LM324APWRG4 - Quad General-Purpose Op Amp, 14-TSSOP | Texas Instruments
Référence : LM324APWRG4 ✓ ActifLM324APWRG4 Présentation
An operational amplifier is a high-gain, differential-input, single-ended-output active device that drives its output toward the higher of its two inputs. The LM324 belongs to the quad general-purpose op-amp family, a direct descendant of the classic single LM741 architecture in which four amplifiers share one package. In the signal-chain hierarchy it sits between discrete transistor stages and precision instrumentation amplifiers: it is a voltage-feedback, internally compensated (unity-gain stable) amplifier aimed at cost-sensitive, high-volume analog signal conditioning.
Key differentiators of the LM324A grade are the tighter ±3 mV typical input offset voltage and the enhanced ESD robustness compared with earlier LM324 revisions. Because each amplifier is internally compensated, it behaves correctly at unity gain without external frequency-compensation networks, and the common-mode input range includes ground so the device can be used in single-supply sensing circuits whose signal swings to 0 V.
The A suffix denotes the improved-offset version, while the PWRG4 suffix denotes the 14-pin TSSOP, tape-and-reel, RoHS-green (lead-free) ordering code. Because the package is only 14 pins across and 0.8 mm pitch, four amplifiers fit into a footprint comparable to a single SOIC-14, which keeps quad-buffer, quad-instrumentation and multi-channel sensor-conditioning boards compact.
Typical applications include sensor signal conditioning, low-side current monitoring, DC motor and actuator driver stages, audio mixer sub-circuits, temperature-controller error amplifiers, and general instrumentation buffers. Four matched channels in one package also reduce board area, ground-bounce risk, and part-count on multi-channel analog boards.
When designing with the LM324APWRG4, remember that it is not a rail-to-rail input or output amplifier: the common-mode and output swing limits are set by the supply rails, so headroom of a few hundred millivolts must be reserved at the output. Decouple each supply pin locally, keep feedback loops short, and prefer the LM324A offset grade over the base LM324 when accuracy matters.
Alternatives de remplacement direct pour LM324APWRG4 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM324APWRG4 (même facteur de forme et même empreinte) — différant par Package, Amplifier Type, Supply Configuration, Input Offset Voltage, Number of Amplifiers.
LM324APWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM324PWRG4
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM324PWRE4
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM324KPWR
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →LM324APWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM324APWRG4 Valeurs maximales et caractéristiques électriques
| Number of Amplifiers | 4 |
| Amplifier Type | Quad general-purpose operational amplifier, unity-gain stable |
| Supply Voltage Range (Total) | ±16 V (32 V max total supply) |
| Input Offset Voltage | ±3 mV typ (LM324A grade) |
| Supply Current per Amplifier | 0.8 mA typ, independent of supply voltage |
| ESD Protection | 2 kV |
| Common-Mode Input Range | Includes ground, allowing direct sensing at 0 V |
| Nombre de broches | 14 |
| Boîtier | 14-pin TSSOP (PW), 0.8 mm pitch |
| Type de montage | Surface Mount |
| Shipping Format | Tape and Reel |
| Green / Lead-Free Status | RoHS-compliant green (G4 suffix) |
| Statut RoHS | Compliant |
| REACH Status | Compliant |
| AEC-Q100 Qualification | Not qualified (industrial/commercial general-purpose grade) |
Configuration des broches de LM324APWRG4
| Broche 1 | OUT1 — Amplifier 1 output |
| Broche 2 | IN1- — Amplifier 1 inverting input |
| Broche 3 | IN1+ — Amplifier 1 non-inverting input |
| Broche 4 | V+ — Positive supply voltage |
| Broche 5 | IN2+ — Amplifier 2 non-inverting input |
| Broche 6 | IN2- — Amplifier 2 inverting input |
| Broche 7 | OUT2 — Amplifier 2 output |
| Broche 8 | OUT3 — Amplifier 3 output |
| Broche 9 | IN3- — Amplifier 3 inverting input |
| Broche 10 | IN3+ — Amplifier 3 non-inverting input |
| Broche 11 | V- — Negative supply voltage (or ground in single-supply use) |
| Broche 12 | IN4+ — Amplifier 4 non-inverting input |
| Broche 13 | IN4- — Amplifier 4 inverting input |
| Broche 14 | OUT4 — Amplifier 4 output |
Applications typiques
LM324APWRG4 convient pour 6 applications: Sensor Signal Conditioning, DC Motor and Actuator Driver Stages, Low-Side Current Monitoring, Industrial Audio and Mixer Sub-Circuits, Temperature Control and Thermostat Loops, General Instrumentation and Test Equipment.
Sensor Signal Conditioning
The LM324APWRG4 fits front-end conditioning for resistive, thermocouple and bridge sensors where a 0-5 V or 0-3.3 V sensor output must be scaled into a level the ADC can measure. Its common-mode input range includes ground, so millivolt-level signals riding on a 0 V reference are sensed directly without a mid-supply bias, and the 3 mV typical offset of the A grade sets the smallest signal the stage can resolve accurately. Four channels in one 14-pin TSSOP let a single board host the sensor amp, a reference buffer, an anti-alias filter and a housekeeping channel. Feedback resistors are kept to 0.1 percent for ratio accuracy, and supply decoupling is placed within a few millimetres of pins 4 and 11.
Recommandé
DC Motor and Actuator Driver Stages
In brushed DC motor and solenoid driver designs, the LM324APWRG4 supplies the error amplifier and transconductance stages that close the current-control loop around an H-bridge or discrete power stage. The quad package provides one amplifier for the current-sense reference, one for the sense-signal amplifier, one as the error amplifier and one for optional speed or position conditioning, reducing board area on space-constrained control boards. Because the output swing is limited by the supply rails and the part is not rail-to-rail, design with at least 1 V of headroom at 5 V or 12 V so the error amplifier can drive its full command range without clipping.
Recommandé
Low-Side Current Monitoring
The LM324APWRG4 is a standard choice for amplifying the millivolt output of a low-side shunt in battery, charger and power-supply designs. The shunt signal is referenced to ground, which falls inside the amplifier's common-mode range including ground, so no artificial bias is needed at the input, and the wide supply range allows the sense stage to sit anywhere from a 5 V auxiliary rail up to a 36 V bus. With the A grade's 3 mV typical offset, the practical shunt resolution is set by the shunt element rather than the amplifier. A 100 ohm gain network with a 1 percent ratio keeps gain error low, and input lead routing should be differential and away from switching nodes.
Recommandé
Industrial Audio and Mixer Sub-Circuits
For entry-level mixer, intercom and instrument-amplifier input stages, the LM324APWRG4 provides four amplifier channels that handle microphone pre-amplification, summing and output buffering in a single 14-pin TSSOP footprint. This consolidation shortens ground paths between stages and reduces the component count on analog audio boards, while the 0.8 mA typ quiescent current per amplifier keeps thermal and battery impact low. The device is not a low-noise part, so it suits general-purpose signal paths rather than high-fidelity audio fronts, and the output swing headroom to the negative rail must be respected when operating from a single 5 V rail.
Recommandé
Temperature Control and Thermostat Loops
The LM324APWRG4 appears in heater controllers, thermostat modules and fan-speed regulators as the error amplifier comparing a resistive sensor against a reference and driving an MOSFET or relay driver. Its wide supply range allows the loop to run from the same rail as the actuator, and the low, supply-independent supply-current drain suits battery-backed thermostats. The internally compensated architecture is unity-gain stable, so it can be used directly as a comparator-style element with a hysteresis network. Compensation capacitors should be sized from the datasheet gain-bandwidth guidance, and the output transistor base drive should be current-limited to protect the amplifier output stage.
Recommandé
General Instrumentation and Test Equipment
In bench instruments, measurement front ends and laboratory modules, the LM324APWRG4 is used for buffer, attenuator and active-filter stages that need four channels of general-purpose gain around a single supply. The 14-pin TSSOP outline lets a compact instrument board place four amplifiers in the space of one or two discrete packages, and the wide 32 V total supply rating tolerates the higher rails used in ±15 V style bench circuits. Note that the amplifier is not a precision part: for accuracy better than a few millivolts of error, choose a low-offset, low-noise amplifier, and for rail-to-rail battery operation use a modern low-voltage quad amplifier instead.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM324APWRG4 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM324APWR | LM324PWRG4 | LM324PWR | LM324KPWR | LM324APWR |
|---|---|---|---|---|---|---|
| Package | TSSOP-14 (PW) | TSSOP-14 (PW) - same | TSSOP-14 (PW) - same | TSSOP-14 (PW) - same | TSSOP-14 (PW) - same | TSSOP-14 (PW) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | KEC |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 | 4 |
Principaux différenciateurs
- Tighter input offset voltage than the base LM324 grade (vs LM324PWRG4)
- Four amplifiers in a compact 14-pin TSSOP footprint (vs KEC LM324APWR)
- Low, supply-independent quiescent current (vs LM324KPWR)
- RoHS-compliant green assembly with active product status (vs LM324PWR)
Notes de conception
Estimated: with a single 5 V rail, four channels at 0.8 mA typ each draw about 3.2 mA typ total, or roughly 16 mW of quiescent dissipation, so supply sizing is driven by the load currents at pins 1, 7, 8 and 14 rather than by bias current. Place a 100 nF ceramic decoupling capacitor as close as possible to pin 4 (V+) and a second 100 nF capacitor directly across pins 4 and 11, with a 1 uF to 10 uF bulk capacitor on the rail. Because output current is sourced from the supply pins, route output traces separately from the input network to limit coupling.
The LM324 is not rail-to-rail on either input or output. On a single 5 V supply the usable common-mode input range is roughly 0 V to 3.5 V and the output only swings to within about 50 mV of ground, so any signal or command exceeding those limits clips. Design the signal path so that the maximum expected input stays inside the common-mode window and add headroom when driving a load that needs a full 0 to 5 V swing. For true 0 V to 5 V output capability, select a rail-to-rail quad amplifier instead.
Keep each amplifier's feedback network (typically 1 kOhm to 100 kOhm resistors plus a capacitor) within a few millimetres of the output and inverting input pins, and route the non-inverting input away from the output trace and from the V+ pin. Place the ground return of shunt and current-sense inputs as a differential pair to avoid ground-drop errors. For adjacent-channel designs, avoid sharing a long ground path between channels A and D, since the four amplifiers are not internally isolated.
Estimated: because the amplifier is internally compensated for unity-gain stability, closed-loop noise gain above about 10 amplifies the offset and noise of the single-ended output stage, so high-gain applications should be checked for peaking at the datasheet gain-bandwidth product. Add a small isolation resistor (10 to 100 Ohm) between the amplifier output and the feedback tap when driving capacitive loads of more than about 100 pF to prevent oscillation. In switched-capacitor or rectifier applications, add a small anti-alias capacitor and verify the settling behaviour before the ADC sample window.
Informations de conformité
The G4 suffix identifies a RoHS-compliant, lead-free green assembly of the Texas Instruments LM324A family; the REACH declaration is published in the same compliance data set for this orderable code. The part is a commercial/industrial general-purpose grade and is not AEC-Q100 qualified for automotive use.