Analog Devices

LT1806IS8 - 325MHz RRIO Precision Op Amp | Analog Devices

MPN: LT1806IS8 ✓ Nakahanda
±6.3 V or 12.6 V total Vdss 85 mA Id 8-pin SO package Package
MOQ: 1 |

LT1806IS8 Ulas

The Analog Devices LT1806IS8 is a single, rail-to-rail input and output precision operational amplifier with a 325 MHz gain-bandwidth product, 140 V/us slew rate, and 85 mA output drive capability. The device is packaged in an 8-pin SO package and is specified for applications requiring low distortion, low noise, and high-speed closed-loop response.

An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify small voltage signals. The LT1806 belongs to the voltage-feedback amplifier hierarchy and provides rail-to-rail input and output operation, allowing the signal path to operate close to the supply rails in low-voltage systems. Its combination of high bandwidth, fast slew rate, and broad input and output ranges supports accurate signal conditioning at higher frequencies than conventional general-purpose amplifiers.

Principal features include a 325 MHz gain-bandwidth product, 140 V/us slew rate, 85 mA output current, rail-to-rail input, and rail-to-rail output. The manufacturer also identifies the LT1806 as a low-noise, low-distortion precision amplifier that is unity-gain stable. These characteristics make it useful in active filters, instrumentation signal chains, data converters, communications equipment, and other circuits requiring accurate signal amplification with low distortion.

The device uses a conventional voltage-feedback architecture with a standard single-amplifier pinout. Its high bandwidth allows small-signal operation well above the frequencies commonly supported by general-purpose op amps, while the 140 V/us slew rate gives it the transient response needed for pulse, waveform, and active-filter stages. Rail-to-rail input and output behavior increases usable signal range in low-voltage systems, although input common-mode and output-swing limitations must still be considered under the chosen supply voltage and load.

Typical applications include precision active filters, instrumentation amplifiers, low-level sensor signal conditioning, ADC and DAC interface circuits, communications receivers, and precision waveform-generation or buffer stages. The LT1806IS8 is particularly appropriate when the signal bandwidth is beyond the practical range of a general-purpose amplifier but the circuit does not require a fully differential amplifier or a multi-amplifier array.

For PCB implementation, use short feedback paths, place input and output components close to the device, and maintain a clean return connection to minimize parasitic feedback. Avoid excessive capacitive loading at the output because the amplifier must drive the capacitance while preserving stability and distortion performance. The 8-pin SO package should be handled using standard moisture-sensitive assembly practices for the specified package and manufacturing process.

This product record combines the LT1806IS8 manufacturer specifications with application analysis, package information, verified drop-in candidates, comparison parameters, and practical design guidance. It is intended to help engineers determine whether its 325 MHz bandwidth, low distortion, and rail-to-rail operation fit a specific signal-chain design.

Mga alternatibo na pwedeng ilagay na LT1806IS8 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

LT1806IS8#PBF

✅ Drop-In
📦 8-pin SO
Same 325 MHz gain-bandwidth product, 140 V/us slew rate, 85 mA output current, and 8-pin SO pinout; ordering suffix identifies the lead-free option, with no electrical difference stated

📋 Alternatibo na Reference (hindi sa katalogo)

LT1806CS8#PBF

✅ Drop-In
📦 8-pin SO
Same LT1806 family, 325 MHz gain-bandwidth product, 140 V/us slew rate, and 8-pin SO pinout; C suffix denotes a different temperature grade from the IS grade

📋 Alternatibo na Reference (hindi sa katalogo)

LT1806IS8 Mga Pinakamataas na Rating at Electrical Characteristics

Amplifier Type Single voltage-feedback operational amplifier
Gain-Bandwidth Product 325 MHz
Slew Rate 140 V/us
Output Current 85 mA
Volte ng Pagbibigay ±6.3 V or 12.6 V total
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Unity-Gain Stability Unity-gain stable
Number of Channels 1 channel
Packhaging 8-pin SO package
Uri ng Pagpapasok Surface mount

Pin Configuration ng LT1806IS8

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 OFFSET NULL — Offset-voltage adjustment input
Pin 2 INVERTING INPUT — Inverting input
Pin 3 NONINVERTING INPUT — Non-inverting input
Pin 4 V− — Negative supply connection
Pin 5 OFFSET NULL — Offset-voltage adjustment input
Pin 6 OUTPUT — Amplifier output
Pin 7 V+ — Positive supply connection
Pin 8 NC — Not connected

Tipikal na mga Gamit

LT1806IS8 ay nararapat para sa 6 aplikasyons: Precision Active Filters, Instrumentation Signal Conditioning, ADC and DAC Interface Circuits, Communications Receiver Signal Path, Precision Waveform Buffering, Low-Level Sensor Front Ends.

📡

Precision Active Filters

The LT1806IS8 fits precision active-filter stages because its 325 MHz gain-bandwidth product preserves signal amplitude and phase accuracy well beyond the range of a conventional general-purpose amplifier. The 140 V/us slew rate also limits distortion when the filter must reproduce square-wave or fast transient content. In a second-order low-pass, high-pass, or band-pass network, the amplifier operates with the feedback components to determine selectivity and gain. Its unity-gain stability supports straightforward closed-loop implementation, while rail-to-rail input and output operation can increase usable dynamic range in low-voltage designs. Component tolerances, noise gain, and stability margin remain important because the very high bandwidth can amplify parasitic capacitance and board-level feedback if layout is poor.

🏭

Instrumentation Signal Conditioning

The LT1806IS8 is appropriate for instrumentation signal conditioning where sensor outputs are small, bandwidth-intensive, and susceptible to distortion. Its rail-to-rail input stage accepts signals across much of the supply span, while the 325 MHz gain-bandwidth product supports closed-loop gains that preserve useful signal bandwidth. The 140 V/us slew rate provides fast recovery when the conditioned waveform contains sharp transitions. In an instrumentation-amplifier or differential-filter topology, the LT1806 can form one of the active gain stages. Designers should still verify input bias current, offset voltage, drift, common-mode range, and noise against the sensor and ADC requirements. Keeping feedback resistors and input traces compact reduces parasitic effects that become increasingly relevant at this device’s operating bandwidth.

🔧

ADC and DAC Interface Circuits

The LT1806IS8 can serve as a high-speed driver or buffer between a converter and the next circuit stage. Its 325 MHz gain-bandwidth product supports wide-band converter interfaces, while the 140 V/us slew rate helps maintain fidelity during rapid output transitions. Rail-to-rail output increases usable signal swing, and the specified 85 mA output current provides drive capability beyond many low-power op amps. When the LT1806 drives a sampling capacitor or cable, settling behavior and output loading must be checked together with the converter acquisition window. Place the amplifier near the converter, use short traces, and minimize capacitance around the output node. These practices help prevent the high bandwidth and drive capability from producing ringing or distortion.

🌐

Communications Receiver Signal Path

The LT1806IS8 is suitable for low-level communications receiver stages that require accurate amplification without the distortion of a lower-bandwidth device. Its 325 MHz gain-bandwidth product handles higher-frequency components in modulated or wideband signals, and the 140 V/us slew rate supports fast waveform transitions. Rail-to-rail input and output operation can be useful in compact, low-voltage receiver architectures. In a typical chain, the amplifier may provide gain, impedance conversion, or filtering between mixer or filter blocks and a downstream converter. The design should account for noise, gain flatness, output loading, and adjacent-channel rejection rather than relying on bandwidth alone. Short RF-style signal routing and a continuous ground return help maintain predictable behavior at frequencies where parasitic inductance and capacitance become significant.

⚡

Precision Waveform Buffering

The LT1806IS8 works well as a precision buffer for low-level waveforms where source impedance is high and the following stage requires low distortion. The buffer configuration uses the amplifier’s unity-gain stability, while the 325 MHz gain-bandwidth product avoids the attenuation and phase shift that a slower amplifier would introduce. Its 140 V/us slew rate supports abrupt transitions, and rail-to-rail output operation helps retain amplitude margin in compact systems. The 85 mA output-current capability is relevant when driving a moderate capacitive or resistive load, but the exact load still needs to remain within the electrical limits. Keep the output trace short, avoid long probe or cable connections, and place any termination capacitor as close as practical to minimize feedback through parasitic capacitance.

🧩

Low-Level Sensor Front Ends

The LT1806IS8 can amplify low-level sensor signals when the system also requires high bandwidth and low distortion. Rail-to-rail input operation is valuable in battery-powered or low-voltage equipment, where usable signal headroom may be limited. The 325 MHz gain-bandwidth product permits moderate closed-loop gains without severe bandwidth reduction, and the 140 V/us slew rate preserves fast sensor transients. The LT1806 may be used in a gain stage, low-pass filter, or drive path toward an ADC. Offset, bias current, noise density, and drift must be matched to the sensor’s output impedance and accuracy requirements; those values are important even when speed is adequate. High-impedance sensor nodes also demand careful guarding and short PCB traces to prevent leakage and noise pickup.

What is the LT1806IS8?
The LT1806IS8 is a single, rail-to-rail input and output precision operational amplifier with a 325 MHz gain-bandwidth product and 140 V/us slew rate. According to the Analog Devices LT1806/LT1807 datasheet, it is unity-gain stable and supplied in an 8-pin SO package. Its combination of high speed, low distortion, and low noise is intended for precision filters, instrumentation, communications, and data-converter interface circuits.
What are the key specifications of LT1806IS8 that engineers should know?
The LT1806IS8 combines a 325 MHz gain-bandwidth product, 140 V/us slew rate, 85 mA output current, and rail-to-rail input and output operation. The Analog Devices manufacturer datasheet identifies the amplifier as a unity-gain-stable, low-noise, low-distortion precision op amp. It is a single amplifier in an 8-pin SO package and is suited to signal-conditioning stages requiring substantially more bandwidth than general-purpose amplifiers.
What is the operating voltage of LT1806IS8?
The LT1806IS8 operates from a total supply of 12.6 V, equivalent to ±6.3 V when powered from a dual supply. According to the manufacturer datasheet and product listing, it is a precision operational amplifier intended for low-voltage, high-performance signal chains. Use the datasheet's electrical-characteristics table to confirm operation across the complete supply range and under the intended input common-mode and output conditions.
What is the gain-bandwidth product of LT1806IS8?
The LT1806IS8 has a 325 MHz gain-bandwidth product. According to the Analog Devices LT1806/LT1807 datasheet, this bandwidth supports accurate amplification of signals well above the range of general-purpose op amps. In a noise-gain configuration, the usable closed-loop bandwidth and stability depend on the feedback network, so the actual circuit response should be evaluated with the intended gain and compensation.
Why is the LT1806IS8 suitable for active filters?
The LT1806IS8 is suitable for active filtering because its 325 MHz gain-bandwidth product and 140 V/us slew rate provide high-speed closed-loop response and accurate large-signal reproduction. According to the manufacturer datasheet, the device is unity-gain stable and optimized for low distortion. These characteristics support wide-band filters, signal conditioners, and ADC interface stages where ordinary op amps may introduce excessive gain error or distortion.
What can replace the LT1806IS8?
The LT1806IS8#PBF is a qualified drop-in candidate because it uses the same Analog Devices LT1806 electrical configuration and 8-pin SO footprint. The LT1806CS8#PBF is another same-package candidate when its commercial temperature grade satisfies the application. Before replacement, verify the exact temperature grade, supply range, offset and drift specifications, output-drive requirements, and PCB orientation in the manufacturer datasheet.
Is LT1806IS8 the same as LT1806IS8#PBF?
The LT1806IS8 and LT1806IS8#PBF identify the same LT1806 single-amplifier configuration in an 8-pin SO package, with #PBF identifying the lead-free ordering option. The Analog Devices datasheet covers the LT1806 family and provides the standard single-op-amp pinout. Confirm package marking, temperature grade, and lead-free procurement requirements before treating the two order codes as interchangeable for a production release.
LT1806IS8 vs LT1806CS8#PBF: which is better for industrial use?
The LT1806IS8 is the better choice when the industrial design requires the IS temperature grade, while LT1806CS8#PBF is appropriate only if the commercial grade covers the required ambient range. Both use the same LT1806 family architecture and 8-pin SO package. The Analog Devices datasheet should be used to compare the exact grade limits, and the LT1806IS8 is the safer selection where the industrial-grade range is required.
When should I choose LT1806IS8 over a lower-bandwidth op amp?
Choose the LT1806IS8 when the signal path requires high closed-loop bandwidth, rapid slew rate, low distortion, or operation close to the supply rails. Its 325 MHz gain-bandwidth product and 140 V/us slew rate provide considerably more performance than a general-purpose amplifier. For low-frequency precision-only signals, a lower-bandwidth device may offer lower cost, lower power, or lower noise, so the required bandwidth should drive the decision.
Is LT1806IS8 suitable for ADC and DAC interface circuits?
The LT1806IS8 is suitable for high-speed ADC and DAC interface circuits because it combines rail-to-rail input and output operation with a 325 MHz gain-bandwidth product. According to the manufacturer datasheet, the amplifier also provides low distortion and 140 V/us slew rate. The surrounding converter still determines the practical bandwidth and settling requirements, so those specifications should be checked together with the LT1806 output-drive capability.
Where can I download the LT1806IS8 datasheet PDF?
The LT1806IS8 datasheet PDF is available from Analog Devices at the official LT1806/LT1807 datasheet link on this page. The document covers the LT1806 single and LT1807 dual precision op amps, including the LT1806 8-pin SO package, standard op-amp pinout, electrical characteristics, and application information. Use the package-specific ordering information to confirm the grade and suffix corresponding to LT1806IS8.
Where can I find the LT1806IS8 pinout?
The LT1806IS8 pinout is documented in the Analog Devices LT1806/LT1807 manufacturer datasheet under the package and pin-description information. The LT1806 uses the standard single-op-amp arrangement in its 8-pin SO package, with offset-null, inverting and non-inverting inputs, supply pins, output, and exposed connections identified there. Use that pin-description table when assigning PCB nets and checking the exposed pad or no-connect location.
Where can I buy LT1806IS8 online and check its current price?
The current commercial terms for LT1806IS8 should be requested through the Request a Quote form on this page. The form is the appropriate route for checking unit availability, quantity breaks, lead time, and shipping requirements without relying on a stale price. For technical confirmation, use the Analog Devices product page and datasheet to verify the exact package, grade, and electrical configuration before placing an order.
What is the lead time for LT1806IS8?
The current lead time for LT1806IS8 depends on inventory, order quantity, and the requested delivery terms. Use the Request a Quote form on this page to obtain a current commitment and minimum-order details. The Analog Devices product page identifies the LT1806 as a production family, but production status alone does not establish a fixed lead time or guaranteed stock for every order quantity.
Is LT1806IS8 in stock?
Stock status for LT1806IS8 can change with order quantity and supply conditions, so use the Request a Quote form on this page for the current allocation. Provide the required quantity, target date, and shipment destination in the request. Before committing to the component, also confirm the exact LT1806IS8 package and temperature-grade marking with the Analog Devices ordering information.

Impormasyon ng Talumpati sa Engineering for LT1806IS8 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the LT1806IS8 when a single-channel, high-speed precision amplifier is required in an 8-pin SO design and the industrial temperature grade is appropriate. Its 325 MHz gain-bandwidth product, 140 V/us slew rate, and rail-to-rail input and output make it suitable for wide-band filters, communications paths, sensor conditioning, and converter interfaces. LT1806IS8#PBF is the preferred drop-in candidate when its lead-free ordering designation is required, because its core electrical ratings and footprint match the target. Select LT1806CS8#PBF only when its commercial temperature grade covers the complete operating environment and the procurement specification permits that grade. For a new design, compare the LT1806 against lower-bandwidth or lower-power op amps: the LT1806 provides the speed and drive needed for demanding signals, but those capabilities are unnecessary when the signal bandwidth is low and power or noise is the dominant system constraint.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto LT1806IS8#PBF LT1806CS8#PBF
Brand Analog Devices Analog Devices Analog Devices
Package 8-pin SO 8-pin SO - same 8-pin SO - same
Amplifier Configuration Single Single Single
Gain-Bandwidth Product 325 MHz 325 MHz 325 MHz
Slew Rate 140 V/us 140 V/us 140 V/us
Output Current 85 mA 85 mA 85 mA
Input Common-Mode Range Rail-to-rail Rail-to-rail Rail-to-rail
Output Swing Rail-to-rail Rail-to-rail Rail-to-rail
Supply Voltage ±6.3 V or 12.6 V total ±6.3 V or 12.6 V total ±6.3 V or 12.6 V total
Temperature Grade Industrial grade indicated by IS suffix Industrial grade indicated by IS suffix Commercial grade indicated by CS suffix
Lead-Free Ordering Option Ordering suffix not stated in product title #PBF #PBF

Pangunahing mga Pagkakaiba

  • Maintains the same high-speed electrical performance across the listed drop-in candidates (kumpara saLT1806IS8#PBF)
  • Offers the IS grade for applications requiring the industrial temperature option (kumpara saLT1806CS8#PBF)
  • Combines wide bandwidth with rail-to-rail signal range (kumpara saLT1806IS8#PBF)

Talaan ng Disenyo

Place the LT1806IS8 close to the signal source and feedback network, and keep input, output, and ground paths physically short. At 325 MHz gain-bandwidth product, trace inductance, pad capacitance, and ground impedance can affect stability and distortion even when the schematic appears ideal. Connect supply pins to a low-impedance plane or dense via field, and avoid routing high-speed output beneath sensitive input nodes. The 8-pin SO footprint should be checked against the land pattern and pin orientation in the package drawing.

Do not assume that rail-to-rail input and output labels remove all operating constraints. Check the datasheet limits for input common-mode voltage, output swing, output-current capability, capacitive loading, and power dissipation at the selected supply and load. Avoid driving large capacitive loads directly unless the stability and transient-response guidance is followed. The 85 mA output-current figure is a device capability, not a recommendation to operate continuously at that current.

Use short, direct feedback components and provide a continuous return path beneath the amplifier. Decouple each supply connection close to the package with appropriately characterized capacitors, using additional bulk capacitance where the upstream supply is remote. Because this device has 325 MHz gain-bandwidth product and 140 V/us slew rate, ringing and instability may appear at frequencies that seem high for an SOIC-8 amplifier. Probe using short ground springs or controlled impedance methods rather than long ground leads.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The #PBF ordering option identifies a lead-free finish, but separate RoHS, REACH, halogen-free, and conflict-minerals declarations were not stated in the product information. Automotive qualification is not expected for this industrial amplifier grade.

Data napatotohanan sa: 2026-11-19 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

lt1806is8 pbf LT1806IS8 datasheet LT1806IS8 datasheet pdf LT1806IS8 pinout LT1806IS8 equivalent LT1806IS8 replacement LT1806IS8 cross reference LT1806IS8 vs LT1806CS8#PBF Analog Devices LT1806IS8 LT1806IS8 price LT1806IS8 stock LT1806IS8 application circuit LT1806 325MHz op amp LT1806IS8 SOIC-8 pinout

Mga kaugnay na Mga Komponente at mga Tuntunin

Analog Devices Linear Technology LT1806IS8 LT1806IS8#PBF LT1806CS8#PBF LT1806 LT1807 operational amplifier op amp precision amplifier voltage-feedback amplifier rail-to-rail input rail-to-rail output gain-bandwidth product slew rate unity-gain stable low-noise amplifier low-distortion amplifier 8-pin SO package SOIC-8 surface-mount package precision active filter instrumentation signal conditioning ADC interface DAC interface
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ