LM339M/NOPB - Low-Power Quad Comparator | Texas Instruments
Référence : LM339M/NOPB ✓ ActifLM339M/NOPB Présentation
A comparator is an analog integrated circuit that determines whether one input voltage is higher or lower than another. Rather than amplifying the difference into a linear output, it produces a digital decision at its output. The LM339 belongs to the comparator hierarchy within analog and mixed-signal integrated circuits, providing four conversion elements in one package and reducing component count compared with discrete single comparators.
The key characteristics of LM339M/NOPB include four comparator channels, an open-collector output stage, a 14-pin SOIC package, and a commercial operating-temperature range of 0°C to 70°C. Open-collector outputs allow multiple comparator outputs to share a wired bus when each output has an appropriate pull-up resistor. This architecture is useful in window detectors, level alarms, sensor interfaces, relay-control circuits, and low-voltage logic threshold systems.
The four channels are electrically independent, allowing each comparator to monitor a different threshold while sharing the same supply pins. Because the outputs are open collector, external pull-up components are required when a logic-high output is needed. The collector output also provides flexibility for selecting a pull-up voltage independently of the comparator supply voltage, subject to the device absolute-maximum and operating limits defined by the manufacturer.
Typical implementations compare a sensor output against a reference voltage, detect overvoltage or undervoltage conditions, or translate an analog threshold into a logic event. The open-collector architecture is particularly useful when multiple comparators must indicate a shared fault. Designers should also account for input offset, input bias current, supply-current requirements, output pull-up resistance, and the switching behavior associated with the bipolar comparator topology.
For a new PCB, place the device close to the signals being compared and maintain a continuous ground reference. Use stable decoupling from the supply pins to ground and route the pull-up resistors away from sensitive analog inputs. For an existing 14-SOIC design, verify the replacement’s offset voltage, supply range, output architecture, input common-mode range, and propagation delay before approving a substitution.
This product page combines package and functional details, replacement guidance, application-specific design considerations, and a parameter-by-parameter comparison. It also distinguishes true SOIC drop-in options from similarly named parts that use incompatible packages, helping engineers shorten qualification time without overlooking electrical differences.
Alternatives de remplacement direct pour LM339M/NOPB — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM339M/NOPB (même facteur de forme et même empreinte) — différant par Comparator Type, Logic Compatibility, Output Type, Package, Number of Comparators.
LM339M
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LMV339M/NOPB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LM339M
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM339DG
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM339M/NOPB Valeurs maximales et caractéristiques électriques
| Comparator Type | Standard general-purpose differential comparator |
| Number of Channels | 4 channels |
| Type de sortie | Open collector |
| Logic Compatibility | TTL, MOS, and CMOS compatible |
| Boîtier | 14-pin SOIC (D) |
| Nombre de broches | 14 pins |
| Plage de température de fonctionnement | 0°C to 70°C |
| Type de montage | Surface mount |
Configuration des broches de LM339M/NOPB
| Broche 1 | OUT1 — Comparator 1 open-collector output |
| Broche 2 | IN1- — Comparator 1 inverting input |
| Broche 3 | IN1+ — Comparator 1 non-inverting input |
| Broche 4 | GND — Ground connection |
| Broche 5 | IN2+ — Comparator 2 non-inverting input |
| Broche 6 | IN2- — Comparator 2 inverting input |
| Broche 7 | OUT2 — Comparator 2 open-collector output |
| Broche 8 | OUT3 — Comparator 3 open-collector output |
| Broche 9 | IN3- — Comparator 3 inverting input |
| Broche 10 | IN3+ — Comparator 3 non-inverting input |
| Broche 11 | VCC — Positive supply connection |
| Broche 12 | IN4+ — Comparator 4 non-inverting input |
| Broche 13 | IN4- — Comparator 4 inverting input |
| Broche 14 | OUT4 — Comparator 4 open-collector output |
Applications typiques
LM339M/NOPB convient pour 6 applications: Industrial Threshold Detection, Open-Collector Alarm Bus, Sensor Signal Conditioning, Power-Supply Overvoltage Detection, Battery Charger Control, LED Lighting Control.
Industrial Threshold Detection
The LM339M/NOPB is appropriate for comparing a sensor or divided supply voltage against a reference threshold in industrial monitoring equipment. Its four independent channels can supervise multiple voltages while sharing one 14-SOIC footprint, reducing board area compared with four separate single comparators. The open-collector output can pull down an alarm line or drive an input rated for the selected pull-up voltage. Because the commercial device is specified for 0°C to 70°C, enclosure temperature must remain inside that range or a wider-temperature grade must be selected.
Recommandé
Open-Collector Alarm Bus
The four open-collector outputs of the LM339M/NOPB can monitor separate fault conditions and share a common wired-alarm line. Each comparator pulls the bus low when its condition is met, while a single pull-up resistor restores the logic-high state when no fault is active. This arrangement reduces the number of digital inputs required by a controller. Design the pull-up for the receiver’s logic thresholds and verify that every comparator channel remains within its specified common-mode and supply limits during startup and fault transients.
Recommandé
Sensor Signal Conditioning
The LM339M/NOPB can convert an analog sensor level into a clean threshold event for a microcontroller or control system. Its differential inputs allow a sensor signal to be compared with a stable reference, and the open-collector result can directly pull an interrupt or digital input low. Place the comparator near the protected analog domain to minimize noise pickup, and use a pull-up compatible with the digital rail. Stable reference generation and sensor grounding are as important as comparator selection because they directly determine the switching threshold and false-alarm behavior.
Recommandé
Power-Supply Overvoltage Detection
The LM339M/NOPB can supervise a divided power rail in an overvoltage or undervoltage detection circuit. Four channels provide flexibility for monitoring several rails or combining conditions, while the open-collector output can alert a system controller. The sensing network determines accuracy, so resistor tolerance and reference behavior should be included in the error budget. Also verify the comparator’s maximum supply and input voltages against the monitored rail, including transients that may exceed nominal operating conditions.
Recommandé
Battery Charger Control
In a simple charger-control circuit, the LM339M/NOPB can compare a battery or adapter voltage with a reference and control a switching element or status line. Four channels allow voltage and current thresholds to be monitored with one package. The open-collector output is useful for driving a pull-up-defined status signal or an external control stage, but it does not directly provide a regulated charger output. Thermal design, source impedance, filtering, and safe separation between charger and load paths must be handled by the surrounding circuit.
Recommandé
LED Lighting Control
The LM339M/NOPB can compare a control signal with a reference and translate the result into an LED-driver enable or status indication. Open-collector outputs allow the indicator logic to use a pull-up rail selected independently from the comparator supply. Multiple channels can support threshold-based brightness bands, fault indication, or sequencing. Keep the LED current and switching node physically separated from the comparator inputs, and use the four channels only when each input remains inside the manufacturer’s specified common-mode and differential-input limits.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM339M/NOPB — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM339M | LMV339M/NOPB | LM339M | LM339DG |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | onsemi |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Comparator Function | General-purpose differential comparator | General-purpose differential comparator | General-purpose differential comparator | General-purpose differential comparator | LM339-family comparator |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector |
| Input Technology | Bipolar LM339 comparator | Bipolar LM339 comparator | CMOS comparator | LM339-family comparator | LM339-family comparator |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Principaux différenciateurs
- Four independent threshold-monitoring channels in one 14-SOIC package (vs onsemi LM339M)
- Open-collector output supports wired fault buses (vs onsemi LM339DG)
- Direct continuity with the original Texas Instruments LM339 design (vs LMV339M/NOPB)
Notes de conception
Install a pull-up resistor on every open-collector output that must drive a logic-high state. The resistor sets the rise time and determines the current drawn while an output transistor is active. Calculate the resistor using the receiving logic’s input-current requirement and the maximum output-low voltage, then check that the resulting rise time meets the system timing requirement.
Place the supply bypass capacitor close to the VCC and GND pins, and use a low-impedance ground plane. Route the four comparator inputs away from switching nodes and pull-up-return currents. When multiple open-collector outputs share a bus, keep their traces short and place the common pull-up near the receiver or at a location that limits trace resistance and coupling.
Do not treat every LM339-family ordering code as a footprint-compatible replacement. The M suffix denotes the 14-SOIC configuration, while N commonly denotes a 14-pin through-hole package. Before substituting another manufacturer’s LM339M or LM339DG, verify pin numbering, open-collector output behavior, input common-mode range, supply limits, offset, and propagation delay.
Keep threshold references and sensor inputs away from pull-up resistors and digital return paths because switching edges can couple into high-impedance comparator inputs. If the input source has appreciable capacitance or noise, use appropriate filtering and confirm that filtering does not introduce excessive delay in a safety- or control-loop application. A solid ground reference is essential for repeatable threshold decisions.
Informations de conformité
The manufacturer product page identifies LM339M/NOPB as a 14-pin SOIC comparator, but the supplied manufacturer information does not state exact RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for this orderable part.