supply rating makes every input and output valid at 30 V. Check the input common-mode range and output swing across temperature and load. Likewise, verify offset voltage and input bias current when the source impedance is high, since a general-purpose amplifier can amplify those errors even when its 500 µA per-channel quiescent current is suitable for the power budget.
Use short ground returns and avoid placing sensitive input traces beneath the package where they can couple to output or supply currents. For high-gain configurations, keep both input terminals at similar impedance to minimize offset caused by bias-current imbalance. If the source is capacitive, add the isolation resistance recommended by the manufacturer to prevent oscillation near the 700 kHz gain-bandwidth limit.
Informations de conformité
The standard LM2904VQDRG4 is identified as a general-purpose grade, while the separate LM2904VQDRG4Q1 orderable variant is automotive qualified. Compliance attributes beyond that distinction require confirmation from the manufacturer product documentation.