LM324ADTB - Quad 3-32V General-Purpose Op Amp | onsemi
Référence : LM324ADTB ✓ ActifLM324ADTB Présentation
An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the voltage difference between its two inputs. The LM324 belongs to the quad operational amplifier hierarchy: operational amplifier, voltage-feedback amplifier, analog signal-conditioning IC, and power-management IC. Its four independent channels can perform amplification, buffering, summing, comparison, and basic active-filter functions without requiring four separate packages.
The LM324ADTB supports single-supply operation from 3 V to 32 V, making it suitable for systems whose rails are higher than those of common rail-to-rail precision amplifiers. Its 3 mV input offset voltage supports general-purpose applications where input accuracy requirements are moderate. True differential inputs allow each channel to respond to the difference between its inverting and non-inverting signals. The integrated quad configuration also reduces board area and simplifies multi-channel routing.
As a general-purpose amplifier, the LM324 series emphasizes practical utility rather than high speed or precision. The manufacturer describes the devices as low-cost quad operational amplifiers that are especially useful in single-supply systems. Their quiescent current is approximately one-fifth that of conventional dual operational amplifiers, according to the manufacturer datasheet. Detailed gain-bandwidth, slew-rate, input-bias-current, and common-mode limits must be checked against the operating conditions before precision filtering or signal-chain use.
Typical applications include four-channel sensor conditioning, transducer buffering, audio preamplification, current-voltage conversion, DC signal amplification, and mixed-signal instrumentation. The 14-pin TSSOP package is useful for compact industrial, consumer, and communications equipment where four analog functions must be accommodated without using four separate amplifier packages. Supply bypassing and stable feedback layouts remain important at the board level.
For a new design, place the device close to the powered circuits it serves and connect a suitable bypass capacitor near the supply pins. Keep feedback resistors and input traces short, maintain symmetrical routing where practical, and account for input bias-current errors when using high source impedances. The single supply must remain within the 3 V to 32 V operating range under all tolerance, transient, and temperature conditions.
This page consolidates the LM324ADTB electrical ratings, package details, pin assignments, replacement options, and practical layout considerations into an engineering-focused reference. It also identifies where the general-purpose LM324 architecture is appropriate and where precision, speed, rail-to-rail operation, or a lower-offset amplifier would provide a better design choice.
Alternatives de remplacement direct pour LM324ADTB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM324ADTB (même facteur de forme et même empreinte) — différant par Package, Amplifier Type, Input Offset Voltage, Gain-Bandwidth Product, Number of Channels.
LM324DTB
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM324APWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM324KAPW
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM324DT
✅ Remplacement direct✗ Rupture de stock
$0.0827 / unité
Voir la fiche technique →LM324APWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM324ADTB Valeurs maximales et caractéristiques électriques
| Number of Amplifier Channels | 4 channels |
| Supply Voltage Range | 3 V to 32 V |
| Input Offset Voltage | 3 mV |
| Input Type | True differential inputs |
| Product Classification | Standard general-purpose amplifier |
| Architecture | Quad voltage-feedback operational amplifier |
| Boîtier | 14-pin TSSOP |
| Type de montage | Surface mount |
Configuration des broches de LM324ADTB
| Broche 1 | OUT1 — Amplifier 1 output |
| Broche 2 | IN1- — Amplifier 1 inverting input |
| Broche 3 | IN1+ — Amplifier 1 non-inverting input |
| Broche 4 | V+ — Positive supply voltage |
| Broche 5 | IN2+ — Amplifier 2 non-inverting input |
| Broche 6 | IN2- — Amplifier 2 inverting input |
| Broche 7 | OUT2 — Amplifier 2 output |
| Broche 8 | OUT3 — Amplifier 3 output |
| Broche 9 | IN3- — Amplifier 3 inverting input |
| Broche 10 | IN3+ — Amplifier 3 non-inverting input |
| Broche 11 | V- — Negative supply or ground connection |
| Broche 12 | IN4+ — Amplifier 4 non-inverting input |
| Broche 13 | IN4- — Amplifier 4 inverting input |
| Broche 14 | OUT4 — Amplifier 4 output |
Applications typiques
LM324ADTB convient pour 6 applications: Industrial Sensor Conditioning, Audio Preamplification, Current-to-Voltage Conversion, Active Filtering, Data Acquisition Front End, Automotive Control Module.
Industrial Sensor Conditioning
The LM324ADTB fits four-channel industrial sensor conditioning because it combines four true-differential amplifiers in one 14-pin TSSOP package and operates from 3 V to 32 V. One channel can buffer a pressure or temperature transducer, another can amplify a bridge or differential sensor output, and the remaining channels can support excitation, gain, or active filtering. The 3 mV input offset specification is practical for general-purpose measurements, although high-impedance sensors require an input-bias-current check. Keep sensor traces short, provide local supply bypassing, and confirm common-mode limits at the lowest operating supply voltage.
Recommandé
Audio Preamplification
The LM324ADTB can provide multiple low-cost audio preamplifier or buffering channels when the design does not require rail-to-rail swing, low noise, or high bandwidth. Its four independent channels reduce package count in mixer, monitor, consumer, and communication equipment, while operation from a single 3 V to 32 V rail simplifies power architecture. The 3 mV input offset is generally acceptable for line-level signal paths, but microphone and low-level designs should verify input bias current, noise, and output swing against the selected supply voltage.
Recommandé
Current-to-Voltage Conversion
The LM324ADTB is useful in current-to-voltage converter and transimpedance stages because each channel can combine a feedback resistor with a second amplifier to create a virtual ground or active current sink. The device’s true differential inputs support sensing around a biased output, and the 14-pin TSSOP permits four amplifier functions in a compact footprint. Confirm the input bias current against the source impedance, keep feedback loops compact, and check output-current limits because the converter’s accuracy and settling behavior depend on stable feedback components.
Recommandé
Active Filtering
The LM324ADTB can implement first-order and basic higher-order active filters because four channels are available in one package and the amplifier supports 3 V to 32 V operation. A practical board can allocate channels to low-pass and high-pass sections, a summing stage, and an output buffer. Resistor matching and the amplifier’s gain-bandwidth and slew behavior determine usable frequency range. Keep the passive components and feedback paths compact, observe the 3 mV offset contribution, and test the complete filter rather than relying only on ideal transfer equations.
Recommandé
Data Acquisition Front End
The LM324ADTB provides four channels for multiplexing, buffering, level shifting, and gain stages around a data-acquisition front end. True differential inputs allow each amplifier to process the difference between two sensor or converter outputs, reducing common-mode disturbance during analog signal conditioning. The 3 V to 32 V supply range supports both low-voltage and higher-voltage systems, but input bias current, common-mode range, output swing, and settling characteristics must be checked against the converter and sensor. Place the amplifier near the source and bypass the supply locally.
Recommandé
Automotive Control Module
The LM324ADTB is appropriate for general-purpose analog conditioning inside an automotive electronic control module when its automotive ordering code and qualification requirements satisfy the program specification. The quad arrangement supports sensor buffers, actuator-driver feedback paths, threshold amplifiers, and auxiliary filters within a single 14-pin TSSOP. Its 3 V to 32 V supply range covers many vehicle electrical systems, but designers must still verify transient protection, temperature grade, electromagnetic compatibility, and production traceability. Use stable reference components and follow the manufacturer’s decoupling and layout guidance.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM324ADTB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM324DTB | LM324APWR | LM324KAPW | LM324DT | LM324APW |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | Texas Instruments | Texas Instruments | STMicroelectronics | Texas Instruments |
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Product Classification | Standard general-purpose amplifier | General-purpose quad operational amplifier | General-purpose quad operational amplifier | General-purpose quad operational amplifier | General-purpose quad operational amplifier | General-purpose quad operational amplifier |
Principaux différenciateurs
- Combines four general-purpose amplifiers with a wide supply range (vs LM2902DTB)
- Uses a compact 14-pin TSSOP for four-channel analog conditioning (vs LM324ADBR)
- Automotive-oriented onsemi ordering option (vs LM324APWR)
Notes de conception
Route the positive supply directly to pin 4 and ground to pin 11 using short, low-impedance traces. Place the manufacturer-recommended bypass capacitor adjacent to the supply pins so switching and input-stage noise are attenuated before they reach the amplifier. Because the LM324ADTB operates from 3 V to 32 V, verify that supply transients remain below the maximum operating voltage and that ground offsets do not move input or output signals outside their valid ranges.
Place the TSSOP close to the sources of its four channels and keep input, feedback, and reference paths compact. Long traces can pick up noise, create parasitic capacitance, and add phase delay that reduces stability margin. Avoid routing high-current return paths or fast-switching nodes beside amplifier inputs. If a channel processes a high-impedance sensor, use a guarded or driven-shield approach only after confirming the input bias-current implications.
Do not treat the 3 mV input offset specification as a complete accuracy budget. In amplifier configurations, the effective output error can also include input bias current multiplied by source and feedback impedances, resistor tolerance, gain error, and temperature drift. For instrumentation or active filters, calculate each contribution and compare it with the required error before substituting another LM324-family device.
Use short, direct feedback loops and avoid capacitance on high-impedance non-inverting inputs unless the application requires intentional filtering. If the source impedance is high, include input-bias-current error and capacitive pickup in the noise analysis. When the circuit operates at high frequency, verify the amplifier’s gain-bandwidth and slew-rate limits from the manufacturer datasheet instead of assuming that the 3 V to 32 V supply rating defines high-speed performance.
Informations de conformité
The automotive-oriented ordering suffix does not by itself establish AEC-Q100 qualification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer’s current declaration or product documentation.