LT1806IS8 - 325MHz RRIO Precision Op Amp | Analog Devices
Référence : LT1806IS8 ✓ ActifLT1806IS8 Présentation
An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify small voltage signals. The LT1806 belongs to the voltage-feedback amplifier hierarchy and provides rail-to-rail input and output operation, allowing the signal path to operate close to the supply rails in low-voltage systems. Its combination of high bandwidth, fast slew rate, and broad input and output ranges supports accurate signal conditioning at higher frequencies than conventional general-purpose amplifiers.
Principal features include a 325 MHz gain-bandwidth product, 140 V/us slew rate, 85 mA output current, rail-to-rail input, and rail-to-rail output. The manufacturer also identifies the LT1806 as a low-noise, low-distortion precision amplifier that is unity-gain stable. These characteristics make it useful in active filters, instrumentation signal chains, data converters, communications equipment, and other circuits requiring accurate signal amplification with low distortion.
The device uses a conventional voltage-feedback architecture with a standard single-amplifier pinout. Its high bandwidth allows small-signal operation well above the frequencies commonly supported by general-purpose op amps, while the 140 V/us slew rate gives it the transient response needed for pulse, waveform, and active-filter stages. Rail-to-rail input and output behavior increases usable signal range in low-voltage systems, although input common-mode and output-swing limitations must still be considered under the chosen supply voltage and load.
Typical applications include precision active filters, instrumentation amplifiers, low-level sensor signal conditioning, ADC and DAC interface circuits, communications receivers, and precision waveform-generation or buffer stages. The LT1806IS8 is particularly appropriate when the signal bandwidth is beyond the practical range of a general-purpose amplifier but the circuit does not require a fully differential amplifier or a multi-amplifier array.
For PCB implementation, use short feedback paths, place input and output components close to the device, and maintain a clean return connection to minimize parasitic feedback. Avoid excessive capacitive loading at the output because the amplifier must drive the capacitance while preserving stability and distortion performance. The 8-pin SO package should be handled using standard moisture-sensitive assembly practices for the specified package and manufacturing process.
This product record combines the LT1806IS8 manufacturer specifications with application analysis, package information, verified drop-in candidates, comparison parameters, and practical design guidance. It is intended to help engineers determine whether its 325 MHz bandwidth, low distortion, and rail-to-rail operation fit a specific signal-chain design.
Alternatives de remplacement direct pour LT1806IS8 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
LT1806IS8#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LT1806CS8#PBF
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LT1806IS8 Valeurs maximales et caractéristiques électriques
| Amplifier Type | Single voltage-feedback operational amplifier |
| Gain-Bandwidth Product | 325 MHz |
| Slew Rate | 140 V/us |
| Output Current | 85 mA |
| Tension d'alimentation | ±6.3 V or 12.6 V total |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Unity-Gain Stability | Unity-gain stable |
| Number of Channels | 1 channel |
| Boîtier | 8-pin SO package |
| Type de montage | Surface mount |
Configuration des broches de LT1806IS8
| Broche 1 | OFFSET NULL — Offset-voltage adjustment input |
| Broche 2 | INVERTING INPUT — Inverting input |
| Broche 3 | NONINVERTING INPUT — Non-inverting input |
| Broche 4 | V− — Negative supply connection |
| Broche 5 | OFFSET NULL — Offset-voltage adjustment input |
| Broche 6 | OUTPUT — Amplifier output |
| Broche 7 | V+ — Positive supply connection |
| Broche 8 | NC — Not connected |
Applications typiques
LT1806IS8 convient pour 6 applications: Precision Active Filters, Instrumentation Signal Conditioning, ADC and DAC Interface Circuits, Communications Receiver Signal Path, Precision Waveform Buffering, Low-Level Sensor Front Ends.
Precision Active Filters
The LT1806IS8 fits precision active-filter stages because its 325 MHz gain-bandwidth product preserves signal amplitude and phase accuracy well beyond the range of a conventional general-purpose amplifier. The 140 V/us slew rate also limits distortion when the filter must reproduce square-wave or fast transient content. In a second-order low-pass, high-pass, or band-pass network, the amplifier operates with the feedback components to determine selectivity and gain. Its unity-gain stability supports straightforward closed-loop implementation, while rail-to-rail input and output operation can increase usable dynamic range in low-voltage designs. Component tolerances, noise gain, and stability margin remain important because the very high bandwidth can amplify parasitic capacitance and board-level feedback if layout is poor.
Recommandé
Instrumentation Signal Conditioning
The LT1806IS8 is appropriate for instrumentation signal conditioning where sensor outputs are small, bandwidth-intensive, and susceptible to distortion. Its rail-to-rail input stage accepts signals across much of the supply span, while the 325 MHz gain-bandwidth product supports closed-loop gains that preserve useful signal bandwidth. The 140 V/us slew rate provides fast recovery when the conditioned waveform contains sharp transitions. In an instrumentation-amplifier or differential-filter topology, the LT1806 can form one of the active gain stages. Designers should still verify input bias current, offset voltage, drift, common-mode range, and noise against the sensor and ADC requirements. Keeping feedback resistors and input traces compact reduces parasitic effects that become increasingly relevant at this device’s operating bandwidth.
Recommandé
ADC and DAC Interface Circuits
The LT1806IS8 can serve as a high-speed driver or buffer between a converter and the next circuit stage. Its 325 MHz gain-bandwidth product supports wide-band converter interfaces, while the 140 V/us slew rate helps maintain fidelity during rapid output transitions. Rail-to-rail output increases usable signal swing, and the specified 85 mA output current provides drive capability beyond many low-power op amps. When the LT1806 drives a sampling capacitor or cable, settling behavior and output loading must be checked together with the converter acquisition window. Place the amplifier near the converter, use short traces, and minimize capacitance around the output node. These practices help prevent the high bandwidth and drive capability from producing ringing or distortion.
Recommandé
Communications Receiver Signal Path
The LT1806IS8 is suitable for low-level communications receiver stages that require accurate amplification without the distortion of a lower-bandwidth device. Its 325 MHz gain-bandwidth product handles higher-frequency components in modulated or wideband signals, and the 140 V/us slew rate supports fast waveform transitions. Rail-to-rail input and output operation can be useful in compact, low-voltage receiver architectures. In a typical chain, the amplifier may provide gain, impedance conversion, or filtering between mixer or filter blocks and a downstream converter. The design should account for noise, gain flatness, output loading, and adjacent-channel rejection rather than relying on bandwidth alone. Short RF-style signal routing and a continuous ground return help maintain predictable behavior at frequencies where parasitic inductance and capacitance become significant.
Recommandé
Precision Waveform Buffering
The LT1806IS8 works well as a precision buffer for low-level waveforms where source impedance is high and the following stage requires low distortion. The buffer configuration uses the amplifier’s unity-gain stability, while the 325 MHz gain-bandwidth product avoids the attenuation and phase shift that a slower amplifier would introduce. Its 140 V/us slew rate supports abrupt transitions, and rail-to-rail output operation helps retain amplitude margin in compact systems. The 85 mA output-current capability is relevant when driving a moderate capacitive or resistive load, but the exact load still needs to remain within the electrical limits. Keep the output trace short, avoid long probe or cable connections, and place any termination capacitor as close as practical to minimize feedback through parasitic capacitance.
Recommandé
Low-Level Sensor Front Ends
The LT1806IS8 can amplify low-level sensor signals when the system also requires high bandwidth and low distortion. Rail-to-rail input operation is valuable in battery-powered or low-voltage equipment, where usable signal headroom may be limited. The 325 MHz gain-bandwidth product permits moderate closed-loop gains without severe bandwidth reduction, and the 140 V/us slew rate preserves fast sensor transients. The LT1806 may be used in a gain stage, low-pass filter, or drive path toward an ADC. Offset, bias current, noise density, and drift must be matched to the sensor’s output impedance and accuracy requirements; those values are important even when speed is adequate. High-impedance sensor nodes also demand careful guarding and short PCB traces to prevent leakage and noise pickup.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LT1806IS8 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LT1806IS8#PBF | LT1806CS8#PBF |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SO | 8-pin SO - same | 8-pin SO - same |
| Amplifier Configuration | Single | Single | Single |
| Gain-Bandwidth Product | 325 MHz | 325 MHz | 325 MHz |
| Slew Rate | 140 V/us | 140 V/us | 140 V/us |
| Output Current | 85 mA | 85 mA | 85 mA |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Supply Voltage | ±6.3 V or 12.6 V total | ±6.3 V or 12.6 V total | ±6.3 V or 12.6 V total |
| Temperature Grade | Industrial grade indicated by IS suffix | Industrial grade indicated by IS suffix | Commercial grade indicated by CS suffix |
| Lead-Free Ordering Option | Ordering suffix not stated in product title | #PBF | #PBF |
Principaux différenciateurs
- Maintains the same high-speed electrical performance across the listed drop-in candidates (vs LT1806IS8#PBF)
- Offers the IS grade for applications requiring the industrial temperature option (vs LT1806CS8#PBF)
- Combines wide bandwidth with rail-to-rail signal range (vs LT1806IS8#PBF)
Notes de conception
Place the LT1806IS8 close to the signal source and feedback network, and keep input, output, and ground paths physically short. At 325 MHz gain-bandwidth product, trace inductance, pad capacitance, and ground impedance can affect stability and distortion even when the schematic appears ideal. Connect supply pins to a low-impedance plane or dense via field, and avoid routing high-speed output beneath sensitive input nodes. The 8-pin SO footprint should be checked against the land pattern and pin orientation in the package drawing.
Do not assume that rail-to-rail input and output labels remove all operating constraints. Check the datasheet limits for input common-mode voltage, output swing, output-current capability, capacitive loading, and power dissipation at the selected supply and load. Avoid driving large capacitive loads directly unless the stability and transient-response guidance is followed. The 85 mA output-current figure is a device capability, not a recommendation to operate continuously at that current.
Use short, direct feedback components and provide a continuous return path beneath the amplifier. Decouple each supply connection close to the package with appropriately characterized capacitors, using additional bulk capacitance where the upstream supply is remote. Because this device has 325 MHz gain-bandwidth product and 140 V/us slew rate, ringing and instability may appear at frequencies that seem high for an SOIC-8 amplifier. Probe using short ground springs or controlled impedance methods rather than long ground leads.
Informations de conformité
The #PBF ordering option identifies a lead-free finish, but separate RoHS, REACH, halogen-free, and conflict-minerals declarations were not stated in the product information. Automotive qualification is not expected for this industrial amplifier grade.